summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-05-15LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSIDonghwa Lee
This patch support S6E8AX0 amoled driver based on EXYNOS MIPI DSI interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: support EXYNOS MIPI DSI interface driver.Donghwa Lee
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI based LCD Panel could be used with it. This patch supports MIPI-DSI driver based Samsung SoC chip. LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at board file and LCD panel driver specific function registered to mipi_dsim_ddi structure at lcd panel init function called system init. In the MIPI-DSI driver, find lcd panel driver by using registered lcd panel name, and then initialize lcd panel driver. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: support EXYNOS framebuffer and FIMD display drivers.Donghwa Lee
This patch support EXYNOS FB and FIMD display drivers. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15LCD: add data structure for EXYNOS display driverDonghwa Lee
Add vidinfo data structure for EXYNOS display driver Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: add LCD and MIPI DSI clock interface.Donghwa Lee
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: definitions of system resgister and power management registers.Donghwa Lee
This is definitions of system registers and power mananagement registers for EXYNOS SoC. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15SMDK5250: fix compiler warningMinkyu Kang
this patch fixed following warning. tzpc_init.c: In function 'tzpc_init': tzpc_init.c:35: warning: assignment from incompatible pointer type Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
2012-05-15misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998Łukasz Majewski
TRATS target uses MAX8997 PMIC device instead of MAX8998. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15misc:pmic:max8997 MAX8997 support for PMIC driverŁukasz Majewski
This commit adds support for MAX8997 PMIC driver. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15TRATS: modify the trats's configurationJaehoon Chung
Trats is supported 1GiB memory size. (Each bank size is 512MB.) And INITRD is unnecessary. So removed them. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurementŁukasz Majewski
This patch enables LDO4 power line for preparing proper voltages to be measured by ADC converter. This measurement is used for determination of target board HW revision. Test HW: Universal_C210 (Exynos4210) rev. 0.0 Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: Rename exynos5_tzpc structure to exynos_tzpcChander Kashyap
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic usase of tzpc. Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INITNobuhiro Iwamatsu
With almost all the architecture and board BOARD_LATE_INIT does not use. CONFIG_BOARD_LATE_INIT is used instead. This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INITNobuhiro Iwamatsu
With almost all the architecture and board BOARD_LATE_INIT does not use. CONFIG_BOARD_LATE_INIT is used instead. This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2012-05-15cm-t35: add I2C multi-bus supportNikita Kiryanov
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15include/configs: Remove CONFIG_SYS_64BIT_STRTOULTom Rini
This define does not control anything, remove it. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15include/configs: Remove CONFIG_SYS_64BIT_VSPRINTFTom Rini
This define does not control anything, remove it. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap3: Introduce weak misc_init_rTom Rini
Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15omap730p2: Remove empty misc_init_rTom Rini
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap5912osk: Remove empty misc_init_rTom Rini
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap4+: Remove CONFIG_ARCH_CPU_INITTom Rini
OMAP4/5 had an empty arch_cpu_init() so drop that along with CONFIG_ARCH_CPU_INIT Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap4: Remove CONFIG_SYS_MMC_SET_DEVTom Rini
This is only used on !CONFIG_GENERIC_MMC which is false here. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP3: pandora: drop console kernel argumentGrazvydas Ignotas
As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial cables are not widespread, simply drop console argument. This should allow booting old and new kernels with default arguments, and those who need serial can use a boot script on SD card. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15OMAP3: pandora: revise GPIO configurationGrazvydas Ignotas
Update pandora's GPIO setup code with these changes: - convert to gpiolib - set up dual voltage GPIOs to match supply of 1.8V by clearing VMODE1 - add GPIO_IO_PWRDNZ configuration for DM3730 variation of pandora (required to enable GPIO 126, 127, and 129 I/O cells in DM3730) - add wifi reset pulse as recommended by wifi chip's manufacturer - drop configuration of GPIOs that u-boot doesn't need Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15OMAP3: pandora: pin mux updates for DM3730 board variantGrazvydas Ignotas
DM3730 needs some additional pin mux configuration for GPIOs 126-129 to work, add it. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15Makefile: Add a 'checkthumb' ruleTom Rini
This rule confirms that if we're on ARM and we have enabled THUMB builds that we have a new enough toolchain to produce a working binary. Changes in v2: - Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F) - Simplfy checkthumb test after doing the above Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15tools, config.mk: Add gcc-version.sh, cc-version test from LinuxTom Rini
Added from Linux - commit fde7d9049e55ab85a390be7f415d74c9f62dd0f9 Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP4: enable Thumb buildAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15omap4+: Avoid using __attribute__ ((__packed__))Aneesh V
Avoid using __attribute__ ((__packed__)) unless it's absolutely necessary. "packed" will remove alignment requirements for the respective objects and may cause alignment issues unless alignment is also enforced using a pragma. Here, these packed attributes were causing alignment faults in Thumb build. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15armv7: Use -march=armv7-a and thereby enable Thumb-2Aneesh V
Enable -march=armv7-a for armv7 platforms if the tool-chain supports it. This in turn results in Thumb-2 code generated for these platforms if CONFIG_SYS_THUMB_BUILD is enabled. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15ARM: enable Thumb buildAneesh V
Enable Thumb build and ARM-Thumb interworking based on the new config flag CONFIG_SYS_THUMB_BUILD Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15armv7: add appropriate headers for assembly functionsAneesh V
Use ENTRY and ENDPROC with assembly functions to ensure necessary assembler directives for all functions. Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15arm: adapt asm/linkage.h from LinuxAneesh V
This will add ARM specific over-rides for the defines from linux/linkage.h Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15OMAP5: reset: Use cold reset in case of 5430ES1.0SRICHARAN R
Warm reset is not functional in case of omap5430ES1.0. So override the weak reset_cpu function to use cold reset instead. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP3+: reset: Create a common reset layer.SRICHARAN R
The reset.S has the function to do a warm reset on OMAP based socs. Moving this to a reset.c file so that this acts a common layer to add any reset related functionality for the future. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15mmc: omap5evm: Add eMMC saveenv supportBalaji T K
Save env to eMMC Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15omap5: pbias ldo9 turn onBalaji T K
Add omap5 pbias configuration for mmc1/sd lines and set voltage for sd data i/o lines Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15power: twl6035: add palmas PMIC supportSRICHARAN R
palmas/TWL6035 is power IC for omap5 evm boards Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15arm: omap5: correct boot device mode7 for eMMCBalaji T K
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP4/5: emif: Correct the emif power mgt shadow register bit fields.SRICHARAN R
PD_TIM bit field which specifies the power down timing is defined to occupy bits 8-11, where as it is actually from 12-15 bits. So correcting this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: ddr: Change the ddr device name.SRICHARAN R
The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and not a ELPIDA part. So change this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: defconfig: Align the defconfig for 5430 ES1.0SRICHARAN R
Adding the nessecary changes for OMAP5430 ES1.0 silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: device: Add support to get the device type.SRICHARAN R
Add support to identify the device as GP/EMU/HS. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the sysctrl structure commonSRICHARAN R
Make the sysctrl structure common, so that it can be used in generic functions across socs. Also change the base address of the system control module, to include all the registers and not simply the io regs. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: SRAM: Change the SRAM base address.SRICHARAN R
The full internal SRAM of size 128kb is public in the case of OMAP5 soc. So change the base address accordingly. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the silicon revision variable common.SRICHARAN R
The different silicon revision variable names was defined for OMAP4 and OMAP5 socs. Making the variable common so that some code can be made generic. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: hwinit: Add the missing break statementSRICHARAN R
The break statement is missing in init_omap_revision function, resulting in a wrong revision identification. So fixing this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: palmas: Configure nominal opp vdd valuesSRICHARAN R
The nominal opp vdd values as recommended for ES1.0 silicon is set for mpu, core, mm domains using palmas. Also used the right sequence to enable the vcores as per a previous patch from Nishant Menon, which can be dropped now. http://lists.denx.de/pipermail/u-boot/2012-March/119151.html Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.SRICHARAN R
The OMAP5 silicon has new DDR PHY design, which includes a external PHY as well. So configuring the ext PHY parameters here. Also the EMIF timimg registers and a couple of DDR mode registers needs to be updated based on the testing from the actual silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: io: Configure the io settings for omap5430 sevm board.SRICHARAN R
The control module provides options to set various signal integrity parameters like the output impedance, slew rate, load capacitance for different pad groups. Configure these as required for the omap5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
generated by cgit v0.10.2 at 2024-09-08 09:45:06 (GMT)