summaryrefslogtreecommitdiff
path: root/drivers/net/vsc9953.c
AgeCommit message (Collapse)Author
2016-04-06drivers: net: vsc9953: Fix bug when PVID is shown for disabled ports onlyCodrin Ciubotariu
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06drivers: net: vsc9953: Do not configure disabled portsCodrin Ciubotariu
Some SerDes protocols might not enable all l2switch ports. In this case, these ports should not be configured to perform Rx/Tx operations. This also fixes an issue when flooded frames were also switched to disabled ports and frames start to accumulate, consuming memory and eventually causing head-of-line blocking for other frames. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-28drivers: net: vsc9953: Add LAG supportCodrin Ciubotariu
You can now configure LAG on VSC9953's ports using the command: ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>} A port must belong to a single LAG. By default, a port belongs to a LAG equal to the port's number. For each frame, a hash will be calculated based on Source/Destination MAC addresses, Source/Destination IP(v4/v6) addresses, Source/Destination ports. This hash will be used to select a single egress port from LAG. This also assures that frames from the same flow will always have the same egress port. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28drivers: net: vsc9953: Fix FDB aging timeCodrin Ciubotariu
By default, the aging period is set to 0, so the dynamic FDB entries are never removed. This patch sets the aging time to 300 seconds. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-09-21drivers/net/vsc9953: Add GPL-2.0+ SPDX-License-IdentifierCodrin Ciubotariu
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add commands for VLAN ingress filteringCodrin Ciubotariu
The command: ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port can be used to enable/disable/show VLAN ingress filtering on a port. This command has also been added to the ethsw generic parser from common/cmd_ethsw.c Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add command for shared/private VLAN learningCodrin Ciubotariu
The command: ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private" configures the FDB to share the FDB entries learned on multiple VLANs or to keep them separated. By default, the FBD uses private VLAN learning. This command has also been added to the ethsw generic parser from common/cmd_ethsw.c Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add VLAN commands for VSC9953Codrin Ciubotariu
The new added commands can be used to configure VLANs for a port on both ingress and egress. The new commands are: ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port; ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members); ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mod for a port" ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - Configure VID source for egress tag. Tag's VID could be the frame's classified VID or the PVID of the port These commands have also been added to the ethsw generic parser from common/cmd_ethsw.c Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add commands to manipulate the FDB for VSC9953Codrin Ciubotariu
The new command: ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } Can be used to add and delete FDB entries. Also, the command can be used to show entries from the FDB tables. When used with [port <port_no>] and [vlan <vid>], only the matching the FDB entries can be seen or flushed. The command has also been added to the generic ethsw parser from cmd_ethsw.c. Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add commands to enable/disable HW learningCodrin Ciubotariu
The command: ethsw [port <port_no>] learning { [help] | show | auto | disable } can be used to enable/disable HW learning on a port. This patch also adds this command to the generic ethsw parser from cmd_ethsw. Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add command to show/clear port countersCodrin Ciubotariu
The new added command: ethsw [port <port_no>] statistics { [help] | [clear] } will print counters like the number of Rx/Tx frames, number of Rx/Tx bytes, number of Rx/Tx unicast frames, etc. This patch also adds this commnd in the genereric ethsw parser from cmd_ethsw.c Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Use the generic Ethernet Switch parserCodrin Ciubotariu
This patch replaces the parser used by VSC9953 L2 Switch driver with the generic one. Also, the config macro that enables the VSC9953 commands has been replaced in all the platforms that use this driver with the config macro that corresponds to the generic parser. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Add default configuration for VSC9953 L2 SwitchCodrin Ciubotariu
At startup, the default configuration should be: - enable HW learning on all ports (HW default); - all ports are VLAN aware; - all ports are members of VLAN 1; - all ports have Port-based VLAN 1; - on all ports, the switch is allowed to remove maximum one VLAN tag, - on egress, the switch should add a VLAN tag if the frame is classified to a different VLAN than the port's Port-based VLAN; Signed-off-by: Johnson Leung <johnson.leung@freescale.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Fix bug when enabling a portCodrin Ciubotariu
When a port is enabled at init time, the initializing function touches more bits than necessary to enable a port (also touches reserved bits and default bit values). This patch fixes this issue by changing the value of the define used to enable the port and assures that no other bits are changes by replacing out_le32() with setbits_le32(). Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Cleanup patchCodrin Ciubotariu
This patch groups some macros defined for registers and replaces some magic numbers from vsc9953 with macros. Also, "port" and "port_nr" words are replaced with "port_no", puts each variable declaration on a line and removes unnecessary tabs. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21drivers/net/vsc9953: Remove 'CONFIG_' from macros' nameCodrin Ciubotariu
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-23net/memac_phy: reuse driver for little endian SoCsShaohui Xie
The memac for PHY management on little endian SoCs is similar on big endian SoCs, so we modify the driver by using I/O accessor function to handle the endianness, so the driver can be reused on little endian SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access is little endian, if not, the I/O access is big endian. Move fsl_memac.h out of powerpc include. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2015-01-16net/vsc9953: Add driver for Vitesse VSC9953 L2 Switch IPCodrin Ciubotariu
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP is integrated in Freescale T1040 and T1020 SoCs. The L2 switch has 10 Ethernet ports: 2 internal fixed-links (ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps. The external ports may be connected to PHYs over QSGMII and SGMII. Commands have also been added to enable/disable a port and to check a port's link speed, duplexity and status. The commands are: ethsw port <port_nr> enable|disable - enable/disable an l2 switch port ethsw port <port_nr> show - show an l2 switch port's configuration port_nr=0..9; use "all" for all ports For more detailse please see doc/README.t1040-l2switch Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>