| Age | Commit message (Collapse) | Author |
|---|
|
Coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Correctly set PAD1_FREF_CLK4_REQ and PAD0_FREF_CLK4_OUT to enable and
activate both LEDs while setting pad mux.
Since this increases the line length, this patch also adjusts the white
space in this section of code to allign the pad mux signal description
comments.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
An upcoming version of Overo uses a Wifi/BT module with 1.8V signaling,
eliminating the need for an external transceiver to handle the level
shifting. This patch detects whether an external transceiver is present
and adjusts the pinmux settings as appropriate.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch adds support for the Beagle xM. It uses the board ID
GPIO bits to recognize this revision and perform appropriate setup.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Confiures GPMC timings for both chips and also configures pinmux
for GPIO_65, which is used as the interrupt signal for the second chip
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch enhances the revision detection function and adds
support for the C4 revision. The board revision is printed
and approriate revision specific setup is done automatically.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The latest Overo COM modules encode their revision number on
GPIOs 115, 113, and 112. All boards to date have no pullups on these pins
and hence appear as revision 0.
This patch reads and prints the revision information.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
This patch modifies the pinmux setup for MMC1_CLK and MMC3_CLK to enable
the input driver. MMC2_CLK was already properly configured.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
From the document, if set all arguments in "OUTPUT_FORMAT" to
"tradbigmips", then even add "-EL" to gcc we still get EB format.
pb1x00 is only used in Little-endian, so its default endian should be
set to LE.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
|
|
Use the MMU hardware to set up 1:1 mappings between physical and virtual
addresses. This allows us to bypass the cache when accessing the flash
without having to do any physical-to-virtual address mapping in the CFI
driver.
The virtual memory mappings are defined at compile time through a sorted
array of virtual memory range objects. When a TLB miss exception
happens, the exception handler does a binary search through the array
until it finds a matching entry and loads it into the TLB. The u-boot
image itself is covered by a fixed TLB entry which is never replaced.
This makes the 'saveenv' command work again on ATNGW100 and other boards
using the CFI driver, hopefully without breaking any rules.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
The paging system which is required to set up caching properties has not
yet been initialized when the SDRAM is initialized. So when the
map_physmem() function is converted to return the physical address
unchanged, the SDRAM initialization will break on some boards.
The avr32-specific uncached() macro will return an address which will
always cause uncached accessed to be made. Since this happens in the
board code, using avr32-specific features should be ok, and will allow
the SDRAM initialization to keep working.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Fix data size.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Update data address size and fix typo of register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Typically we declare the name of gpio structure to "gpio",
so it was duplicated around the name. (e.g: gpio->gpio_a)
This patch modified the naming that is removing "gpio_".
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
convert the board to the new soc architecture
update default config
i2c upgrade taken from eb_cpux9k2.h & board/BuS/eb_cpux9k2/cpux9k2.c
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
There was an redesign, so USB is available now.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
* convert meesc board to use c stucture SoC access
* change gpio access to at91_gpio syntax
* moved CONFIG_SYS_HZ below board and cpu defines (purely cosmetic)
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
We get two build errors:
fsl_elbc_nand.c: In function 'fsl_elbc_run_command':
fsl_elbc_nand.c:231: error: 'fsl_lbc_t' has no member named 'lsor'
make[1]: *** [/work/wd/tmp-ppc/drivers/mtd/nand/fsl_elbc_nand.o] Error 1
and
ve8313.c: In function 'initdram':
ve8313.c:104: error: expected '=', ',', ';', 'asm' or '__attribute__'
before '*' token
ve8313.c:104: error: 'lbc' undeclared (first use in this function)
ve8313.c:104: error: (Each undeclared identifier is reported only once
ve8313.c:104: error: for each function it appears in.)
ve8313.c:104: error: 'immap_t' has no member named 'lbus'
make[1]: *** [ve8313.o] Error 1
make: *** [board/ve8313/libve8313.a] Error 2
Due to changes to unifiy local bus struct definitions.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In function board_early_init_r(), serdes will not be initialize yet.
Thus sRIO was always considered disabled. Move the check for sRIO into
misc_init_r() which is called after fsl_serdes_init().
Also, fixed warning associated with gur variable possibly not being
used.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Lian Minghuan <B31939@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The board specific parameters associated with quad rank dimms where
missing. This fixes it so the board will function if quad rank dimms
are placed in it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
base address
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
|
|
In case there is no frame buffer driver present in Linux to hand over the
PPI LCD DMA upon boot, the DMA initiated by u-boot to display the splash
screen runs unattended. Therefore always stop the video driver in u-boot
before starting Linux. If people don't want this behavior, then they can
simply stub out the video_stop() function in their board video driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch adds support for the jadecpu board using the
MB86R01 'Jade' SoC from Fujitsu.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
|
|
|
|
|
|
|
|
|
|
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Update image size and default environment
after addition of new environment handling.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
