summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-10-15mx5/6 clocks: Fix SDHC clocksBenoît Thébaudeau
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although they have dedicated clock paths. Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx51: Fix I2C clock ID checkBenoît Thébaudeau
There are only 2 I²C instances on i.MX51, but 3 on i.MX53. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix MXC_FEC_CLKBenoît Thébaudeau
The FEC clock does not come from PLL1, but from the IPG clock. The previous code was even inconsistent with itself, returning the IPG clock as expected for imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Simplify imx_get_cspiclk()Benoît Thébaudeau
The code handling the dividers was duplicated for each possible input clock, and this function can benefit from the newly introduced get_standard_pll_sel_clk() function instead of duplicating this mux handling code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_uart_clk()Benoît Thébaudeau
This function returned 66500000 instead of the correct lp_apm clock frequency if the CCM.CSCMR1.uart_clk_sel mux is set to 3. This patch fixes this issue by introducing the get_standard_pll_sel_clk() function that will be used by future patches to handle identical muxes used by many other clocks. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_ipg_per_clk()Benoît Thébaudeau
This fixes the "IPG PERCLK" frequency printed by the clocks command. The issue was that get_ipg_per_clk() used periph_clk instead of lp_apm in the case CCM.CBCMR.perclk_lp_apm_sel is set. It also fixes I²C support. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_periph_clk()Benoît Thébaudeau
In the case periph_clk comes from periph_apm_clk, the latter is selected by the CCM.CBCMR.periph_apm_sel mux, which can source the lp_apm clock from its input ♯2. get_periph_clk() returned 0 instead of the lp_apm clock frequency in this case. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_lp_apm()Benoît Thébaudeau
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024. In that case: - on i.MX51, this clock comes from the output of the FPM, - on i.MX53, this clock comes from the output of PLL4. This patch fixes the code accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Add and use CCSR definitionsBenoît Thébaudeau
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx51: Fix USB PHY clocksBenoît Thébaudeau
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks have different clock gate control bit-fields. The existing code was correct only for i.MX53, so this patch fixes the i.MX51 use case. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Jana Rapava <fermata7@gmail.com> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
2012-10-15mx5: Fix clock gate valuesBenoît Thébaudeau
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one of these bits like what was done is wrong and can lead to unpredictable behavior depending on the original value of these bit-fields. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5: Use explicit clock gate namesBenoît Thébaudeau
Use clock gate definitions having names showing clearly the gated clock instead of names giving only a register field index. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: CleanupBenoît Thébaudeau
Clean up the i.MX5 clock driver: - Use readl() and writel() instead of their __raw_ counterparts. - Use the clr/setbits_le32() family of macros rather than expanding code. - Use accessor macros for bit-fields instead of _MASK and _OFFSET. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15imx: Use MXC_I2C_CLK in imx i2c driverMatthias Weisser
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using MXC_I2C_CLK on all imx systems using i2c. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: add CPU revision 1.2Eric Benard
tested on a MCIMX257CJM4A which now reports : CPU: Freescale i.MX25 rev1.2 at 399 MHz Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx6q: Add basic support for mx6qsabreautoFabio Estevam
mx6qsabreauto is a board based on mx6q SoC with the following features: - 2GB of DDR3 - 2 USB ports - 1 HDMI output port - SPI NOR - 2 LVDS LCD ports - Gigabit Ethernet - Camera - eMMC and SD card slot - Multichannel Audio - CAN - SATA - NAND - PCIE - Video Input Add very basic support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15configs: mx6: Add a common config fileFabio Estevam
Add a common mx6 config file that can be shared between some mx6 boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15i.MX6: get rid of redundant struct src_regs (dupe of struct src)Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: define struct iomuxc and IOMUX_GPR2 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: Add ANATOP_PFD_480 bitfield constantsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: define IOMUX_GPR3 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: define bitfields for CHSCCDR registerEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: change register name for CCM_CHSCCDR to match ref. manualEric Nelson
Register CCM_CHSCCDR (offset 0x34 in CCM) is named CCM_CHSCCDR in reference manual, but was named chscdr in struct mxc_ccm_reg. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: provide functional names for CCM_CCGR0-CCGR6 bit fieldsEric Nelson
Add meaningful constants for each clock channels and use them for enabling and disabling i.MX6 clocks. Includes an update to enable/disable the IPU1 clock in drivers/video/ipu_common to remove IMX5x register access when used on i.MX6 as discussed in V1: http://patchwork.ozlabs.org/patch/185129/ Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15mx6qsabresd: Add 8-bit USDHC supportFabio Estevam
USDHC3 has 8 pins wired in mx6qsabresd. Configure the extra pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6qsabresd: Add Ethernet supportFabio Estevam
mx6qsabresd has a AR8031 Gigabit PHY. Add support for it. Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail. Tested on 1Gbp and 100Mbps networks. Suggested-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-15mx6: Add basic support for mx6qsabresd board.Fabio Estevam
mx6qsabresd is a board based on mx6q SoC with the following features: - 1GB of DDR3 - 1 USB OTG port - 1 HDMI output port - SPI NOR - LVDS panel - Gigabit Ethernet - Camera Connector - eMMC and SD card slot - Audio Add very basic support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6q: Factor out common DDR3 init codeFabio Estevam
Factor out common DDR3 initialization code, allowing easier maintainance of such scripts. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15pxa: Add code to examine cpu model and revisionLukasz Dalek
Add function which return CPU model and revision which can be used for cpu detection. Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
2012-10-15tegra: nand: add board pinmuxLucas Stach
Boards may require a different pinmux setup for NAND than the default one. Add a way to call into board specific code to set this up. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: clean up board include hellLucas Stach
The prototypes used in board files were all scattered out, which lead to code duplication between SPL and normal U-Boot and some prototypes not actually being used. Consolidate this in a common board header. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: add funcmux entry for NAND attached to KBCLucas Stach
Secondary config for the Flash attachment. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra20: rework UART GPIO handlingLucas Stach
Rename board provided gpio_config_uart() to gpio_early_init_uart() as it does the same thing as the equally called function provided by the uart-switch code. This allows to simply call this function in early board init whether or not we are building with CONFIG_UART_SWITCH defined. Also provide a weak symbol for this function, to avoid the need to provide this function for boards that don't need any fixup. This patch supersedes the earlier posted "tegra: convert gpio_config_uart to weak symbol". Build tested with MAKEALL -s tegra20 Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra20: add clock_set_pllout functionLucas Stach
Common practice on Tegra 2 boards is to use the pllp_out4 FO to generate the ULPI reference clock. For this to work we have to override the default hardware generated output divider. This function adds a clean way to do so. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra20: complete periph_id enumLucas Stach
Most Tegra boards output the ULPI reference clock on pad DEV2. Complete the periph_id enum so that we are able to enable this clock output circuit. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: enable CONFIG_CMD_PARTStephen Warren
This is extremely likely to be used from the boot.scr that Tegra's default bootcmd locates and executes. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15Tegra20: Move some include files to arch-tegra for sharing with Tegra30Tom Warren
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h. Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20' 'root' file. All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK. Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15Tegra20: Move some code files to common directories for upcoming Tegra30 ↵Tom Warren
patches. Move files that are going to be common between T20 and T30 into 'tegra-common' subdirs in AVP (arm720t), CPU (armv7), and shared (arch/arm/cpu/.) areas. Any files that are left behind in '/tegra20' will be copied to '/tegra30' subdirs and modified for that SoC. The 'common' files should need only minor changes. Include files (arch/arm/include/asm/arch-tegra/tegra20) will be done in a follow-on patch. Builds fine w/MAKEALL -s tegra20. Checkpatch.pl is clean. Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: Rename Medcom to Medcom-WideThierry Reding
Medcom is the marketing name for an older, PXA-based version of the same device. In order to avoid confusion, rename the Tegra-based version to the new marketing name. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: Update Avionic Design vendor prefixThierry Reding
The official vendor prefix for Avionic Design is now "ad". Update the board DTS files accordingly. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tools: Add a README note about fw_printenv lock fileJoe Hershberger
Add a mention of the lock file to the README for the fw_printenv tool. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Luka Perkov <uboot@lukaperkov.net>
2012-10-15env: Check for NULL pointer in envmatch()Joe Hershberger
If the pointer passed into envmatch() is NULL, return -1 instead of crashing. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15tools/env: Serialize calls to fw_*envJoe Hershberger
Use a lock file at /var/lock/fw_printenv.lock. Avoids seriously confusing the MTD driver. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15tools/env: Don't call env_init() in fw_getenv()Joe Hershberger
We will only call fw_getenv when the env has already been initialized. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15tools/env: Remove unneeded complexityJoe Hershberger
The length included the name length, and then it was subtracted back out on each use. Now we don't include it in the first place. Also realloc as we process arguments and eliminate memset. Use memcpy instead of manually copying each byte. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15tools/env: Use a board-specific default envJoe Hershberger
Originally added in aa701b94336b358798d676eef12a7b90bdac23f5 Before this patch, there was a hard-coded env that was used as default if the env in flash is detected as invalid. Now this tool (compiled for a given board) will share the default env with the u-boot for the board. Fix include of config.h Need to define "TEXT_BASE" when building the fw_env tool so that the default env will be correct for environments which use it. Define __ASSEMBLY__ when calling #include <config.h> so that we only get #defines (all we're interested in). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15common: cmd_bdinfo: fix type of value in print_lnumDaniel Schwierzeck
This fixes a warning when compiling with ELDK-5.2.1 for MIPS64: cmd_bdinfo.c: In function 'print_lnum': cmd_bdinfo.c:56:2: warning: format '%llX' expects argument of type 'long long unsigned int', but argument 3 has type 'u64' [-Wformat] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-10-15input: Add debugging for key matrix key codesSimon Glass
These are read from the fdt - add a debug feature to display the mapping on start-up. See that we get debug output listing the keycodes Signed-off-by: Simon Glass <sjg@chromium.org>
2012-10-15input: Allow key ghosting filter to be disabledSimon Glass
Some keyboards will not need a key ghosting filter, so make this feature optional. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v0.10.2 at 2024-11-09 20:27:49 (GMT)