| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
MECP5123 is a MPC5121E based module by esd gmbh.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
|
|
ARIA is a MPC5121E based COM Express module by Dave/DENX.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
|
|
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
|
|
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Zoom2 is a new board from Texas Instruments and LogicPD
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com
This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.
To configure, run
make omap3_zoom2_config
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
|
|
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This is the InterControl custom device based on the MPC5200B chip.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
|
|
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
|
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
|
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
|
|
Add Pandora support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
|
|
Add EVM board support.
Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
|
|
Add Overo board support.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
|
|
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
|
|
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
|
