| Age | Commit message (Collapse) | Author |
|---|
|
When we have MMC available we assume that we want to put the env as a
file on FAT.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Change from EHCI to xHCI on the DFI BayTrail SoM.
The xHCI USB hub is connected to an GPIO on the DFI BayTrail SoM. For
correct operation, it needs to get reset upon power-up. Otherwise it
may happen that the hub is not detected after a software reboot. This
patch also configures this GPIO in the dts for correct operation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This config option is needed on the congatec x86 BayTrail board, as
otherwise the USB hub will not get initialized correctly. This
patch selects this Kconfig option again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Felipe Balbi <felipe.balbi@linux.intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert this PMIC driver to driver model and fix up other users. The
regulator and GPIO functions are now handled by separate drivers.
Update nyan-big to work correct. Three boards will need to be updated by
the maintainers: apalis-tk1, cei-tk1-som. Also the TODO in the code re
as3722_sd_set_voltage() needs to be completed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
A few lines (defines and declarations) had been duplicated when the
puma-rk3399 board was initially merged. This removes the duplicates
and changes the style to use local constants instead of pasted
literals.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[fixed up commit-message & converted to use 'const u32':]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Migrate all FMC defines from arch/arm/include/asm/arch-stm32f7/fmc.h
to drivers/ram/stm32_sdram.c
This will avoid to add an additionnal arch-stm32xx/fmc.h file when
a new stm32 family soc will be introduced.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
|
|
BeagleBoard X15 revC board is similar to X15 revB1 except
with a SR2.0 where revB1 uses a SR1.1. Add board detection
support for revC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
board_is*("rev", board_ti_get_rev()) uses strncmp() for
revison detection and assumes it is success if return value
is <= 0. This will fail in case of multiple versions, as
revb will be true for board_is_*revb() and board_is_*reva().
Fix it by looking for exact match of the string.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
It is possible to flag MAC addresses as locally administred. In this
case they don't need to be unique. This is only allowed for interfaces
which have no connection to the outside. For the TEGR1 board we use
this feature.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
|
|
If we rebrand the IVM and ethaddr was set previously we need to change
ethaddr. Otherwise we end up with a wrong MAC adress for the ethernet
interface.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
|
|
Disable RNG and add TEE to FDT used on HS devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Add support for loading a TEE and setting up firewalled regions to
AM43xx HS boards.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
I no longer have any of these boards, mark boards orphan.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
|
|
Since commit ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.
This is the equivalent fix from commit 4b6035da482c ("mx6sabresd: Make
Ethernet functional again").
Reported-by: Miquel RAYNAL <miquel.raynal@free-electrons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
By keeping WEIM disabled in U-Boot these kernel issues are gone.
Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
imx6qdl_icore_mmc_defconfig => imx6qdl_icore_rqs_defconfig
Since icorem6_rqs support MMC/eMMC boot, so doesn't need
to name it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
There is no need to add a 100us delay after the DDR initialization.
Other imx6 boards do not have such delay either, so simply remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The clearfog uses Armada 388.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.
This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
from the number of CSs
HWS_TIM_1T - enforce 1t
HWS_TIM_2T - enforce 2t
This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
|
|
|
|
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is not a very useful name since once it is probed it still hangs
around. With driver model we will use uclass data for this, so rename the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_SCSI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The instructions for creating a disk image that are presently in
README.sandbox fail because sfdisk doesn't know about GPT.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Enable all the boot-on regulator in default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Probe dwc2 udc in the function of board_usb_start to enable
usb gadget function.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
evb_rk3229 is a RK3229 based board, with:
- 8GB eMMC;
- 1GB DDR SDRAM;
- 2 USB2.0 HOST port;
- 1 MAC port;
- 1 HDMI port;
- IR;
- WiFi;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The bank0 ram size should be the DRAM size minus reserved size,
the DRAM size may be 1GB, 2GB, 4GB, we can not hard code it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added DECLARE_GLOBAL_DATA_PTR for RK3328, RK3368 and RK3399:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
|
