| Age | Commit message (Collapse) | Author |
|---|
|
mx6sabresd boards have a 18-bit LVDS data width and the correct color format
is RGB666.
Suggested-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging.
Configure them as active pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
This patch adds support for the AMPIRE 800x480 LCD panel that is available
for M53EVK.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Align with the context to use readl() to read the CCM_CCGR3
register with memory barrier instead of __raw_readl().
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add SATA support on uDoo Board.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
The pmic_init() function has the I2C or SPI bus number that is connected to the
PMIC.
Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x
definition.
The motivation for doing this is to avoid people just doing a copy and paste
of I2C_PMIC into their board file when another I2C bus is actually used to
interface to their PMIC.
This also makes more obvious which is the I2C bus connected to the PMIC, without
having to search in the source code for the meaning of the 'I2C_PMIC' number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds.
To disabled watchdog during kernel boot, WDI pin of that chip needs to be
in "high impedance" state. I.mx6 gpio configuration does not contemplate
tristate, so pin is set as input in high impedance.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031).
Ethernet speed is currently limited to 10/100Mbps.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.
Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.
Add support for it.
This patch allows the SPI NOR flash to be succesfully detected:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Currently HDMI splash screen is selected by default on mx6sabresd boards.
As LVDS is also enabled, this causes incorrect colors to be displayed im the
LVDS panel.
Fix this by selecting the LVDS panel as the default splash output and only keep
HDMI or LVDS turned on at the same time.
Acked-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
On efikamx board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
On mx31pdk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
On mx51evk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Since the titanium board is not a Freescale board, move its
BSP code from the freescale board directory to the newly created
barco board directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
|
|
When cpu_eth_init() fails we should not return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
When cpu_eth_init() fails we should not return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
If ipuv3_fb_init() fails, we should return the error immediately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
|
|
|
|
Convert sandbox to use common time functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Commit 1b0757e deleted the EP88x entry from boards.cfg file.
But it missed to remove include/configs/EP88x.h and board/ep88x/.
This commit removes them and adds EP88x to README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Klaus Heydeck <heydeck@kieback-peter.de>
|
|
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
|
|
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Convert vexpress to use the commmon timer code.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Wandboard quad was not ported into U-boot at the time of writing the README.
Add it to the list of Wandboard variants.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Current predefines do not fit cm-t3730 very well (some of them produce
artifacts in the image).
Update LCD predefines to accommodate both cm-t35 and cm-t3730 modules.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Compulab OMAP3 boards use the same display initialization code.
Move the display initialization code to live under board/compulab/common
directory.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Compulab boards use the same eeprom code, so move the eeprom related
code to live under board/compulab/common directory.
Also make several adjustments to eeprom functions namespace, so it will
be generic for compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
|
|
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
|
|
Also hang() the board on panic().
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
|
|
The new tricordereeprom command can read and write the eeprom for hardware
detection on tricorder devices.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
|
|
- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
|
