| Age | Commit message (Collapse) | Author |
|---|
|
In a system where the initial u-boot location is genuinely NOR flash (as
opposed to RAM or a cache-line setup by a pre-bootloader) writes to the
data section are problematic. At best these writes have no effect, at
worst they put the flash memory into a status mode which changes the
executable code underneath us.
Pass around a stack variable from the top of the twsi i2c driver to
avoid writing to global data.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
|
|
The DW I2C controller in the SPEAr SoCs doesn't support the enable
status register check. This patch selects
SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED for these boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
This patch adds an entry for the Designware I2C driver in Kconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Some platforms don't implement the enable status register at offset 0x9c.
The SPEAr600 platform is one of them. The recently added check to this
status register can't be performend on these platforms.
This patch introduces a new config option that can be enabled on such
platforms not supporting this register.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add support for common TI i2c mux which is available on ZynqMP zcu102
board.
DM i2c mux core code is selecting/deselecting bus before/after
every command is performed that's why only one channel is active at a
time. That's also the reason why deselect is just disable all available
channels.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
400kHz is maximum freq which can be used on Xilinx ZynqMP.
Support it with standard divider calculator.
Input freq is hardcoded to 100MHz input freq till we have clock driver
which can provide this information for exact configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
set_bus_speed is the right function where bus speed should be setup.
This move enable option to remove probe and remove functions which are
empty.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Extract reading IP base address in function which is designed for it.
Also enable option to read more information from DT in this function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This patch adds DM support to the designware I2C driver. It currently
supports DM and the legacy I2C support. The legacy support should be
removed, once all platforms using it have DM enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
This patch prepares the designware I2C driver for the DM conversion.
This is mainly done by removing struct i2c_adapter from the functions
that shall be used by the DM driver version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
Integrating set_speed() into dw_i2c_set_bus_speed() will make the
conversion to DM easier for this driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
dw_i2c_enable() is used to dis-/en-able the I2C controller. It makes
sense to add such a function, as the controller is dis-/en-abled
multiple times in the code. Additionally, this function now checks,
if the controller is really dis-/en-abled. This code is copied
from the Linux I2C driver version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add the ic_enable_status register to the i2c_regs struct. Additionally
the register offsets are added, to better check, if the offset matches
the register description in the datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
This is a possible drop in replacement for drivers/i2c/zynq-i2c.c
Since this is cadence IP it has been renamed to cdns-i2c,
to make sense with the compatible string.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Guy Thouret <guy.thouret@wems.co.uk>
Cc: Heiko Schocher <hs@denx.de>
|
|
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
|
|
newer sunxi SoCs"
"Fix mvtwsi not working on sun6i and newer sunxi SoCs" includes the following:
@@ -189,7 +200,8 @@ static int twsi_start(struct i2c_adapter *adap, int expected_status)
/* globally set TWSIEN in case it was not */
twsi_control_flags |= MVTWSI_CONTROL_TWSIEN;
/* assert START */
- writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control);
+ twsi_control_flags |= MVTWSI_CONTROL_START | MVTWSI_CONTROL_CLEAR_IFLG;
+ writel(twsi_control_flags, &twsi->control);
/* wait for controller to process START */
return twsi_wait(adap, expected_status);
}
The modification of twsi_control_flags done here was introduced while
merging to fix a line > 80 chars, but twsi_control_flags is a global variable
and should not be modified like this here, this commit fixes this, restoring
mvtwsi functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Move the init code into the I2C driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is used on most Intel platforms. We don't have a driver for it yet, but
add a stub to handle the init. For now this targets ivybridge so we may want
to add a device tree binding and generalise it when other platforms are
supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Since I2C muxes are seldom needed in SPL, and the code for this increases
the size somewhat, add a separate option to enable I2C muxes for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We can use the new clk_get_by_index() function to get the correct clock.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
On sun6i and newer IFLG is a write-clear bit which is cleared by writing 1,
rather then a normal r/w bit which is cleared by writing 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 3 checkpatch warnings
in drivers/i2c/mvtwsi.c:
WARNING: line over 80 characters
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
|
|
This could avoid executing the code that only applies to i.MX platforms.
The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.
Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Use tabs instead of space for indentation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Fix typo in command description.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
compiling U-Boot for avr32 boards shows since
commit 3d1957f0ea01 "dm: i2c: Add support for multiplexed I2C buses"
this warning:
Building current source for 4 boards (4 threads, 8 jobs per thread)
avr32: + atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
0 4 0 /4 0:00:16 : atngw100mkii
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Since busses are sorted in alphabetical order, introducing more
than nine busses led to unexpected behaviour.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
hrcon DH(dual head) has two video outputs per FPGA.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
|
|
Bus has to be held for repeated start regardless of
read/write access.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Reinhard Pfau complained that macros in ihs_i2c do not follow best practices.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Support two i2c masters per FPGA.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
