summaryrefslogtreecommitdiff
path: root/drivers/ddr
AgeCommit message (Collapse)Author
2016-01-25drivers/ddr/fsl: fsl_ddr_sdram_size remove unused controllersEd Swarthout
Following commit 61bd2f75, exclude unused DDR controller from calculating RAM size for SPL boot. Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25driver/ddr/fsl: Add workaround for A009663Shengzhou Liu
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0 before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE] to the desired value after DDR initialization has completed. When DDR controller is configured to operate in auto-precharge mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25fsl/ddr: Add workaround for ERRATUM_A009942Shengzhou Liu
During the receive data training, the DDRC may complete on a non-optimal setting that could lead to data corruption or initialization failure. Workaround: before setting MEM_EN, set DEBUG_29 register with specific value for different data rates. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-19Add more SPDX-License-Identifier tagsTom Rini
In a number of places we had wordings of the GPL (or LGPL in a few cases) license text that were split in such a way that it wasn't caught previously. Convert all of these to the correct SPDX-License-Identifier tag. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-16ddr: altera: Init the rule ID in debug codeMarek Vasut
Init the rule ID, otherwise the debug code will always dump the protection settings entry 0. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Dinh Nguyen <dinh.linux@gmail.com>
2016-01-14mvebu: axp: Rename MV_DDR_32BIT to CONFIG_DDR_32BITPhil Sutter
This should make it clear that this symbol is meant to be defined by board headers. Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14axp: Fix debugging support in DDR3 write levelingPhil Sutter
If MV_DEBUG_WL is defined, DEBUG_WL_S and DEBUG_WL_D macros are missing. In addition to that, get rid of debug output printing non-existent counter variable. Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14arm: mvebu: Make ECC support configurable on Armada XPStefan Roese
Currently, ECC support is enabled for all Armada XP boards. So the DDR3 driver tries to configure the controller with ECC support, even on boards without ECC. This patch makes this ECC optional which now can be configured on a board-per-board basis. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Phil Sutter <phil@nwl.cc>
2016-01-14arm: mvebu: ddr: Fix compilation warningStefan Roese
gcc 5.1 generates this new warning (for Armada 38x platforms): drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result': drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument] memcpy(result, training_result, sizeof(result)); ^ drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM]) ^ Since this functions is not referenced anywhere, lets just remove it. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-12-15move erratum a008336 and a008514 to soc specific fileYao Yuan
As the errata A008336 and A008514 do not apply to all LS series SoCs (such as LS1021A, LS1043A) we move them to an soc specific file Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-14fsl/ddr: updated ddr errata-A008378 for arm and power SoCsShengzhou Liu
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0, T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on LS102x Rev2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-14driver/ddr/fsl: Update timing config for heavy loadYork Sun
In case four chip-selects are all active, the turnaround times need to increase to avoid overlapping under heavy load. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-14driver/ddr/fsl: Update workaround for A008511 for vref rangeYork Sun
The workaround requires different setting for range 1 vs 2. Also adjust timeout value for waiting for controller to be idle. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-14driver/ddr/fsl: Update MR5 RTT parkYork Sun
For four chip-selects enabled case, RTT is parked on all of them. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-14driver/ddr/fsl: Update DDR4 MR6 for Vref rangeYork Sun
MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-14driver/ddr/fsl: Update DDR4 RTT valuesYork Sun
DDR4 has different RTT value and code according to JEDEC spec. Update the macros and options . Signed-off-by: York Sun <yorksun@freescale.com>
2015-11-30drivers/ddr/fsl: Fix typo in BIST test for DDR4York Sun
BIST test code has a typo, resulting the binding registers not maintained as expected. This typo results BIST runs twice on the covered memory. Signed-off-by: York Sun <yorksun@freescale.com> Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2015-11-30drivers/ddr/fsl: Enable detection of one DDR controller operation for LSCH3York Sun
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of reset. It can be configured to disable one controller. To support this operation, the driver needs to detect and skip the disabled controller. Signed-off-by: York Sun <yorksun@freescale.com>
2015-11-30armv8: ls2085a: Add support of LS2085A SoCPrabhakar Kushwaha
Freescale's LS2085A is a another personality of LS2080A SoC with support of AIOP and DP-DDR. This Patch adds support of LS2085A Personality. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: Updated MAINTAINERS files Dropped #ifdef in cpu.h Add CONFIG_SYS_NS16550=y in defconfig] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8: LS2080A: Rename LS2085A to reflect LS2080APrabhakar Kushwaha
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc. So renaming existing LS2085A code base to reflect LS2080A (Prime personality) Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: Dropped #ifdef in cpu.c for cpu_type_list] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-17arm: mvebu: Fix SAR1_CPU_CORE_MASKDirk Eibach
SAR1_CPU_CORE_MASK was wrong, probably copy/paste from another architecture. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
2015-11-17arm: mvebu: a38x: Remove unsupported topologiesKevin Smith
A lot of extra configuration information was left over in the Marvell serdes and DDR3 initialization code for boards that U-boot does not support. Remove this extra config information, and the concept of fixing up board topologies with information loaded from an EEPROM. If this needs to be done, it should be handled in the board file, not in core code. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-11-10Various Makefiles: Add SPDX-License-Identifier tagsTom Rini
After consulting with some of the SPDX team, the conclusion is that Makefiles are worth adding SPDX-License-Identifier tags too, and most of ours have one. This adds tags to ones that lack them and converts a few that had full (or in one case, very partial) license blobs into the equivalent tag. Cc: Kate Stewart <kstewart@linuxfoundation.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-30drivers/ddr/fsl_ddr: Make SR_IE configurableJoakim Tjernlund
SR_IE(Self-refresh interrupt enable) is needed for Hardware Based Self-Refresh. Make it configurable and let board code handle the rest. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-11bitops: introduce BIT() definitionHeiko Schocher
introduce BIT() definition, used in at91_udc gadget driver. Signed-off-by: Heiko Schocher <hs@denx.de> [remove all other occurrences of BIT(x) definition] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2015-08-23ddr: altera: Repair uninited variableMarek Vasut
Fix the following problem: drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full': drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized] if (found_passing_read && found_failing_read) ^ drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here u32 found_passing_read, found_failing_read, initial_failing_dtap; ^ Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-23ddr: altera: Replace float multiplication with integer oneMarek Vasut
This gem is really really rare, there was an actual float used in the Altera DDR init code, which pulled in floating point ops from the libgcc, just wow. Since we don't support floating point operations the same way Linux does not support them, replace this with an integer multiplication and division combo. This removes some 2kiB of size from the SPL as the floating point ops are no longer pulled in from libgcc. This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which does not contain the floating point bits. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-17arm: mvebu: Add complete SDRAM ECC scrubbingStefan Roese
This patch introduces the SDRAM scrubbing for ECC enabled board to fill/initialize the ECC bytes. This is done via the XOR engine to speed up the process. The scrubbing is a 2-stage process: 1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot 2) U-Boot scrubs the remaining SDRAM area(s) Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-08-17arm: mvebu: sdram: Enable ECC support on Armada XPStefan Roese
This is tested on the DB-MV784MP-GP eval board. To really enable ECC support on this board the I2C EEPROM needs to get changed. As it saves the enabling of ECC support internally. For this the following commands can be used to enable ECC support on this board: Its recommended for first save (print) the value(s) in this EEPROM address: => i2c md 4e 0.1 2 0000: 05 00 .. To enable ECC support you need to set bit 1 in the 2nd byte: Marvell>> i2c mw 4e 1.1 02 Marvell>> i2c md 4e 0.1 2 0000: 05 02 .. To disable ECC support again, please use this command: Marvell>> i2c mw 4e 1.1 00 Marvell>> i2c md 4e 0.1 2 0000: 05 00 .. On other AXP boards, simply plugging an ECC DIMM should be enough to enable ECC support. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-08-08ddr: altera: sequencer: Clean checkpatch issuesMarek Vasut
Fix most of the dangling checkpatch issues, no functional change. There are still 7 warnings, 1 checks , but those are left in place for the sake of readability of the code. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Clean data typesMarek Vasut
Replace uintNN_t with uNN. No functional change. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Pluck out misc macros from codeMarek Vasut
Actually convert the sequencer code to use socfpga_sdram_misc_config instead of the various macros. This is just an sed exercise here, no manual coding needed. This patch actually removes the need to include any board-specific files in sequencer.c , so sequencer.c namespace is now no longer poluted by QTS-generated macros. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Zap SEQ_T(INIT|RESET)_CNTR._VALMarek Vasut
This is another macro used to obfuscate the real code. The T(INIT|RESET)_CNTR._VAL is always defined, so this indirection is unnecessary. Get rid of this. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Zap VFIFO_SIZEMarek Vasut
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Wrap misc remaining macrosMarek Vasut
Introduce structure socfpga_sdram_misc_config to wrap the remaining misc configuration values in board file. Again, introduce a function, socfpga_get_sdram_misc_config(), which returns this the structure. This is almost the final step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Pluck out IO_* macros from codeMarek Vasut
Actually convert the sequencer code to use socfpga_sdram_io_config instead of the IO_* macros. This is just an sed excercise here, no manual coding needed. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Wrap IO_* macrosMarek Vasut
Introduce structure socfpga_sdram_io_config to wrap the IO configuration values in board file. Introduce socfpga_get_sdram_io_config() function, which returns this the structure. This is another step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Pluck out RW_MGR_* macros from codeMarek Vasut
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config instead of the RW_MGR_* macros. This is just an sed exercise here, no manual coding needed. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Wrap RW_MGR_* macrosMarek Vasut
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager configuration values in board file. Introduce a complementary function, socfpga_get_sdram_rwmgr_config(), which returns this the structure. This is another step toward wrapping the nasty QTS generated macros in board files and reducing the pollution of the namespace. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Wrap ac_rom_init and inst_rom_initMarek Vasut
Introduce two wrapper functions, socfpga_get_seq_ac_init() and socfpga_get_seq_inst_init() to avoid direct inclusion of the sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS generated files. This reduces namespace pollution again. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Zap bogus redefinition of RW_MGR_MEM_NUMBER_OF_RANKSMarek Vasut
This is defined in the QTS-generated headers, so it must not be re-defined in sequencer.h . Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Zap unused params and macrosMarek Vasut
These parameters are not used in the code, zap them and the macros which are used by them as well. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sequencer: Move qts-generated files to board dirMarek Vasut
Move the files generated by QTS into the board directory, they should not be part of the driver files at all. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
2015-08-08ddr: altera: sdram: Make sdram_start and sdram_end into u32Marek Vasut
Originally, both sdram_start and sdram_end were 64b values. The sdram_start had no reason for being so, since our address space is only 32b, so switching sdram_start to u32 is simple. The sdram_end is a bit more complex, since it can actually be set to (1 << 32) if someone really wanted to use an SoCFPGA with 4 GiB of DRAM and fixed the code around a little. But, the code handling the protection rules internally decrements the sdram_end variable anyway. Thus, instead of calling the code and passing in the address of the SDRAM end, pass in the address already decremented by one. This lets the sdram_end be 32b as well. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Minor cleanup in sdram_get_rule()Marek Vasut
Fix the data types and zap unnecessary type change. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Minor cleanup in sdram_set_rule()Marek Vasut
Zap an obscure unneeded cast and clean other minor nits in this function. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Add missing kerneldocMarek Vasut
Add kerneldoc to functions which are missing it, but are already cleaned up. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Clean up sdram_write_verify()Marek Vasut
Clean the function up so that it's obvious what it is doing, fix the formating strings in debug outputs, add kerneldoc. Make the function return proper errno-compliant return values and propagate this change throughout sdram.c Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Clean up sdram_calculate_size() part 2Marek Vasut
Clean up coding style, mostly clean up comments, add kerneldoc. Also, zap assignment of the "cs" variable, which is outright dead code, so just remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2015-08-08ddr: altera: sdram: Clean up sdram_calculate_size() part 1Marek Vasut
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change makes sdram.c completely clear of these macros and allows removing of the ugly include of sdram.h . The namespace is now a much nicer place! Signed-off-by: Marek Vasut <marex@denx.de>