| Age | Commit message (Collapse) | Author |
|---|
|
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
$(SRCTREE)/$(CPUDIR)/u-boot.lds is our default location
of arch-specific linker script.
Remove redundant definitions in
arch/{arc,microblaze,openrisc}/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
The syntax
CROSS_COMIPLE ?= <cross_compiler_prefix>
does not work because config.mk is parsed after
exporting CROSS_COMPILE.
Like Linux Kernel's arch/$(ARCH)/Makefile,
we must write as follows:
ifeq ($(CROSS_COMPILE),)
CROSS_COMPILE := <cross_compiler_prefix>
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
In case of little-endian ARC700 instructions (which may include target
address) are encoded as middle-endian. That's why it's required to swap
bytes after read and ten right before write back.
But in case of big-endian ARC700 instructions are encoded as a plain
big-endian. Thus no need for byte swapping.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Noam Camus <noamc@ezchip.com>
|
|
This file was only required for compilation of designware_i2c driver.
Since explicit inclusion of "hardware.h" is now removed from the driver
we may safely remove this empty header as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
|
|
These are library functions used by ARC700 architecture.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
These are header files used by ARC700 architecture.
Also note that "arch-arc700/hardware.h" is only required for compilation of
"designware_i2c" driver which refers to "asm/arch/hardware.h".
It would be good to fix mentioned driver sometime soon but it will cause
changes in ARM board configs that use "designware_i2c".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
