| Age | Commit message (Collapse) | Author |
|---|
|
The gpio api has been tested on an armadeus apf27.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
gpio_get_value() should use PSR like Linux, not DR, because DR does not always
reflect the pin state, while PSR does. This is especially useful to detect a
short circuit on a GPIO pin configured as output, or to read the level of a pin
controlled by a non-GPIO IOMUX function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Use calloc() instead of malloc() to allocate the mxs_spi_slave structure.
Clearing the memory is necessary since most of the time this gets done
super early in boot, but on warm reboots, and when SPI probing is done
long after the init stages it could actually pick up previously used memory,
and things like the chipselect polarity and other data end up being filled
with trash data if not explicitly set by the board files.
This solves a semi-random, almost unreproducable error whereby SPI devices
act very, very strangly on boot.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Use calloc() instead of malloc() to allocate the mxc_spi_slave structure.
Clearing the memory is necessary since most of the time this gets done
super early in boot, but on warm reboots, and when SPI probing is done
long after the init stages it could actually pick up previously used memory,
and things like the chipselect polarity and other data end up being filled
with trash data if not explicitly set by the board files.
This solves a semi-random, almost unreproducable error whereby SPI devices
act very, very strangly on boot. Tested on Efika MX over several years..
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Since the input frequency of the API is a maximum that should not be exceeded in
order for the devices to operate properly, the SPI clock divider should be
rounded up, not truncated.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
This driver has been tested on board armadeus apf27.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
The CLKCTRL registers are SoC specific so we ought to have it clear on
filename.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
This patch support exynos pwm backlight driver. It can control backlight
power and brightness by using pwm.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
If dp_enabled was set, exynos fb driver support display port feature.
This patch depends on [PATCH] video: support exynos fimd driver
for various exynos series.
http://marc.info/?l=u-boot&m=134119605104467&w=2
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch set supports exynos display port drivers.
DisplayPort is an industry standard device to accommodate the increasing board
adoption of digital display technology within the PC and consumer electronics.
The interface supports internal chip-to-chip and external box-to-box digital
display connections.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch supports exynos fimd driver for various exynos series different from
existing it supports only exynos4 chip.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This SoC is used in the Raspberry Pi, for example.
For more details, see:
http://www.broadcom.com/products/BCM2835
http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf.
Initial support is enough to boot to a serial console, execute a minimal
set of U-Boot commands, download data over a serial port, and boot a
Linux kernel. No storage or network drivers are implemented.
GPIO driver originally by Vikram Narayanan <vikram186@gmail.com>
with many fixes from myself.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
Configuration in vexpress and u8500.v1 is different from what
is needed in u8500.v2. As such, card configuration specifics need
to reside in the board file rather than the driver.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/gpio/Makefile
|
|
Orjan Friberg wrote at [1]:
"For the beagleboard, ecc.size is not explicitly set when doing 'nandecc
sw'. If it's not set for the NAND_ECC_SOFT case in nand_scan_tail, it's
set to 256 bytes.
When doing 'nandecc hw', ecc.size is set to 512 bytes. Hence, when
changing back to 'nandecc sw' ecc.size remains at 512 bytes and suddenly
the format has changed."
No patch has been submitted and the issue was still present. This patch
adds the mentioned solution. Tested on a tam3517 board.
[1] http://lists.denx.de/pipermail/u-boot/2012-February/119002.html
cc: Orjan Friberg <of@flatfrog.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
|
|
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add support for Freescale's i.MX DryIce RTC, present on i.MX25.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
The DMA didn't work properly because the DMA descriptor wasn't
properly cleaned after it was used once. Also, the DMA_ENABLE bit
was enabled/disabled too late.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
|
|
Large blocks (> 512b) shall be transfered via DMA to make
things a bit faster.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
|
|
Move DMA and PIO data transfer parts into separate functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
|
|
The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
Also, it was using SSP0 DMA channel for all SSP devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
The DMA transfers happen only if the transfered data are larger
than 512 bytes. Otherwise PIO is used. This is a small speed
optimization.
The DMA transfer doesn't work if unaligned transfer is requested
due to the limitation of the DMA controller. This has to be fixed
by introducing generic bounce buffer. Therefore the DMA feature
is now disabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Pull out all the PIO transfer logic into separate function,
so DMA can be added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
This makes it easier to adapt for addition of DMA support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
|
|
also fix NS16550_init() as we need 16x divider
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
|
|
Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.
Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.
CC: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
|
|
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
* 'sf' of git://git.denx.de/u-boot-blackfin:
sf: spansion: Add support for S25FL256S
sf: winbond: fix page_size
sf: stmicro: add support for N25Q128A
sf: stmicro: add support N25Q128 parts
sf: stmicro: support JEDEC standard two-byte signature
sf: winbond: add W25Q32
cmd_spi: remove superfluous semicolon
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Add support for Spansion S25FL256S SPI flash.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size
from 256 to 4096. This prevents either/both of "sf write" writing the
correct data, or "sf read" from reading the correct data back.
This allows U-Boot running on Compulab Tegra to upgrade itself.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips
fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Support for DS1388 is added by extending the DS1337 driver. DS1388 is
similar to DS1337. The time registers are offset by 1 (due to support
for hundreds of seconds), and there is no century bit.
The configuration and trickle charge registers are also different.
Tested on hardware with Freescale P2010 and DS1388.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
|
|
Add support for Numonyx N25Q128A SPI flash.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Adds support for Numonyx's N25Q128 SPI flash. These devices
are used on (among others) Avnet Spartan-6 LX9 micro-evaluation
boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There are more than the M25Pxx serial flashs that can be
used with the stmicro driver, for example: the M25PXxx or
N25Qxx serie. All these chips have burned in the original
stmicro manufacture id 0x20 together with a standard
two-byte signature.
In preperation to support all these chips the stmicro driver
have to decode the full two-byte signature.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
SMDK EVT1 has a different Winbond part, added its part details
to the SPI flash table.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Renesas SH and R-Mobile set up device using PFC.
This provide the framework. Most codes were brought from linux kernel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The serial device of R8A7740 has the same structure as SH7372 of SH, etc.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The serial device of SH73A0 has the same structure as SH7372 of SH, etc.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
