| Age | Commit message (Collapse) | Author |
|---|
|
A number of platforms had been using the distro default feature before
it was moved to Kconfig but did not enable the new Kconfig option when
it was enabled. This caused a regression in terms of features and this
introduces breakage when more things move to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_USB_KEYBOARD
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup MPC86* configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CONSOLE_SCROLL_LINES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_LCD
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.
However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.
This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.
That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
