summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2013-10-16boards/c29xpcie: Update TLB and LAW size for IFC NAND, CPLDPrabhakar Kushwaha
NAND,CPLD AMASK register is programmed for 64K size. so Update TLB & LAW size accordingly. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-paShengzhou Liu
- Rename old P1010RDB board as P1010RDB-PA. - Add support for new P1010RDB-PB board. - Some optimization. For more details, see board/freescale/p1010rdb/README. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: fix conflicts in boards.cfg] Acked-by: York Sun <yorksun@freescale.com>
2013-10-16board/p1010rdb: add pin mux and sdhc support in any bootShengzhou Liu
Since pins multiplexing, SDHC shares signals with IFC, with this patch: To enable SDHC in case of NOR/NAND/SPI boot a) For temporary use case in runtime without reboot system run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC. b) For long-term use case set 'esdhc' in hwconfig and save it. To enable IFC in case of SD boot a) For temporary use case in runtime without reboot system run 'mux ifc' in u-boot to validate IFC with invalidating SDHC. b) For long-term use case set 'ifc' in hwconfig and save it. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-10-16powerpc/eeprom: update MAX_NUM_PORTS to adapt non-256-bytes EEPROMShengzhou Liu
Some boards use System EEPROM with 128-bytes instead of 256-bytes. Since we regard 256-bytes EEPROM as standard EEPROM with default value for MAX_NUM_PORTS. For those non-256-bytes EEPROM, we can redefine MAX_NUM_PORTS in board-specific file to override the default MAX_NUM_PORTS. This patch doesn't impact on previous existing boards. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-10-16powerpc/p1010rdb: remove unused cpld_showShengzhou Liu
Function cpld_show() was for debug and not called, so clean it. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-10-16powerpc/t1040qds: Add T1040QDS boardPrabhakar Kushwaha
T1040QDS is a high-performance computing evaluation, development and test platform supporting the T1040 QorIQ Power Architecture™ processor. T1040QDS board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: — PCI Express: supporting Gen 1 and Gen 2; — SGMII — QSGMII — SATA 2.0 — Aurora debug with dedicated connectors - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 8-bit, async, up to 2GB. - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - GASIC: Simple (minimal) target within Qixis FPGA - PromJET rapid memory download support - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - QIXIS System Logic FPGA - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - Video - DIU supports video at up to 1280x1024x32bpp - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V@1.5A per port. — Second port can be converted to OTG mini-AB - SDHC - SDHC port connects directly to an adapter card slot, featuring: - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC — Supporting eMMC memory devices - SPI - On-board support of 3 different devices and sizes - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: fix conflict in boards.cfg] Acked-by-by: York Sun <yorksun@freescale.com>
2013-10-16powerpc: Fix CamelCase warnings in DDR related codePriyanka Jain
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h has various parameters with embedded acronyms capitalized that trigger the CamelCase warning in checkpatch.pl Convert those variable names to smallcase naming convention and modify all files which are using these structures with modified structures. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
2013-10-16powerpc/B4860: enable PBL tool for B4860Shaohui Xie
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a pbl boot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2013-10-16powerpc/t4240: updated rcw_cfg to align with default hardware configurationShaohui Xie
Default configuration has been changed, the most important one is DDR ref_clock which is changed from 66.67MHz to 133.33MHz. so the ratio need to change from 24x to 12x to keep the DDR frequency. There are also some other optimise to align with default configuration. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2013-10-16powerpc: p1_p2_rdb_pc: add TPL for p1_p2_rdb_pc nand bootYing Zhang
Enable TPL for p1_p2_rdb_pc nand boot. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16powerpc : p1_p2_rdb_pc : Enable p1_p2_rdb_pc to start from eSPI with SPLYing Zhang
Enable p1_p2_rdb_pc to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16powerpc: p1_p2_rdb_pc: Enable p1_p2_rdb_pc to boot from SD Card with SPLYing Zhang
Enable p1_p2_rdb_pc to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-10-16SGMII:fix PHY addresses for QSGMII Riser Card working in SGMII modeZhao Qiang
Fix PHY addresses for QSGMII Riser Card working in SGMII mode on board P3041/P5020/P4080/P5040/B4860. QSGMII Riser Card can work in SGMII mode, but having the different PHY addresses. So the following steps should be done: 1. Confirm whether QSGMII Riser Card is used. 2. If yes, set the proper PHY address. Generally, the function is_qsgmii_riser_card() is for step 1, and set_sgmii_phy() for step 2. However, there are still some special situations, take P5040 and B4860 as examples, the PHY addresses need to be changed when serdes protocol is changed, so it is necessary to confirm the protocol before setting PHY addresses. Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-10-16Corenet/p5040/SGMII:fix the problem for SGMII5/6Zhao Qiang
SGMII5/6 and SGMII7/8 are not on the same slot on P5040 according to the serdes protocol. So it is not proper to organize SGMII5/6 and SGMII7/8 on one bus and SGMII5/6 can't work. So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for SGMII5/6 Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-10-16powerpc/c29xpcie: modify DDR parameter to make DDR more stablePo Liu
DDR parameters clk_adjust were changed. This can make the DDR run more stable. The new value were gotten by the DDR testing tool. Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-10-14Coding Style cleanup: drop some excessive empty linesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14Coding Style cleanup: remove trailing empty linesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14Coding Style cleanup: remove trailing white spaceWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14ARM: omap4-panda: Add MAC address creation for pandaDan Murphy
Add a MAC address create based on the OMAP die ID registers. Then poplulate the ethaddr enviroment variable so that the device tree alias can be updated prior to boot. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-14Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-10-11Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-10-09km/scripts: fix ramfsAndreas Huber
'actual_bank' is not used anymore, instead boot_bank is used. Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
2013-10-09powerpc/83xx: remove staticness for qe_iop_conf_tabHolger Brunck
commit a5510058 powerpc/83xx/km: make local functions and structs static removed the staticness also from this struct. But this struct is needed in arch/powerpc/cpu/mpc83xx/cpu_init.c and declared as extern. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-10-09Merge branch 'next' of git://git.denx.de/u-boot-mpc83xxTom Rini
2013-10-08Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-10-07socfpga: Adding pin mux handoff filesChin Liang See
Adding the generated pin mux configuration by Preloader Generator tool Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Acked-by: Dinh Nguyen <dinguyen@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-10-07socfpga: Adding System Manager driverChin Liang See
Adding System Manager driver which will configure the pin mux for real hardware Cyclone V development kit (not Virtual Platform) Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Acked-by: Dinh Nguyen <dinguyen@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-10-07omap1510inn: arm925t: remove supportAlbert ARIBAUD
omap1510inn is orphan and has been for years now. Reove it and, as it was the only arm925t target, also remove arm925t support. Update doc/README.scrapyard accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-10-07dra7xx_evm: add SPL API, QSPI, and serial flash supportMatt Porter
Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07pcm051/igep0033: Supply bd_ram_ofs for cpsw driverLars Poeschel
Since 2bf36ac638ab2db9f0295aa47064976eeebf80c1 the BD ram address is not hardcoded inside cpsw driver any more. Platforms have to supply their bd_ram_ofs in the platform data to the driver. This commit does this for pcm051 and igep0033 boards. Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-10-07ARM: IGEP0033: Update timing to run DDR at 400MHz.Enric Balletbo i Serra
We can run the DDR at 400MHz, so update the timings for that purpose. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-10-04Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-10-03ARM: VExpress: enable ARMv7 virt support for VExpress A15Andre Przywara
To enable hypervisors utilizing the ARMv7 virtualization extension on the Versatile Express board with the A15 core tile, we add the required configuration variable. Also we define the board specific smp_set_cpu_boot_addr() function to set the start address for secondary cores in the VExpress specific manner. There is no need to provide a custom smp_waitloop() function here. This also serves as an example for what to do when adding support for new boards. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-02Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-10-02Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-09-27mx35pdk: Fix error handling in board_late_init()Fabio Estevam
If smc911x_initialize() fails we should return the error immediately. While at it, also check the error from cpu_eth_init(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-27mx28evk: Propagate the error if cpu_eth_init() failsFabio Estevam
If cpu_eth_init() fails we should return the error immediately. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2013-09-27mx28evk: Propagate the error if cpu_eth_init() failsFabio Estevam
If cpu_eth_init() fails we should return the error immediately. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-25samsung: trats2: add support for new board Trats2Piotr Wilczek
This patch add support for a new Samsung board Trats2. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-09-25samsung:common:i2c: add definions for third soft I2C adapter for Trats2 boardPiotr Wilczek
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-09-24ARM: atmel: add RNDIS gadget supportBo Shen
Add RNDIS gadget support to test atmel usba udc driver Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-09-24DTS: Addition of I2S0 channel and replacing I2S1Dani Krishna Mohan
This patch enables default I2S0 channel.And I2S platform parameter has been moved to a common file viz exynos5.dtsi. Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
2013-09-20am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini
Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20mx28evk: Fix checkpatch warningFabio Estevam
Fix the following checkpatch warning: $ ./tools/checkpatch.pl -F board/freescale/mx28evk/mx28evk.c CHECK: Alignment should match open parenthesis #109: FILE: freescale/mx28evk/mx28evk.c:109: + writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN, + &clkctrl_regs->hw_clkctrl_enet); Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6slevk: Add Ethernet supportFabio Estevam
mx6slevk has a SMSC8720 connected in RMII mode. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6qsabreauto: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Reset counter to prevent error messageFabio Estevam
If a HDMI cable is not connected, the following message is seen on boot: CPU: Freescale i.MX6Q rev1.1 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 No panel detected: default to HDMI unsupported panel HDMI Reset the 'i' variable to fix the 'unsupported panel' message. This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skip). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>