summaryrefslogtreecommitdiff
path: root/drivers/mtd/spi
AgeCommit message (Collapse)Author
2016-07-29sf: sf_params: Add AT25DF321 flash supportWenyou Yang
Add AT25DF321 flash support. Fix AT25DF321A device name. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-29spi: Add support for N25Q016AMoritz Fischer
This commit adds support in the spi-nor driver for the N25Q016A, a 16Mbit SPI NOR flash from Micron. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-15sunxi: Support booting from SPI flashSiarhei Siamashka
Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-03driver: mtd: spi: Adding support for QSPI flashPrabhakar Kushwaha
Serial number, vendor id and page size are added for QSPI flash common on both LS1012AQDS and LS1012ARDB i.e. S25FS512SDSMFI011. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-27spl: Support loading a FIT from SPILokesh Vutla
Detect a FIT when loading from SPI and handle it using the new FIT SPL support. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-05-18sf: Disable 4-KB erase command for SPANSION S25FS-S familyYuan Yao
The S25FS-S family physical sectors may be configured as a hybrid combination of eight 4-kB parameter sectors at the top or bottom of the address space with all but one of the remaining sectors being uniform size. The default status of the flash is in this hybrid architecture. The parameter sectors and the uniform sectors have different erase commands. This patch disable the hybrid sector architecture then the flash will has uniform sector size and uniform erase command. This configuration is temporary, the flash will revert to hybrid architecture after power on reset. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18spi: fsl_qspi: Enable Spansion S25FS-S family flashesYuan Yao
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write any device register command and read any device register command. This patch enable support for those commands. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17SPL: Let spl_parse_image_header() return valueMarek Vasut
Allow the spl_parse_image_header() to return value. This is convenient for controlling the SPL boot flow if the loaded image is corrupted. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
2016-04-25sf: fix timebase data type in _wait_ready()Stephen Warren
get_timer() returns an unsigned 64-bit value, but is currently assigned to a signed 32-bit variable. Due to sign extension and data truncation, this causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and incorrectly) fire for about 50% of all time values, based on whether bit 31 is set. In sandbox at least, this causes the test to pass or fail based on system uptime, as opposed to time since the U-Boot binary was started. Fixes: 4efad20a1751 ("sf: Update status reg check in spi_flash_cmd_wait_ready") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-03-12sf: Correct data types in stm_is_locked_sr()Marek Vasut
The stm_is_locked_sr() function is picked from Linux kernel. For reason unknown, the 64bit data types used by the function and present in Linux were replaced with 32bit unsigned ones, which causes trouble. The testcase performed was done using ST M25P80 chip. The command used was: => sf protect unlock 0 0x10000 The call chain starts in stm_unlock(), which calls stm_is_locked_sr() with negative ofs argument. This works fine in Linux, where the "ofs" is loff_t, which is signed long long, while this fails in U-Boot, where "ofs" is u32 (unsigned int). Because of this signedness problem, the expression past the return statement to be incorrectly evaluated to 1, which in turn propagates back to stm_unlock() and results in -EINVAL. The correction is very simple, just use the correctly sized data types with correct signedness in the function to make it work as intended. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-26spi: Correct two error return valuesSimon Glass
When an error number is provided we should use it, not change it. This fixes the SPI and SPI flash tests. One of these is long-standing. The other seems to have been introduced by commit 1e90d9fd (sf: Move read_id code to sf_ops). Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 1e90d9fd (sf: Move read_id code to sf_ops) Reviewed-by: Jagan Teki <jteki@openedev.com> Tested-by: Jagan Teki <jteki@openedev.com>
2016-02-26sandbox: spi: Remove an incorrect free()Simon Glass
We must not free data that is managed by driver mode. Remove this line, which is a hangover from the pre-driver-model code. This fixes a problem where 'sf probe' crashes U-Boot if the backing file for the SPI flash cannot be found. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-26sandbox: spi: Add more debugging to SPI emulationSimon Glass
Add a little more debugging to help when things go wrong. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com> Tested-by: Jagan Teki <jteki@openedev.com>
2016-02-23sf: spi_flash: use dma to copy data from mmap region if platform supportsMugunthan V N
Add dma memcpy api to the default spi_flash_copy_mmap(), so that dma will be used to copy data when CONFIG_DMA is defined for the platform. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-22spi: Correct device tree usage in spi_flash_decode_fdt()Simon Glass
This function currently searches the entire device tree for a node that it thinks is relevant. But the node is known and is passed in. Correct the code and enable it only with driver model, since only driver-model boards will use it. This avoids bringing in a large number of strings from fdtdec. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-15dm: spi_flash: Allow the uclass to work without printf()Simon Glass
For SPL we don't really need sprintf() and with tiny-printf this is not available. Allow this to be dropped in SPL when using tiny-printf. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-13sf: Make IO modes at last in read modesJagan Teki
SLOW, FAST, DUAL, DUAL_IO, QUAD, QUAD_IO changed order to SLOW, FAST, DUAL, QUAD, DUAL_IO, QUAD_IO Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename op_mode_rx to mode_rxJagan Teki
Since spi rx mode macro's are renamed to simple and meaninfull, this patch will rename the respective structure members. Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Write quad bit along with read statusJagan Teki
While setting quad bit on spansion, macronix code is writing only particular quad bit this may give wrong functionality with other register bits, So this patch fix the issue where it with write previous read reg status along particular quad bit. Cc: Vignesh R <vigneshr@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once macronix quad bit setJagan Teki
One macronix quad bit set using SR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once spansion quad bit setJagan Teki
One spansion quad bit set using CR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Fix quad bit set for micron devicesJagan Teki
Setting up quad bit for micron devices need to do the same way as other flash devices like spansion, winbond etc does using enhanced volatile config register so this patch adds this support instead of printing "QEB is volatile" Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Peter Pan <peterpandong@micron.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Use BIT macroJagan Teki
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Minor cleanupJagan Teki
- Tab space - Place all read commands at one place. - Re-arrange write commands. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Remove spi_flash_removeJagan Teki
Use direct call to device_remove instead of exctra spi_flash_remove defination. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename bank_end to bar_end in read_barJagan Teki
bar_end gives more meaningfull compared to bank_end and spi_flash_write_bar uses bar_end so replaced bank_end with bar_end in spi_flash_read_bar Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename spi_flash_set_* functionsJagan Teki
Since quad_mode functions are local to spi flash core, rename them to a meaningful and readable names. Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Move spi_read_cmds_array locallyJagan Teki
Since spi_read_cmds_array is used locally in spi_flash_scan, so move array to locally used function instead of defining global array. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename SPI_TX_BP|QPP to SPI_TX_BYTE|QUADJagan Teki
Since SPI_TX_* are spi_slave{} members so use spi protocol notation instead spi flash programming, like SPI_TX_BP => SPI_TX_BYTE SPI_TX_QPP => SPI_TX_QUAD Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Use mode instead of op_mode_txJagan Teki
Used mode member from spi_slave{} instead of op_mode_tx. Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Get spi locally from spi_flashJagan Teki
For better code readabilty, get the spi pointer from spi_flash{} locally and use it instead of direct dereferring spi pinter as flash->spi->* Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-07spi: spi_flash: Fix the arguments of stm_is_locked_sr()Fabio Estevam
stm_is_locked_sr() takes the status register (SR) value as the last parameter, not the second. Based on a patch from Brian Norris for the linux kernel: http://git.infradead.org/linux-mtd.git/commit/a32d5b726ff8cf32bf491522b0ac8ae2545a063e Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Rename sf_ops.c to spi-flash.cJagan Teki
Since all spi-flash core operations are moved into sf_ops.c then it's better to renamed as spi-flash.c Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Use static for file-scope functionsJagan Teki
Used static for file-scope functions in sf_probe.c Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: sf_probe: Remove spi_slave pointer argumentJagan Teki
Since spi_slave is a spi pointer in spi_flash{} then assign spi_slave{} pointer to flash->spi and remove spi_slave pointer argument to - spi_flash_probe_slave - spi_flash_scan Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: ops: Fix missing break on spansion read_barJagan Teki
For assigning read_bar commands in spansion case, break is missing this patch add that break. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Remove unneeded SST_BP and SST_WPJagan Teki
SST parts added on sf_params.c supports both SST_WR which consits of both BP and WP and there is a spi controller ich which supports only BP so the relevent _write hook set based on "slave->op_mode_tx" hence there is no respective change required from flash side hance removed these. Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Remove unneeded header includesJagan Teki
Removed unneeded header includes in sf_ops and sf_probe Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Flash power up read-only based on idcode0Jagan Teki
Using macro's for flash power up read-only access code leads wrong behaviour hence use idcode0 for runtime detection, hence the flash which require this functionality gets detected at runtime. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Use simple name for register access functionsJagan Teki
Most of the register access function are static, so used simple name to represent each. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Fix MakefileJagan Teki
This patch removes unneeded ifdef and fixed accordingly. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Use static for file-scope functionsJagan Teki
Use static for file-scope functions and removed them from header files. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: probe: Code cleanupJagan Teki
- Move bar read code below the bar write hance both at once place, hence it easy for #ifdef macro only once and readable. - Move read_cmd_array at top Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Move read_id code to sf_opsJagan Teki
read_id code is related to spi_flash stuff hence moved to sf_ops. Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: Move spi_flash_scan code to sf_opsJagan Teki
Intension is that sf_ops should deals all spi_flash related stuff and sf_probe (which should renamed future) should be an interface layer for spi_flash versus spi drivers. sf_ops => spi_flash interface sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11sf: spi_flash_validate_params => spi_flash_scanJagan Teki
Rename spi_flash_validate_params to spi_flash_scan as this code not only deals with params setup but also configure all spi_flash attributes. And also moved all flash related code into spi_flash_scan for future functionality addition. Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-11-19Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2015-11-19dm: sf: Add support for all targets which requires MANUAL_RELOCMichal Simek
It is follow up patch based on "dm: Add support for all targets which requires MANUAL_RELOC" (sha1: 484fdf5ba058b07be5ca82763aa2b72063540ef3) to update function pointers for DM. Using post_bind is not ideal but it is one on current option what can be used. Variable reloc_done has to be used do not call relocation after every bind. Maybe new core functions should be introduced for this case. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-18spl: change return values of spl_*_load_image()Nikita Kiryanov
Make spl_*_load_image() functions return a value instead of hanging if a problem is encountered. This enables main spl code to make the decision whether to hang or not, thus preparing it to support alternative boot devices. Some boot devices (namely nand and spi) do not hang on error. Instead, they return normally and SPL proceeds to boot the contents of the load address. This is considered a bug and is rectified by hanging on error for these devices as well. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Hans De Goede <hdegoede@redhat.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Jagan Teki <jteki@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit v0.10.2 at 2024-08-01 04:50:00 (GMT)