| Age | Commit message (Collapse) | Author |
|---|
|
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch
WE would like this to become part of the u-boot GIT as well
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Remove unused read_spareram and add unlock_all as kernel does
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Add KB9202 NAND driver
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
Change %08lX to %08X in board.c. Remove unused variable
'oscillator' in mcf5227x/cpu_init.c and 'scm2' in
mcf532x/cpu_init.c. Provide argument type cast in
drivers/dma/MCD_dmaApi.c.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The compile error was caused by a recent patch. Affected platforms -
M5253DEMO.h, M5253EVBE.h, and M54455EVB.h. Adding the _IO_BASE
automatically defined to 0 in asm-m68k/io.h if it isn't set in
platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
see http://www.jedec.org/download/search/jep106Z.pdf
Add some second source legacy flash chips 256x8.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
|
|
|
|
complete
if you don't have firmware installed for the PHY to come to life, this
wait can be painful - let's give the option to avoid it if we want.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Optionally add RFC 2349 "Transfer Size Option", so we can minimize the
time spent sending data over the UART (now print a single line during a
tftp transfer).
- If turned on (CONFIG_TFTP_TSIZE), U-Boot asks for the size of the file.
- if receives the file size, a single line (50 chars) are printed.
one hash mark == 2% of the file downloaded.
- if it doesn't receive the file size (the server doesn't support RFC
2349, prints standard hash marks (one mark for each UDP frame).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Add a simple print for the Blackfin's Ethernet Rx function,
so we can debug incomming Ethernet functions easier.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
This chooses 4kB data size for both TFTP and NFS, as an example
about how to use support for IP fragments.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
To take advantage of defragmented packets, the config file
can define CONFIG_NFS_READ_SIZE to override the 1kB default.
No support is there for an environment variable by now.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Increasing the block size is useful if CONFIG_IP_DEFRAG is
used. Howerver, the last fragments in a burst may overflow the
receiving ethernet, so the default is left at 1468, with thre new
CONFIG_TFTP_BLOCKSIZE for config files. Further, "tftpblocksize"
can be set in the environment.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The defragmenting code is enabled by CONFIG_IP_DEFRAG; the code is
useful for TFTP and NFS transfers. The user can specify the maximum
defragmented payload as CONFIG_NET_MAXDEFRAG (default 16k).
Since NFS has a bigger per-packet overhead than TFTP, the static
reassembly buffer can hold CONFIG_NET_MAXDEFRAG + the NFS overhead.
The packet buffer is used as an array of "hole" structures, acting as
a double-linked list. Each new fragment can split a hole in two,
reduce a hole or fill a hole. No support is there for a fragment
overlapping two diffrent holes (i.e., thre new fragment is across an
already-received fragment).
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Fix ECC Correction bug where the byte offset location were double
flipped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the s1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byteoffs = (s1 << 0) & 0x80;
.
.
byteoffs |= (s0 >> 4) & 0x08;
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Support USB on PSC3 on the mpc5200. Before this patch, enabling USB support
would reconfigure PSC4 and PSC5 to USB. The mpc5200 does not support USB
enabled on both the standard USB port and PSC3. This patch masks the
appropriate bits when enabling USB.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Remy Bohmer <linux@bohmer.net>
|
|
This RTC is used in some Calao boards. The driver code is taken from
the linux rtc-m41t94 driver
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
|
|
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
In the process, also remove backward-compatiblity macros BIN_TO_BCD and
BCD_TO_BIN and update the sole board using them to use the new bin2bcd
and bcd2bin instead
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
Add support for the DEKA Research and Development galaxy5200 board
The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
|
|
Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED
manually. While it is useful to have this available to the build system,
let's do it automatically rather than forcing people to opt into it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Now that we have sha1 and md5 in lib_generic, allow people to use
them on the command line, for checking downloaded files.
Signed-off-by: Robin Getz <rgetz@analog.com>
|
|
The SPI controller on the S3C24X0 has 8 bit registers, not 32 bit.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Newer revisions of these boards have slightly larger flashes, so increase
the configured number of sectors so that U-Boot works on all revisions.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Start a common header file for common linker script code (such as
workarounds for older linkers) rather than doing this in the build system.
As fallout, we no longer execute the linker every time config.mk is
included by a build file (which can easily be 70+ times), but rather only
execute it once.
This also fixes a bug in the major version checking by creating a macro to
easily compare versions and keep people from making the same common
mistake (forgetting to check major and minor together).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common code preprocesses the linker script, the Blackfin code
no longer needs to do it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
|
|
Update CHANGELOG, minor Coding Style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@petalogix.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
|
|
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot
at either:
NET: Registered protocol family 16
or the
io scheduler cfq registered
message. Fixing up these DDR settings appears to fix the problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
commit 9993e196da707a0a1cd4584f1fcef12382c1c144 "mpc83xx: convert all
remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on
tqm834x to make it more consistent with the other 83xx boards. During
that time however, the author failed to realize that FLASH_BASE was
occupying the same range as what PCI1_MEM_BASE was being assigned.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This was introduced with the MPC8349EMDS board, and then copied to
a couple other boards by nature of being the reference implementation.
u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP
include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
u-boot$
It currently isn't used, so delete it before it spreads further.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This patch fixes some issues with JFFS2 summary support in U-Boot.
1/ Summary support made compilation configurable (as summary support
considered expiremental even in Linux).
2/ Summary code can do unaligned 16-bit and 32-bit memory accesses.
We need to get data byte by byte to exclude data aborts.
3/ Make summary scan in two passes so we can safely fall back to full
scan if we found unsupported entry in the summary.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
|
|
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
The TRAB board references local libgcc helper routines
(lib_arm/div0.o and lib_arm/_umodsi3.o) which cause build problems
when we try to use the normal, compiler provided libgcc instead.
Removing these references allows to build both with and without the
local libgcc helper routines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
