summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-07-09dm: spi: Read default speed and mode values from DTVignesh R
In case of DT boot, don't read default speed and mode for SPI from CONFIG_*, instead read from DT node. This will make sure that boards with multiple SPI/QSPI controllers can be probed at different bus frequencies and SPI modes. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHzVignesh R
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better throughput. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2g_evm_defconfig: Enable Cadence QSPI controllerVignesh R
Enable Cadence QSPI controller support to use QSPI on K2G SoC. Also enable Spansion flash support to access s25fl512s flash present on K2G QSPI bus. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: K2G: Add support for QSPI controllerVignesh R
K2G SoC has a Cadence QSPI controller to communicate with NOR flash devices. Add DT nodes to support the same. Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor flash slave node for the same. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09spi: cadence_quadspi: Enable QUAD mode based on DT dataVignesh R
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD mode, make use of mode_rx field of dm_spi_slave_platdata to determine whether to enable or disable QUAD mode. This is necessary to support muliple SPI controllers where one of them may not support QUAD mode. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09spi: cadence_qspi_apb: Support 32 bit AHB addressVignesh R
AHB address can be as long as 32 bit, hence remove the CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT and read as u32 value, it anyway does not make sense to mask upper bits. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2g_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2G SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: k2g: add support for Davinci SPI controllerVignesh R
K2G SoC has 4 SPI instances that are compatible with davinci_spi controller(present on previous generation of Keystone2 devices). Add DT nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on SPI-1. Add DT bindings for the same. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2l_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2L SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: k2l: Enable Davinci SPI controllerVignesh R
Now that davinci_spi driver has been converted to DM framework, enable the same in DT. Also add "spi-flash" as compatible property to n25q128a11 node as it is required for flash device to be probed in U-Boot. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2e_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2E SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: k2e: Enable Davinci SPI controllerVignesh R
Now that davinci_spi driver has been converted to DM framework, enable the same in DT. Also add "spi-flash" as compatible property to n25q128a11 node as it is required for flash device to be probed in U-Boot. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09defconfig: k2hk_evm_defconfig: enable SPI driver modelVignesh R
Enable SPI and SPI Flash driver model as K2HK SPI controller driver supports driver model. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: k2hk: Enable Davinci SPI controllerVignesh R
Now that davinci_spi driver has been converted to DM framework, enable the same in DT. Also add "spi-flash" as compatible property to n25q128a11 node as it is required for flash device to be probed in U-Boot. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09ARM: dts: keystone2: add SPI aliases for davinci SPI nodesVignesh R
Add aliases for SPI nodes in order for it to be probed by the DM framework. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09keystone2: spi: do not define DM_SPI and DM_SPI_FLASH for SPL buildVignesh R
Since Keystone2 devices do not have support DM in SPL, do not define DM_SPI and DM_SPI_FLASH for SPL build. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09spi: davinci_spi: Convert to driver to adapt to DMVignesh R
Convert davinci_spi driver so that it complies with SPI DM framework. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09dm: core: implement dev_map_physmem()Vignesh R
This API helps to map physical register addresss pace of device to virtual address space easily. Its just a wrapper around map_physmem() with MAP_NOCACHE flag. Signed-off-by: Vignesh R <vigneshr@ti.com> Suggested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-07-06spi: spi-uclass: fix typo in debug outputAnatolij Gustschin
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-04Merge git://git.denx.de/u-boot-arcTom Rini
2016-07-04arc: make global_data.h usable in assembly filesAlexey Brodkin
Currently on attempt to use global_data.h in an assembly file following will happen: -------------------->8----------------- ./arch/arc/include/asm/global_data.h: Assembler messages: ./arch/arc/include/asm/global_data.h:11: Error: bad instruction 'struct arch_global_data{' ./arch/arc/include/asm/global_data.h:12: Error: junk at end of line, first unrecognized character is `}' scripts/Makefile.build:316: recipe for target 'arch/arc/lib/start.o' failed -------------------->8----------------- In this change we disable struct arch_global_data in ASM which fixes the issue above. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-04arc: Use "-mcpu=archs" instead of deprecated "-marchs" for ARC HSAlexey Brodkin
Newer ARC toolchains don't support "-marchs" option any longer. Instead "-mcpu=archs" should be used. What's also important older toiolchains that support ARC HS cores will also happily accept "-mcpu=archs" so that's a very safe move. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-02Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-07-02sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)Quentin Schulz
The Parrot Board is an evaluation board with an Allwinner R16 (assumed to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2 controllable buttons, an LVDS port with separated backlight and capacitive touch panel ports, an audio/microphone jack, a camera CSI port, 2 sets of 22 GPIOs and an accelerometer. The DTS file is identical to the one submitted to the upstream kernel. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-02sunxi: Add missing boot_media fields in the SPL headerOlliver Schinagl
Commit b19236fd1 ("sunxi: Increase SPL header size to 64 bytes to avoid code corruption") Added defines for MMC0 and SPI as boot identification. After verifying on an OLinuXino Lime2 with NAND and eMMC, the expected values have been confirmed and added to spl.h Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-02sunxi: spl: Fix DRAM info printingHans de Goede
The switch to simple_printf was causing the SPL dram info to show as: DRAM: u MiB This fixes this by switching from %lu to %d for printing the DRAM size. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-02Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2016-07-02Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2016-07-01Prepare v2016.07-rc3Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-01Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2016-07-01mmc: increase MMC SDHCI read status timeoutSteve Rae
Otherwise, ocassionally see errors like this: Flashing sparse image at offset 2078720 Flashing Sparse Image sdhci_send_command: Timeout for status update! mmc fail to send stop cmd write_sparse_image: Write failed, block #2181088 [0] This does not affect the actual writing speed, which is controlled by the default value: CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT It only increases the retries when reading: SDHCI_INT_STATUS to avoid the timeout error. Signed-off-by: Steve Rae <steve.rae@raedomain.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-07-01ti_omap5_common: Find right dtb file for DRA72-RevC EvmLokesh Vutla
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-07-01autoboot: move bootdelay >= 0 check to abortboot()Masahiro Yamada
Move the bootdelay >= 0 check to the caller, which simplifies the callees. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01autoboot: move CONFIG_SILENT_CONSOLE handlingMasahiro Yamada
Factor out the same code from the callees to the caller. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01autoboot: rename abortboot_{keyed, normal} to __abortbootMasahiro Yamada
Because abortboot_keyed() and abortboot_normal() are not compiled at the same time, we can rename both of them to __abortboot(). This allows to drop #ifdef from the caller. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECKMasahiro Yamada
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2 means the autoboot with no delay, with no abort check even if CONFIG_ZERO_BOOTDELAY_CHECK is defined. To sum up, the autoboot behaves as follows: [1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y autoboot with no delay, but you can abort it by key input [2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n autoboot with no delay, with no check for abort [3] CONFIG_BOOTDELAY=-1 disable autoboot [4] CONFIG_BOOTDELAY=-2 autoboot with no delay, with no check for abort As you notice, [2] and [4] come to the same result, which means we do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the cases only by CONFIG_BOOTDELAY, like this: [1] CONFIG_BOOTDELAY=0 autoboot with no delay, but you can abort it by key input [2] CONFIG_BOOTDELAY=-1 disable autoboot [3] CONFIG_BOOTDELAY=-2 autoboot with no delay, with no check for abort This commit converts the logic as follow: CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n --> CONFIG_BOOTDELAY=-2 Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Heiko Schocher <hs@denx.de> Acked-by: Christian Riesch <christian.riesch@omicronenergy.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2016-07-01doc: bootdelay: drop explanation about CONFIG_BOOTDELAY from READMEMasahiro Yamada
The same information now exists in common/Kconfig. Do not duplicate documentation from the point of view of maintainability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2016-07-01ARM: socfpga: move CONFIG_BOOTDELAY to Kconfig for IS1 boardMasahiro Yamada
This recently added board missed the tree-wide migration of CONFIG_BOOTDELAY. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Pavel Machek <pavel@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2016-07-01ARM: AM437x: Align HS device variant defconfig filenameAndreas Dannenberg
Align the name of the defconfig file for high-security (HS) device variants from the AM43xx family of SoCs with the corresponding name used for the general purpose devices. This allows for easier cross-association of those files and also provides room to grow from an HS device part number perspective. Furthermore, update and cleanup associated MAINTAINERS file. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Madan Srinivas <madans@ti.com>
2016-07-01driver: qspi: correct QSPI disable CS reset valuePraneeth Bajjuri
Correcting QSPI disable/unselect CS reset value. CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8] This is not causing any issue, but its better to untouch the reserved bits. Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Ravi Babu <ravibabu@ti.com>
2016-07-01ARM: uniphier: add external IRQ setup codeMasahiro Yamada
I will carry this work-around until it is cared in the kernel. This looks up the AIDET node and sets up a register to handle active low interrupt signals. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01ARM: dts: uniphier: add AIDET nodesMasahiro Yamada
The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of syscon block related with the interrupt controller. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01pinctrl: uniphier: add Ethernet pin-mux settingsMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01pinctrl: uniphier: avoid building unneeded pin-mux tables for SPLMasahiro Yamada
SPL does not use all of the devices, so we can save some memory footprint. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01pinctrl: uniphier: support pin configuration for dedicated pinsMasahiro Yamada
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration (pin biasing, drive strength control), but not pin-muxing. Allow to fill the mux value table with -1 for those pins; pins with mux value -1 will be skipped in the pin-mux set function. The mux value type should be changed from "unsigned" to "int" in order to accommodate -1 as a special case. [ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20Masahiro Yamada
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I added a single driver shared between them in the initial commit. However, the Ethernet pin-mux settings I am going to add are different with each other, and they may diverge more as the progress of development. Split it into two dedicated drivers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01pinctrl: uniphier: allow to have pinctrl node under syscon nodeMasahiro Yamada
Currently, the UniPhier pinctrl driver itself is a syscon, but it turned out much more reasonable to make it a child node of a syscon because our syscon node consists of a bunch of system configuration registers, not only pinctrl, but also phy, and misc registers. It is difficult to split the node. This commit allows to migrate to the new DT structure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-01ARM: dts: uniphier: sync Device Trees with upstream LinuxMasahiro Yamada
I periodically sync Device Trees for better maintainability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30pinctrl: uniphier: remove unneeded pin group nand_cs1Masahiro Yamada
This SoC does not support NAND CS1. This place-holder is no longer necessary. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20Masahiro Yamada
My mistake in the initial support patch. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v0.10.2 at 2024-10-14 19:52:29 (GMT)