summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-01-11mmc: s5p_sdhci: add the s5p_set_clock functionJaehoon Chung
Add the s5p_set_clock function. It's not good that "set_mmc_clk" is assigned directly. In future, it should be changed to use the clock framework. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: change the set_ios return type from void to intJaehoon Chung
To maintain consistency, set_ios type of legacy mmc_ops changed to int. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: sdhci: remove the SDHCI_QUIRK_NO_CDJaehoon Chung
This quirk doesn't need anymore. It's replaced to get_cd callback function. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: pic32_sdhci: move the code to pic32_sdhci.cJaehoon Chung
This code is used for only pic32_sdhci controller. To remove the "#ifdef", moves to pic32_sdhci.c. And use the get_cd callback function. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: sdhci: remove the unused code about testing Card detectJaehoon Chung
This code is dead code..There is no usage anywhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: sdhci: add the get_cd callback function in sdhci_opsJaehoon Chung
Some SoCs can have their own card dect scheme. Then they may use this get_cd callback function after implementing init in their drivers. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11mmc: sdhci: disable the 8bit mode when host doesn't support itJaehoon Chung
Buswidth is depeneded on Hardware schematic. Evne though host can support the 8bit buswidth, if hardware doesn't support 8bit mode, it doesn't work fine. So the buswidth mode selection leaves a matter in each SoC drivers. On the contrary to this, hardware supports 8bit mode, but host doesn't support it. then controller has to disable the MMC_MODE_8BIT. (Host can check whether 8bit mode is supported or not, since V3.0) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11ARM64: zynqmp: Move CONFIG_AHCI from board fileMichal Simek
Move configuration option from board file to defconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-11xilinx_phy: Pass correct pointer to fdtdec_get_int()Kamensky Ivan
This patch fixes incorrect pointer on offset device in device tree blob. When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII" it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying to change frequency. Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-01-10Merge git://git.denx.de/u-boot-dmTom Rini
2017-01-10mips: Use common _AC macro now.Tom Rini
MIPS no longer needs to have its own version of this macro now. Fixes: 2a6713b09b8d ("move UL() macro from armv8/mmu.h into common.h") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-10Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2017-01-10ARM64: zynqmp: Generate handoff structure for ATFMichal Simek
Xilinx ATF extending options for passing images from BL2(FSBL) to BL31. U-Boot SPL is FSBL replacement that's why it should generate handoff structure the same. Support only one entry which is U-Boot in EL2 itself. When FIT image is adopted structure generate should be data driven. Currently ATF is placing this structure at the beggining of OCM which is rewriting early parts of ATF which should be unused at that time. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10fpga: Use enum for bitstream command typesMichal Simek
Using enum simplify handling of different bitstream command types. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynqmp: Make SYS_VENDOR configurableMike Looijmans
Add a string description for SYS_VENDOR to allow configuring boards from other vendors than just "xilinx". Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Fix i2c node's compatible stringMoritz Fischer
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core which fixes some silicon bugs that needed software workarounds in Version 1.0 that was used on Zynq systems. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10i2c: cdns: Add additional compatible string for r1p14 of the IP.Moritz Fischer
Adding additional compatible string for version 1.4 of the IP block. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10net: zynq_gem: Use clock driver for ZynqMPSiva Durga Prasad Paladugu
Enable and use the clock driver routine defined in clock driver toset required clock appropriately. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10clk: zynqmp: Add clock driver support for zynqmpSiva Durga Prasad Paladugu
Add basic clock driver support for zynqmp which sets the required clock for GEM controller Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-10ARM64: zynqmp: Enable fastboot for first SD/MMC/EMMC deviceSiva Durga Prasad Paladugu
DNL numbers are not changed that's why fastboot needs to be called with -i parameter (Xilinx vendor id). - Show available devices sudo fastboot -i 0x03fd devices xilinx_zynqmp_zcu100 fastboot - Stop fastboot and go back to U-Boot prompt sudo fastboot -i 0x03fd continue - Reboot the board sudo fastboot -i 0x03fd reboot - Get internal variables sudo fastboot -i 0x3fd getvar bootloader-version bootloader-version: U-Boot 2016.07-00026-g19bd53044817 sudo fastboot -i 0x3fd getvar downloadsize downloadsize: 0x06000000 sudo fastboot -i 0x3fd getvar version version: 0.4 (regular variables needs to have fastboot. prefix - there is also serialno variable which should be define as serial#) - Format SD/MMC/EMMC card sudo fastboot -i 0x3fd oem format - Write images to boot and Linux partition sudo fastboot -i 0x3fd flash boot sd.img sudo fastboot -i 0x3fd flash Linux os.img - Creating sd.img or os.img $ dd if=/dev/zero of=sd.img bs=1024 count=1024 $ mkfs.vfat sd.img $ mkdir sd-mount $ mount -o loop sd.img sd-mount $ echo foo > sd-mount/bar $ umount sd-mount partitions setting should be checked by running gpt command. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Add idle state for ZynqMPStefan Krsmanovic
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0 idle state is added in this patch. References to the idle-states node are added in all CPU nodes. Time values: entry/exit latencies and min-residency, needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0 and Extended StateID format. Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: Will Wong <willw@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Fix usb nodes for dc1 and dc2Michal Simek
Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Add missing earlycon for ep108Michal Simek
Just sync between version. Others zynqmp boards have this setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-10ARM64: zynqmp: clk: Add the clock for watchdogShubhrajyoti Datta
The watchdog clock node is missing. Add the same. This solves the below error. cdns-wdt fd4d0000.watchdog: input clock not found cdns-wdt: probe of fd4d0000.watchdog failed with error -2 Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source propertySudeep Holla
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynq: Setup modeboot variable based on boot modeMichal Simek
modeboot variable is used for saving inforation which bootmode is used. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynq: Remove spi-max-frequencyMichal Simek
spi-max-frequency for spi bus depends on devices which are connected to it. Remove this parameter from dtsi file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynq: Remove CONFIG_BOOTP_SERVERIPMichal Simek
Do the same change which was done in ZynqMP by: "ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP" (sha1: a8b6a156c0f7fb99502229e454bc9c3b38645280) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM: zynq: Move CONFIG_SYS_TEXT_BASE to KconfigMichal Simek
Enable CONFIG_SYS_TEXT_BASE via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10fpga: zynqmp: Remove empty functionsMichal Simek
Xilinx core files will take care about it. There is no need to have these functions because they do nothing. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Add support to save env to FATSiva Durga Prasad Paladugu
Add support to save environment as a file of FAT filesystem on to SD card. The file will be saved with name uEnv.txt. This environment will be retrieved during boot. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10ARM64: zynqmp: Increase environment size to 32KSiva Durga Prasad Paladugu
Increase environment size to 32K as the current default environment itself is greater than 4K. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10microblaze: Enable option to overwrite default variablesMichal Simek
Enable overwriting variables out of main config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10microblaze: Remove hardcoded IP address from configMichal Simek
IP addresses shouldn't be hardcoded in board config. This patch removes them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10microblaze: Make the board configuration name user definableSai Pavan Boddu
Add a prompt for editing in menuconfig Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10net: gem: Use wait_for_bit() instead of private mdio_wait()Michal Simek
Using generic wait_for_bit() implementation instead of using private wait function. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10lib: Add WATCHDOG_RESET to wait_bit.hMichal Simek
wait_for_bit() is missing reset watchdog in case watchdog is configured. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-09scsi: dm: Unbind all scsi based block devices before new scanMichal Simek
New scan should unbind all block devices not to be listed again. Without this patch if scsi reset or scan is called new block devices are created which point to the same id and lun. For example: ZynqMP> scsi scan scsi_scan: if_type=2, devnum=0: sdhci@ff170000.blk, 6, 0 scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 0 scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 1 scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 2 scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 3 scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 4 scanning bus for devices... Device 0: (1:0) Vendor: ATA Prod.: KINGSTON SVP200S Rev: 501A Type: Hard Disk Capacity: 57241.8 MB = 55.9 GB (117231408 x 512) Reported-by: Ken Ma <make@marvell.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
2017-01-09defconfig: am335x_evm: enable usb driver modelMugunthan V N
enable usb driver model for am335x bbb as musb supports driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-09am335x_evm: enable usb ether gadget as it supports DM_ETHMugunthan V N
Since usb ether gadget have support for driver model, so enable usb ether gadget. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-09am33xx: board: init usb ether gadget for rndis supportMugunthan V N
Add usb ether gadget device with usb_ether_init() when CONFIG_DM_ETH and CONFIG_USB_ETHER are defined. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-09drivers: usb: gadget: ether/rndis: convert driver to adopt device driver modelMugunthan V N
Adopt usb ether gadget and rndis driver to adopt driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2017-01-09Prepare v2017.01Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-09lib: gitignore *.elf and *.so generated by efi_loaderLadislav Michl
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2017-01-09scripts/config_whitelist.txt: ResyncTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-08mx6ullevk: Add missing MAINTAINERS for mx6ull_14x14_evk_plugin_defconfigJagan Teki
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig which is missing in below commit "imx: mx6ull_14x14_evk: add plugin defconfig" (sha1: b90ebf49bb8f74afe68f696f59a0e24cc79f2031) Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-08am335x: configs: Use ISW_ENTRY_ADDR to set SPL_TEXT_BASEAndrew F. Davis
The SPL load address changes based on boot type in HS devices, ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs for similar reasons. Add this same logic for AM33xx devices. Also make the default value for ISW_ENTRY_ADDR correct for GP devices based on SoC, HS devices already pick the correct value in their defconfig. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-01-08arm: mach-omap2: Fix secure file generationAndrew F. Davis
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was not generated but generate an unsigned one anyway, first fix this warning to say that it was generated but not secured. When the user then exports TI_SECURE_DEV_PKG after getting this warning, and tries to re-build, 'make' will detect the build artifacts as unchanged and so assume they do not need to be re-generated. This causes it to fail to sign the files and it will pack unsigned files into the final image, even though TI_SECURE_DEV_PKG is now correctly defined and working. Fix this by using FORCE on the targets causes them to be re-run even if the dependent files have not changed. This then causes another issue. We currently rename the signed dtb files to overwrite the non-signed ones. We do this so the 'mkimage' tool gives the packaged dtb sections the correct name. If we do not rename the files then SPL will not find them during boot. Fix this by renaming the dtb files by appending _HS to the end of the filename, after the ".dtb", this causes them to still be named correctly in the FIT blob. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-01-05Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2017-01-05Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
generated by cgit v0.10.2 at 2024-08-02 22:47:28 (GMT)