| Age | Commit message (Collapse) | Author |
|---|
|
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This errata a008751 is applied on Soc specific file currently.This will be
moved to a file where all the errata implementation will take place for usb
for fsl. This patch removes the errata workaround from soc specific file
for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This patch does the following things:
1. Makes the errata checking code common for PPC and ARM
2. Moves all these static inline functions into a dedicated C file
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Performs code cleanup for device tree fixup for fsl usb controllers by
making functions to handle these similar errata checking code.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
|
|
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
The Kona PHY supports an 8-bit wide UTMI interface,
therefore, choose this Kconfig setting.
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
writting to ubi nand partitions need after write ends an erase
of the remaining sectors. This fail, if dfu write size was not
a multiple of erasesize, example log:
Failure erase: -1
Fix this error.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
read the ECC Type field from the i2c eeprom, instead
configuring it static in the U-Boot binary.
see RM:
Table 26-17. NAND Geometry Information on I2C EEPROM
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
support in omap_nand_switch_ecc() also an eccstrength
from 16.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
simple detachs ubi from the mtd partition.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
From: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06)
SHC C3-Sample
MPU reference clock runs at 6 MHz
Setting MPU clock to 594 MHz
Enabling Spread Spectrum of 18 permille for MPU
Trying to boot from MMC
reading u-boot.img
reading u-boot.img
U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100)
Watchdog enabled
I2C: ready
DRAM: 512 MiB
reloc off 1f783000
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net: cpsw
U-Boot#
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".
So, add the info to the doc, that there is also
"AM335x ROM" possible.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
make this function weak, so board code can setup in SPL
MMC init with board special values.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
revert patch:
commit: 6b2221b008e0: mmc: Handle switch error status bit in MMC card status
to get eMMC working on shc board
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
show_boot_progress() is now called from SPL also.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add the following defines, needed for the upcoming shc board
support:
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
if CONFIG_VERSION_VARIABLE is set, the U-Boot environment
contains a "vers" variable with the current U-Boot version
string. If now "printenv" is called, test/py fails as it
detects the main_sign string, which is in this case correct.
So check only the main_sign as an error, if CONFIG_VERSION_VARIABLE
is not set.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
This current code passes the variable arguments list to sprintf(). This is
not correct. Fix it by calling _vprintf() directly.
This makes firefly-rk3288 boot again.
Fixes: abeb272 ("tiny-printf: Support snprintf()")
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.
The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Unlike NAND, eMMC can be re-written without erasing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Because setenv() may fail, it is better to check its return code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This function is shared between PH1-LD11 and PH1-LD20. The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
configs/peach-pi_defconfig
configs/peach-pit_defconfig
|
|
Avoid use of hard coded mmcdev value, use bootpart
instead, so finduuid works based on bootpart set
for a specific platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
When setting up a DDR controller it is useful to be able to display
frequencies in a readable form. Make the strmhz() function available in
SPL builds provided there is full vsprintf available.
Reviewed-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
|
|
Since bcopy() is no longer used, delete all remaining references to
it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
|
|
Now that all Keystone2 dts file names are changed in Linux kernel, reflect the
same in evn variables inorder to find the right dtb file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
Some systems are starting to shift to support DM_VIDEO which exposes
the frame buffer through a slightly different interface.
This is a poor man's effort to support the dm video interface instead
of the lcd one. We still only support a single display device.
Signed-off-by: Alexander Graf <agraf@suse.de>
[trini: Remove fb_size / fb_base as they were not used]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When a payload calls our memory allocator with the exact address hint, we
happily allocate memory from completely unpopulated regions. Payloads however
expect this to only succeed if they would be allocating from free conventional
memory.
This patch makes the logic behind those checks a bit more obvious and ensures
that we always allocate from known good free conventional memory regions if we
want to allocate ram.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We introduced special "DEBUG_EFI" defines when the efi loader
support was new. After giving it a bit of thought, turns out
we really didn't have to - the normal #define DEBUG infrastructure
works well enough for efi loader as well.
So this patch switches to the common debug() and #define DEBUG
way of printing debug information.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Some times you may want to exit an EFI payload again, for example
to default boot into a PXE installation and decide that you would
rather want to boot from the local disk instead.
This patch adds exit functionality to the EFI implementation, allowing
EFI payloads to exit.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
There is new strider cpu flavor with DisplayPort video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
There is a new strider console flavor with DisplayPort
video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Limit "osdsize"-command to access valid screens only.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
