| Age | Commit message (Collapse) | Author |
|---|
|
Also add a rule to remove demo.bin which was previously leftover
after a "make clean"
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The current files in examples are all standalone application examples,
so put them in their own subdirectory for organizational purposes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Each arch should handle setting a proper default CROSS_COMPILE value in
their own config.mk file rather than having to maintain a large ugly list
in the Makefile. By using conditional assignment, we don't have to worry
about the variable already being set (env/cmdline/etc...).
The common config.mk file takes care of exporting CROSS_COMPILE already,
and while a few variables (toolchain ones) utilize CROSS_COMPILE before
including the arch config.mk, they do so with deferred assignment.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Commit 0a87dd90 that was supposed to fix out-of-tree building for the
pcm030 board was unfortunately incomplete.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Commit c9969947, which added support for the pcm030 board
(aka phyCORE-MPC5200B-tiny), broke out-of-tree building.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
At the first run of make we generate the autoconf.mk and
autoconf.mk.dep if not already the case and we currently include only
to .dep
In order to use these autogenerated values we need to include it also
even if it's included in config.mk but it's done before their
generation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
|
|
|
|
|
|
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
|
|
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
|
|
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
* Remove symlinking of files located outside api_examples/
* Auto generate dependencies for files located outside api_examples/
* Update names of variables to be similar to those in tools/Makefile
* Fix out of tree build error
Dependencies are calculated for all files in the SRCS variable.
Previously, the SRCS variable contained files which were symlinked
into the api_examples/ directory. These symlinked files did not exist
when dependencies were calculated when building out of tree. This
resulted in errors such as:
make[1]: *** No rule to make target `/work/wd/tmp-ppc/api_examples/.depend', needed by `_depend'. Stop.
make[1]: Leaving directory `/home/wd/git/u-boot/work/api_examples'
make: *** [depend] Error 2
Since symlinked source files are no longer used, this bug no longer
exists.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
|
|
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The current kallsyms code is using \\0 to escape the backslash in the awk
code, but the shell too needs escaping. This way we make sure gcc is
passed the \0. Then gcc itself will consume this as an octal, so we have
to use 000 so gcc will create the final NUL.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
currently we need to sync the linker script enty and TEXT_BASE manualy
and the reloc_dst is based on it
instead provide it now from the ldflags
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
|
|
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
|
|
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
|
|
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
|
|
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
|
|
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
The way the ALL variable is used allows for config.mk's to add more
targets themselves without having to clutter up the top level Makefile.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option. So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file. This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
For the most part, the Blackfin processor boots files in the LDR format
rather than binary/ELF files. So we want to export the environment as a
raw blob to the LDR utility so it can embed it at the right location.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The $(SUBDIRS) variable is only declared when U-Boot has been configured,
but it gets used all the time. In the non-configured case, it is used to
generate a helpful error message, but it needs to be set properly for that
to occur.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
Update CHANGELOG, fix minor coding stylke issue. Update Makefile.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
MECP5123 is a MPC5121E based module by esd gmbh.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
|
