| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for the Palm Treo 680 smartphone. A quick overview of
u-boot implementation on the treo 680...
The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device. The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL). At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it. The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image. That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.
The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).
Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen. But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
This stuff has been rotting in the tree for a year now. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The BAB7xx boards are almost deceased. They cause build warnings, an
it's not worth the effort to fix these. Remove the dead body.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
|
|
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Thomas Elste <info@elste.org>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Curt Brune <curt@cucy.com>
|
|
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
|
|
The barco board appears to be unmaintained since it was added about 5
years ago. The environment location has probably never been correct.
Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marc Leeman <marc.leeman@barco.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year. Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
The logodl board has long been unmaintained and left broken.
As obviously nobody is interestedin that code any more, we may as well
remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: August Hoeraendl <august.hoerandl@gmx.at>
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
|
|
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
|
|
Mercury-EP2500.patch
- added Mercury's EP2500 board uses the mcf5282 processor
CREDITS.patch
Signed-off-by: David Wu <davidwu@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
|
|
Signed-off-by: Detlev Zundel <dzu@denx.de>
|
|
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.
Any custom xilinx ppc405 board can be added very easily with no code
duplicity.
This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h
This patch is prepared to work with the latest version of EDK (10.1)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch provides an unificated way of handling xilinx v5 ppc440 boards.
It unificates 3 different things:
1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.
If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).
2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)
3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.
In order to support new boards they can be implemented in the next way:
a) Simple Generic Board (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config
&& make
b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile
c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507
Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:
Cheap board by Avnet for evaluating the Virtex5 FX technology.
This patch adds support for:
- UartLite
- 16MB Flash
- 64MB RAM
Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Conflicts:
MAINTAINERS
|
|
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
|
|
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
ARM: Fix for incorrect version of patch applied when
adding support for the Lyrtech SFF-SDR board.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister, OpenSDR <philip@opensdr.com>
|
|
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
Signed-off-by: Matthew Fettke <mfettke@videon-central.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
|
|
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Kimmo Leppala / Sysart and
Timo Tuunainen / Sysart
|
|
Signed-off-by: Stelian Pop <stelian@popies.net>
|
|
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>
|
|
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
update the CREDITS and MAINTAINERS.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Conflicts:
CREDITS
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
|
|
|
|
|
|
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
This series of patches adds support for 2 boards from Netstal Maschinen.
The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.
The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.
The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.
This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
|
|
Added board/freescale/m5329evb, cpu/mcf532x, drivers/net,
drivers/serial, immap_5329.h, m5329.h, mcfrtc.h,
include/configs/M5329EVB.h, lib_m68k/interrupts.c, and
rtc/mcfrtc.c
Modified CREDITS, MAKEFILE, Makefile, README, common/cmd_bdinfo.c,
common/cmd_mii.c, include/asm-m68k/byteorder.h, include/asm-m68k/fec.h,
include/asm-m68k/io.h, include/asm-m68k/mcftimer.h,
include/asm-m68k/mcfuart.h, include/asm-m68k/ptrace.h,
include/asm-m68k/u-boot.h, lib_m68k/Makefile, lib_m68k/board.c,
lib_m68k/time.c, net/eth.c and rtc/Makefile
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
Reset support
BSP autoconfig support
|
|
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
|
|
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Patch by Aaron Sells, 20 Jun 2006
|
|
Patch by Sangmoon Kim, 18 Aug 2005
|
|
Patch from Richard Danter, 12 Aug 2005
|
