| Age | Commit message (Collapse) | Author |
|---|
|
Add FEC support for Engicam i.CoreM6 RQS modules.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add FEC support for Engicam GEAM6UL module.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add I2C support for Engicam i.CoreM6 RQS modules.
icorem6qdl-rqs> i2c bus
Bus 0: i2c@021a0000
Bus 1: i2c@021a4000
Bus 2: i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
icorem6qdl-rqs> i2c bus
Bus 0: i2c@021a0000 (active 0)
4f: generic_4f, offset len 1, flags 0
Bus 1: i2c@021a4000
Bus 2: i2c@021a8000
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Rename defconfig files for better compatible with
respective board names and dts files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07)
Trying to boot from MMC1
U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530)
CPU: Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl-rqs>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1
U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl-rqs>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add NAND support for Engicam GEAM6UL board.
Boot Log:
--------
U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28)
Trying to boot from NAND
NAND : 256 MiB
U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100)
CPU: Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 42C
Reset cause: WDOG
Model: Engicam GEAM6UL
DRAM: 128 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
* Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add I2C support for Engicam GEAM6UL module.
geam6ul> i2c bus
Bus 0: i2c@021a0000
Bus 1: i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1
U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM: 128 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
geam6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add I2C support for Engicam i.CoreM6 qdl board.
icorem6qdl> i2c bus
Bus 0: i2c@021a0000
Bus 1: i2c@021a4000
Bus 2: i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
|
|
Add plugin support for mx6sllevk board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.
Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)
CPU: Freescale i.MX6SLL rev1.0 at 792MHz
CPU: Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM: 2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
|
|
UDOO Neo boards has one FEC port connected to KSZ8091, add support for it.
Tested on a UDOO Neo Full with "dhcp zImage" command.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
|
|
It's not necessary to define the processor in the defconfig file.
The preferred method to select the SoC is via Kconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
|
|
|
|
Enable hush parser in Armada-7040 and Armada-8040 DB default
configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable PCIe bus support in Armada-7040 DB default configuration
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable mvebu pin control support in the default configuration
files for Armada-7040 and Armada-8040 development boards
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable mvebu "bubt" command support in the default configuration
file for Armada-7040 and Armada-8040 development boards
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Do not overwrite the memory nodes in the kernel DT where some parts
of the memory region might be carved out.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Stop booting legacy uImage and now boot zImage.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Currently we let U-Boot find a spot at the end of DRAM at runtime, this
forces us to build an OPTEE image based on the size of DRAM for an EVM.
Add a default address that works across all current AM57xx EVMs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Currently we let U-Boot find a spot at the end of DRAM at runtime, this
forces us to build an OPTEE image based on the size of DRAM for an EVM.
Add a default address that works across all current DRA7xx EVMs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable Linear Physical Address Extension mode which is a
prerequisite for hypervisor mode.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing
changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
|
|
|
|
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use embded option because of qemu
Use my repo till Stephen merge it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Series-to: sjg, agraf@suse.de
Series-cc: uboot
Series-version: 4
Series-changes: 2
- make ceva_init_sata static
- Move SATA_CEVA to defconfig
- Initalized max_lun and max_id platdata
Series-changes: 3
- Extend Kconfig help description
- sort dm.h
- Remove SPL undefinition from board file
- Fix Kconfig dependecies
|
|
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
|
|
|
|
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
This patch adds PCI support to the Marvell Armada-8K devel board.
Additionally the Intel E1000 ethernet driver is enabled so that
network support is available on this board, even without the
internal network interfaces being supported (yet).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
|
|
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
|
Commit 4c4e3b37750f3("ARM: AM43xx: Enable FIT") accidentally disabled
DM_SPI and DM_SPI_FLASH. Add back DM_SPI and DM_SPI_FLASH to
am43xx_evm_defconfig in order to make use of DM framework for QSPI.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
|
|
Add initial DTS support for AM571-IDK evm.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
DRA71-evm uses LP873x regulator. Enable lp873x PMIC config options.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
