summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-11-13i2c, omap1510: remove i2c driverHeiko Schocher
remove omap1510 i2c driver, as there is no board which uses it Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Jian Zhang <jzhang@ti.com>
2013-11-13i2c, zynq: convert zynq i2c driver to new multibus/multiadapter frameworkHeiko Schocher
- add zync i2c driver to new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com>
2013-11-13i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher
- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13i2c: mxs_i2c: Squash endless loopMarek Vasut
The endless waiting for a bit to be set can cause a hang, add a timeout so we prevent such situation. A testcase for such a hang is below. The testcase assumes a device to be present at address 0x50 and a device to NOT be present at address 0x42 . Also note that the "sleep 1" induced delays are imperative for this bug to manifest . i2c read 0x42 0x0.2 0x10 0x42000000 ; sleep 1 ; \ i2c read 0x50 0x0.2 0x10 0x42000000 ; sleep 1 ; \ i2c read 0x42 0x0.2 0x10 0x42000000 The expected result of the above command is: Error reading the chip. Error reading the chip. While without this patch, we observe a hang in the last read from 0x42 precisely when waiting for this bit to be set. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2013-11-13i2c: sh_i2c: Update to new CONFIG_SYS_I2C frameworkNobuhiro Iwamatsu
This updates to new I2C framwwork on sh_i2c. And this also updates boards(kzm9g and ecovec) that using sh_i2c. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-11-12cm_t35: use scf0403 driverNikita Kiryanov
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730 boards. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-12omap3_dss: define DSS_ONOFFNikita Kiryanov
Add DSS_ONOFF to polarity defines Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Anatolij Gustschin <agust@denx.de>
2013-11-12lcd: add DataImage SCF0403x LCD panel supportNikita Kiryanov
Add SPI-based driver for DataImage SCF0403852GGU04 and SCF0403526GGU20 LCD panels. Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-11-12spi: define SPI_XFER_ONCENikita Kiryanov
The flag combination "SPI_XFER_BEGIN | SPI_XFER_END" is a common use case of spi_xfer, and it can easily cause an already long line (spi_xfer takes 5 parameters) to go over the 80 character limit. define SPI_XFER_ONCE to be a shorter version of the above flag combination. Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-12spi: omap3: add support for more word lengthsNikita Kiryanov
Current implementation only supports 8 bit word lengths, even though omap3 can handle anything between 4 and 32. Update the spi interface to support changing the SPI word length, and implement it in omap3_spi driver to support the full range of possible word lengths. This implementation is backwards compatible by defaulting to the old behavior of 8 bit word lengths. Also, it required a change to the omap3_spi non static I/O functions, but since they are not used anywhere else, no collateral changes are required. Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-12spi: omap3: remove semicolon from #defineNikita Kiryanov
Remove unnecessary semicolon from #define SPI_WAIT_TIMEOUT Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Gerhard Sittig <gsi@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-12video: bcm2835: respect the pitch valueAndre Heider
Depending on the firmware's video options [1] the active SDTV or HDTV mode can yield a framebuffer with noncontiguous horizontal lines, giving a messed up display, for both, u-boot and the loaded kernel. Fix this by setting lcd_line_length to the pitch value of the configured framebuffer. [1] http://elinux.org/RPiconfig#Video_mode_options Signed-off-by: Andre Heider <a.heider@gmail.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2013-11-12lcd: allow overriding lcd_get_size()Anatolij Gustschin
Remove the redundant lcd_line_length initialisation which sneaked in when an earlier version of the patch of commit 6d330719 has been rebased. Some lcd drivers need to setup lcd_line_length not from the panel_info parameters but by different means. Make the lcd_get_size() weak to allow setting lcd_line_length in a driver specific way. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-11-12ARM: bcm2835: add missing mbox overscan response fieldAndre Heider
Add the missing "right" field to struct bcm2835_mbox_tag_overscan. Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-11-11MPC824x: remove obsolete "PN62" boardWolfgang Denk
The MPC824x processors have long reached EOL, and the PN62 board has not seen any board-specific updates for more than a decade. It is now causing build issues. Instead of wasting time on things nobody is interested in any more, we rather drop this board. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com> cc: Tom Rini <trini@ti.com>
2013-11-11time: fix gcc warnings on MIPS64Daniel Schwierzeck
Commit 8dfafdde88eb3e71d5569846396ae67a91017232 introduced new gcc warnings on MIPS64: time.c: In function 'tick_to_time': time.c:59:2: warning: comparison of distinct pointer types lacks a cast [enabled by default] time.c:59:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default] In file included from time.c:10:0: ./u-boot-mips/include/div64.h:22:17: note: expected 'uint64_t *' but argument is of type 'long long unsigned int *' time.c: In function 'usec_to_tick': time.c:76:2: warning: comparison of distinct pointer types lacks a cast [enabled by default] time.c:76:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default] In file included from time.c:10:0: ./u-boot-mips/include/div64.h:22:17: note: expected 'uint64_t *' but argument is of type 'long long unsigned int *' Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-11-11Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
2013-11-11malta: arch/mips/include/asm/malta.h SPDX license tagPaul Burton
This patch replaces the GPL-2.0 text with a GPL-2.0 SPDX-License-Identifier tag, and adds Imagination Technologies copyright following my recent changes. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
2013-11-09malta: define CONFIG_MEMSIZE_IN_BYTESGabor Juhos
The memsize environment variable must contain the memory size in bytes on the Malta board. Otherwise Linux will use wrong memory size which causes a kernel panic. Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid that. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: add myself to maintainersPaul Burton
This patch adds me as a maintainer of the malta(el) board(s). I have access to physical Malta boards and the desire for U-boot to run well on them. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: add script & instructions to flash U-bootPaul Burton
This patch adds a script which may be used with MIPS Navigator Console and a MIPS Nagivator Probe in order to flash U-boot to a MIPS Malta development board. Please see the newly added doc/README.malta for usage instructions. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: setup PIIX4 interrupt routePaul Burton
Without setting up the PIRQ[A:D] interrupt routes, PCI interrupts will be left disabled. Linux does not set up this routing but relies upon it having been set up by the bootloader, reading back the IRQ lines which the PIRQ[A:D] signals have been routed to. This patch routes PIRQA & PIRQB to IRQ 10, and PIRQC & PIRQD to IRQ 11. This matches the setup used by YAMON. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: store environment in flashPaul Burton
Allow the environment to be stored in the monitor flash of a Malta board. The environment is stored in the final 128KB of the flash, which both leaves the majority of the flash available for U-boot code and also matches the location which YAMON uses. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: enable RTC supportPaul Burton
This is actually required in order for a Linux kernel to boot successfully on a physical Malta board. Without enabling the RTC, a Malta Linux kernel will get stuck in its estimate_frequencies function on boot. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: disable L2 cachesPaul Burton
Malta boards may be used with cores which support L2 caches, however U-boot does not yet support L2 cache for MIPS. Thus for the moment we'll disable L2 caches by setting the L2B bit in Config2. This is specific to MTI/Imagination MIPS cores which is why this is done for the Malta board rather than generically. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: remove cache size definitionsPaul Burton
These will now be detected at runtime, allowing a single U-boot configuration to function correctly with different bitstreams. Without this you may need to re-configure, re-build and re-flash U-boot to your Malta if you flash a new bitstream with a different cache configuration to your old bitstream. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: enable CONFIG_PCNET_79C973, PCNET_HAS_PROM, CONFIG_CMD_DHCPPaul Burton
This model of the pcnet is used in current Malta boards, at least in the Malta-R rev 3. Enable support for it. The Malta also has the ethernet controller PROM containing its MAC address, so enable support for that in order to read that MAC address. DHCP is a very useful feature to have available for many networks, enable support for it also. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: display "U-boot" on the LCD screenPaul Burton
Displaying a message on the LCD screen is a simple yet effective way to show the user that the board has booted successfully. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: support for coreFPGA6 boardsPaul Burton
This patch adds support for running on Malta boards using coreFPGA6 core cards, including support for the msc01 system controller used with them. The system controller is detected at runtime allowing one U-boot binary to run on a Malta with either. Due to the PCI I/O base differing between Maltas using gt64120 & msc01 system controllers, the UART setup is modified slightly. A second UART is added so that there is one pointing at the correct address for each system controller. The Malta board then defines its own default_serial_console function to select the correct one at runtime. The incorrect UART will simply not function. Tested on: - A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both with and without an L2 cache. - QEMU. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: setup super I/O UARTsPaul Burton
On a real Malta the Super I/O needs to be configured before we are able to access the UARTs. This patch performs that configuration, setting up the UARTs in the same way that YAMON would. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09qemu-malta: rename to just "malta"Paul Burton
This is in preparation for adapting this board to function correctly on a physical MIPS Malta board. The board is moved into an "imgtec" vendor directory at the same time in order to ready us for any other boards supported by Imagination in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pci.h: allow inclusion in assembly sourcePaul Burton
This patch simply #ifdef's out the C-specific parts of pci.h when it is included by an assembly file. This will allow the macros it contains to be used from assembly source as will be done in a followup commit adding support for more modern MIPS Malta boards. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pcnet: enable the NOUFLO featurePaul Burton
On relatively slow boards (such as the MIPS Malta with an FPGA core card) it can be extremely common for transmits to underflow - to the point where it appears they simply do not work at all. Setting the NOUFLO bit causes the ethernet controller to not begin transmission on the wire until a transmit start point is reached. Setting that transmit start point to the full packet will cause the controller to only transmit the packet once it has buffered it entirely thus preventing any transmit underflows from occuring and allowing the controller to function on slower boards. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pcnet: add cache flushing & invalidationPaul Burton
Ensure that the view of memory from the CPU & the ethernet controller is coherent at the various points where they exchange data. This prevents stale data from being transmitted or received, and prevents the driver from getting stuck waiting for the ethernet controller to update descriptors when in reality it has but the old values are being read from cache. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pcnet: s/le16_to_cpu/cpu_to_le16/ in pcnet_sendPaul Burton
This should cause no change to the generated code, but is semantically correct. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pcnet: code style cleanupPaul Burton
Fix up the code to match Documentation/CodingStyle. This is mostly removing extraneous spaces. No functional change is intended. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09mips32: detect L1 cache sizes if they're not definedPaul Burton
For boards such as the MIPS Malta with an FPGA core card it is desirable to be able to detect the L1 cache sizes at runtime, since they are not dependant upon the board but on the FPGA bitstream in use. This patch performs that detection when the CONFIG_SYS_[DI]CACHE_SIZE macros are not defined by the board configuration. In cases where the sizes are detected this patch also removes the restriction that the I-cache & D-cache line sizes must be the same, as this is not necessarily true. If the cache sizes are defined by a configuration then they will be hardcoded as before, so this patch will not add overhead to such boards. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-08Merge branch 'master' of git://www.denx.de/git/u-boot-usbTom Rini
2013-11-08sandbox: convert to common time functionsRob Herring
Convert sandbox to use common time functions. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08time: add weak annotation to timer_read_counter declarationRob Herring
A weak annotation is needed in order to prevent link errors when get_ticks is overridden. This fixes sandbox build. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08netconsole loses 2nd character of inputSuriyan Ramasami
Netconsole loses the second character when used as input by either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX Before a nc_send_packet() to echo the input, a check is done to see if nc_ether is valid. If its not, it waits for an arp request and then sends the packet (which contains the first character of line to be displayed as output). As part of reaping the arp request, the second character is consumed. We protect this by making the call to NetLoop(NETCONS) between input_recursion. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-11-08serial: s5p: Staticize local functionsAxel Lin
Staticize local functions in s5p serial driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-11-08env: fix the env export varnamePierre Aubert
The env export command doesn't export the first variable of the list since commit 5a31ea04c9ee5544fbb70ad7597ea4b294840eab "env grep" - reimplement command using hexport_r() Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
2013-11-08highbank: set AUTOBOOT_KEYED_CTRLC config optionMark Langsdorf
Let highbank users break into the autoboot script with ctrl-c. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08autoboot: add an option to override keyed autobootMark Langsdorf
As originally implemented, setting the AUTOBOOT_KEYED config option will prevent users from breaking into the autoboot script with ctrl-c. Restore that option with a new config symbol. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08serial: xuartlite: Staticize local functionsAxel Lin
Staticize local functions in xuartlite driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stefan Roese <sr@denx.de> Tested-by: Michal Simek <monstr@monstr.eu>
2013-11-08serial: mxs_auart: Staticize local functionsAxel Lin
Staticize local functions in mxs_auart driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marek Vasut <marex@denx.de>
2013-11-08fs:fat: fix set file name functionPiotr Wilczek
Curently memcpy copies string without null terminating char because function strlen returns only number of characters excluding null terminating character. Replace memcpy with strcpy. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Tom Rini <trini@ti.com>
2013-11-08cmd_zfs: normalize 'file not found' errorsLuka Perkov
Signed-off-by: Luka Perkov <luka@openwrt.org>