| Age | Commit message (Collapse) | Author |
|---|
|
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
The reference implementation of the PCI initialization code almost
everywhere contain this fragile loop of "a few usecs", and its
use of volatile variables to delay a number of bus cycles is indeed
uncertain.
Reading the manual "Integrator/AP Users Guide", page 5-15 it is
clearly stated:
"Wait until 230ms after the end of the reset period before
accessing V360EPC internal registers. The V360EPC supports the
use of a serial configuration PROM and the software must wait for
the device to detect the absence of this PROM before accessing any
registers. The required delay is a function of the PCI Clock, but
at the lower frequency (25MHz) is 230ms".
So let's simply wait 230ms per the spec.
This solves the compilation error that looked like this:
pci.c: In function ‘pci_init_board’:
pci.c:286:18: warning: variable ‘j’ set but not used
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PCI support for the Integrator AP has apparently never
been finished and I strongly suspect that it has never worked,
so let's fix it. This is a list of the more or less
un-splittable changes done in this driver rewrite:
- Replace the register definitions stashed into the config
file (!) with a copy if the register file from the Linux
kernels arch/arm/include/asm/hardware/pci_v3.h
- Delete the unreadable gigantic macros that perform the
config accesses and replace them with copyedited code from
Linux arch/arm/mach-integrator/pci_v3.c
- Rewrite the rest of the setup code to use the
v3_[read|write][lwb]() accessors.
- Enable PCI by default in the AP board configuration.
- Fix checkpatch warnings and make code more conformant.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The U-Boot startup infrastructure already makes sure pci_init() is
called at a proper time, calling it again from within the board
setup code will not make things better.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This enables Vpp and disables the flash protection on the
Integrator when starting U-Boot. The integrator/AP has double
protection mechanisms: this one and the EBI protection bit
(patch earlier), the Integrator/CP has only one line of
protection in these registers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Break out the AP system controller and CP "CP controller"
registers into a header file, it gives better overview than
hardcoding its values and other disturbing practices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reconfigures the EBI (External Bus Interface) on the
integrator so that chip select 1, handling the flash memory, is
set to writeable. Without this it is not possible for U-Boot to
access flash memory and it crashes on startup since CFI won't
work properly.
Since this is the first time we use the EBI, we create a header
file for its registers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Casting around to *(volatile ulong *) doesn't look good, so include
the <asm/io.h> macros and use good old readl() instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Do away with the config.mk file and move the text offset to the
config files to make things easier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When booting from Flash, the Integrator remaps its flash memory
from 0x24000000 to 0x00000000, and starts executing it at
0x00000000. This ROM thus hides the RAM underneath and first
0x40000 bytes of the memory cannot be tested by get_ram_size().
So let's test from 0x40000 to the end of detected memory
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The integrator board was apparently never converted over to support
relocation until now. After this the integrator u-boot both compiles
and boots on the Integrator AP.
This also fixes the SDRAM memory size detection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The integratorap/cp config for u-boot was outdated and would not
even compile, so fix the obvious missing bits for it to start
building. After this "make ap920t_config/make all" starts working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
|
|
|
|
|
|
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
|
|
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
|
|
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch fixes an error when running MAKEALL for ARM9.
On OS X /bin/sh uses builtin echo which does not utilise '-n' switch.
GNU manual for builtins recomend to use here-document style to solve
this portability issue.
This patch removes the usage of 'echo -n' and replace by here-document
style or a oneline echo command.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Peter Pearse <peter.pearse@arm.com>
|
|
pci_eth_init() is already conditional to CONFIG_PCI so not every caller
needs to have conditionals.
This is the only place in the current code base where such a check is
still at the calling site.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Peter Pearse <peter.pearse@arm.com>
|
|
According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.
This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().
Signed-off-by: Ingo van Lil <inguin@gmx.de>
|
|
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The board/armltd/integrator/split_by_variant.sh script used to print
"Configuring for integrator*p board..." no matter which board name
was being compiled. This made it difficult to match MAKEALL output to
board names. This patch fixes this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
|
