summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2012-10-26mx25pdk: Add Ethernet supportFabio Estevam
mx25pdk has a Ethernet port that is connected to its internal FEC controller. In order to power up the Ethernet PHY (DP83640) it is necessary to communicate with the MC34704 PMIC via I2C. Make the FEC ethernet port functional Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26mx25: Place common functions into sys_proto.hFabio Estevam
imx-regs.h is meant to contain SoC register definitions. Common SoC funtions should go to sys_proto.h instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26mx25pdk: Add esdhc supportFabio Estevam
mx25pdk has a SD/MMC slot connected to esdhc1. Add support for it and allow the environment variables to be saved into SD/MMC. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26MX35: add support for woodburn boardStefano Babic
The woodburn board is based on the MX35 SOC. Support for both external (NOR) and internal (SD Card) boot mode are added. It uses the generic SPL framework to implement the internal boot mode. The following peripherals are supported: - Ethernet (FEC) - SD Card - NAND (512 MB) - NOR Flash In the internal boot mode, a simple imximage header is generated to set the address in internal RAM where the SOC must copy the SPL code. The initial setup is then demanded to the SPL itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26ARM: Fix start.S when used with SPL in arm1136Stefano Babic
This patch modifies start.S for the arm1136 to make it conform to start.S in armv7 architecture, to make it usable if the SPL framework is used. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-16i.MX6: mx6qsabrelite: Add splash screen supportEric Nelson
Adds support for HDMI, two LVDS panels and one RGB panel to the SABRE-Lite board. Displays supported: HDMI - 1024 x 768 for maximum compatibility Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1) wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600) wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480) Since the ipuv3_fb display driver currently supports only a single display, this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect or the I2C touch controller of the LVDS and RGB displays in the priority listed above. Setting 'panel' environment variable to one of the names above will override auto-detection. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: ipufb: add const to fb_videomode declarationsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: declare iomux_v3_cfg_t arrays as constEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16mx6qsabreauto: Pass the board revision to the kernelFabio Estevam
The kernel from Freescale expects that the bootloader passes the board revision. Read the board revision and pass it via get_board_rev(). Without passing the board revision the kernel does not operate properly as the initialization of peripherals are different in revA versus revB boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mxc: Fix SDHC multi-instance clockBenoît Thébaudeau
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not suitable for the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). This patch fixes this issue by adding a configuration field for the SDHC input clock frequency. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Andy Fleming <afleming@gmail.com>
2012-10-16mx35: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx35 lowlevel_init: - Indent with tabs. - Fix comments. - Use defined values instead of literal constants. - Use defined macros instead of duplicating code. - Use macro parameters with default values instead of #define'd configs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx6qsabreauto: Add Ethernet supportFabio Estevam
mx6qsabreauto has a AR8031 Gigabit PHY. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx25: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx25 lowlevel_init: - Add comments. - Do not use write32 repeatedly with the same value in order not to increase code size. - Make register values configurable. - Use macro parameters with default values instead of literal constants. - Use defined macros instead of duplicating code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Matthias Weisser <weisserm@arcor.de>
2012-10-15mx31: Fix PDR0_CSI_PODFBenoît Thébaudeau
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0 register is actually composed of two bit-fields: one pre-divider and one post-divider. This patch fixes the CCM access macros and the code using them accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6q: Add basic support for mx6qsabreautoFabio Estevam
mx6qsabreauto is a board based on mx6q SoC with the following features: - 2GB of DDR3 - 2 USB ports - 1 HDMI output port - SPI NOR - 2 LVDS LCD ports - Gigabit Ethernet - Camera - eMMC and SD card slot - Multichannel Audio - CAN - SATA - NAND - PCIE - Video Input Add very basic support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6qsabresd: Add 8-bit USDHC supportFabio Estevam
USDHC3 has 8 pins wired in mx6qsabresd. Configure the extra pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6qsabresd: Add Ethernet supportFabio Estevam
mx6qsabresd has a AR8031 Gigabit PHY. Add support for it. Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail. Tested on 1Gbp and 100Mbps networks. Suggested-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-15mx6: Add basic support for mx6qsabresd board.Fabio Estevam
mx6qsabresd is a board based on mx6q SoC with the following features: - 1GB of DDR3 - 1 USB OTG port - 1 HDMI output port - SPI NOR - LVDS panel - Gigabit Ethernet - Camera Connector - eMMC and SD card slot - Audio Add very basic support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6q: Factor out common DDR3 init codeFabio Estevam
Factor out common DDR3 initialization code, allowing easier maintainance of such scripts. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15tegra: nand: add board pinmuxLucas Stach
Boards may require a different pinmux setup for NAND than the default one. Add a way to call into board specific code to set this up. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: clean up board include hellLucas Stach
The prototypes used in board files were all scattered out, which lead to code duplication between SPL and normal U-Boot and some prototypes not actually being used. Consolidate this in a common board header. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra20: rework UART GPIO handlingLucas Stach
Rename board provided gpio_config_uart() to gpio_early_init_uart() as it does the same thing as the equally called function provided by the uart-switch code. This allows to simply call this function in early board init whether or not we are building with CONFIG_UART_SWITCH defined. Also provide a weak symbol for this function, to avoid the need to provide this function for boards that don't need any fixup. This patch supersedes the earlier posted "tegra: convert gpio_config_uart to weak symbol". Build tested with MAKEALL -s tegra20 Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15Tegra20: Move some include files to arch-tegra for sharing with Tegra30Tom Warren
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h. Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20' 'root' file. All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK. Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: Rename Medcom to Medcom-WideThierry Reding
Medcom is the marketing name for an older, PXA-based version of the same device. In order to avoid confusion, rename the Tegra-based version to the new marketing name. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15tegra: Update Avionic Design vendor prefixThierry Reding
The official vendor prefix for Avionic Design is now "ad". Update the board DTS files accordingly. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15usb: ehci: rework to take advantage of new lowlevel interfaceLucas Stach
Kill off ehci-core.h It was used to specify some static controller data. To support more than one controller being active at any time we have to carry the controller data ourselfes. Change the ehci interface accordingly. NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed to do the same thing as other platforms. But the change for now is at least compile clean. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15usb: lowlevel interface change to support multiple controllersLucas Stach
Carry an index in the lowlevel usb functions to make specify the respective usb controller. Also pass through an controller struct from lowlevel_init to the creation of the root usb device of this controller. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15pmc405de and zeus: remove the env_ptr externsIgor Grinberg
The env_ptr is already declared in environment.h, so there is no need to redeclare in board files (especially after including the environment.h) Remove those declarations. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-10-15ppc4xx: Remove AP1000 board supportStefan Roese
As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: James MacAulay <james.macaulay@amirix.com> Acked-by: Marek Vasut <marex@denx.de>
2012-10-15ppc4xx: Remove ML2 board supportStefan Roese
As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Marek Vasut <marex@denx.de>
2012-10-15serial: Remove CONFIG_SERIAL_MULTI from serial driversMarek Vasut
Remove the support for not-CONFIG_SERIAL_MULTI part from serial port drivers and some board files. Since CONFIG_SERIAL_MULTI is now enabled by default, that part is a dead code. Remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into p3mx serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into p3mx serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the p3mx driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into sconsole serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into sconsole serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the sconsole driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into ml2 serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into ml2 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the ml2 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into evb64260 serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into evb64260 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the evb64260 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into cpci750 serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into cpci750 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the cpci750 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into cogent serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into cogent serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the cogent driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into bmw serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into bmw serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the bmw driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into amirix serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into amirix serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the amirix driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: powerpc: Implement CONFIG_SERIAL_MULTI into marvell serial driverMarek Vasut
Implement support for CONFIG_SERIAL_MULTI into marvell serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the marvell driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2012-10-15serial: zoom2: Remove zoom2 serial prototypes from serial.hMarek Vasut
Remove the prototypes for zoom2_serial_deviceN from serial.h . This can't be done right away, as they are referenced from the zoom2 config file. Therefore, adjust the code so the config file only specifies number of the port. Then, replace the simple return in default_serial_console() with a switch across possible values, which returns the zoom2_serial_deviceN . With such adjustment in place, the exported prototypes in serial.h can be safely removed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
2012-10-15serial: pxa: Make use of default_serial_console in serial_pxaMarek Vasut
Make use of the newly implemented weak default_serial_console in the serial_pxa driver. This removes all reimplementations of this function from board files. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
2012-10-15serial: Properly spell out the structure member names of serial_driverMarek Vasut
Properly spell out the whole structure member names when an initialized varible is instantiated from the struct serial_driver. In case the structure definition for struct serial_driver undergoes reordering, there will be no impact on variables defined based on this structure. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: C Nauman <cnauman@diagraph.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Michal Simek <monstr@monstr.eu>
2012-10-15COMMON: Use __stringify() instead of rest of implementationsMarek Vasut
Fix up the rest of implementations of __stringify(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-10-15COMMON: Use __stringify() instead of MK_STR()Marek Vasut
Kill multiple occurances and redeclaration of MK_STR in favor of __stringify(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15gth2: Remove this platformTom Rini
After taking with the former maintainer, delete this platform. The patch is from the former maintainer. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15ARM: prevent misaligned array initsAlbert ARIBAUD
Under option -munaligned-access, gcc can perform local char or 16-bit array initializations using misaligned native accesses which will throw a data abort exception. Fix files where these array initializations were unneeded, and for files known to contain such initializations, enforce gcc option -mno-unaligned-access. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> [trini: Switch to usign call cc-option for -mno-unaligned-access as Albert had done previously as that's really correct] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-05MPC85xx: remove support for TQM85xx boardsWolfgang Denk
Due to grown code sizes the TQM85xx boards don't build any more with some older tool chains (like ELDK 4.2). As these boards have long reached EOL it seems a waste of effort trying to fix them. The vendor has agreed to drop support for them, too. So let's get rid of them. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> cc: Kim Phillips <kim.phillips@freescale.com> Acked-by: Stefan Roese <sr@denx.de>
2012-10-04sh: ap_sh4a_4a: Fixed initialization value of DDR memoryNobuhiro Iwamatsu
The wrong value was set as value of column of DDR memory for ap_sh4a_4a. 10 is the right value. This fixed this problem. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>