| Age | Commit message (Collapse) | Author |
|---|
|
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
the former
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
|
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
With this patch u-boot can fixup the dr_mode and phy_type properties
for the Dual-Role USB controller.
While at it, also remove #ifdefs around includes, they are not needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Though NAND chip is replaceable on the MPC837XE-MDS boards, the
current settings don't work with the default chip on the board.
Nevertheless Freescale's U-Boot sets the option register correctly,
so I just dumped the register from the working u-boot. My guess is
that the old settings were applicable for some pilot boards, not
found in the production.
This patch also enables FSL ELBC driver so that we could access
the NAND storage in the u-boot.
The NAND support costs about 45KB, so the u-boot no longer fits
into two 128KB NOR flash sectors, thus we also have to adjust
environment location: add another 128KB to the monitor length.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
It is due to hardware design and logic defect, that is the
I/O[0:7] of NAND chip is connected to LAD[7:0], so when
the NAND chip connected to nLCS3, you have to set up the
OR3[BCTLD] = '1' for normal operation, otherwise it will have
bus contention due to the pin 48/25 of U60 is enabled.
Setup the OR3[BCTLD] = '1' , that meaning the LBCTL is not
asserted upon access to the NAND chip, keep the default state.
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:
- When the CPLD recognizes its location on the PIB it automatically
configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
configured as an Agent and the PCI is configured to an external arbiter.
This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).
In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This involves configuring the SerDes and fixing up the flags and
PHY addresses for the TSECs.
For Linux we also fix up the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
move the BRx_* and ORx_* left behind in mpc85xx.h
The same is needed for mpc8xx.h and mpc8260.h (defines are almost
the same, just few differences which needs some attention though).
But the bad news for mpc8xx and mpc8260 is that there are a lot of users
of these defines. So this cleanup I'll leave for the "better times".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now. Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
|
|
Currently the SATA controller clock is configured as CSB clock,
usually the CSB clock is 400/333/266MHz.
However, The SATA IP block is only guaranteed to operate up to
200 MHz as stated in the HW spec.
The bug is reported by Joe D'Abbraccio <ljd015@freescale.com>
This patch makes the SATA clock as half of CSB clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Enable the first two SATA interfaces on MPC837xEMDS board,
The two SATA ports are on LYNX1. (SATA0/1 on J4/5)
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.
Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
1. Make the CSB bus pipeline depth as 4, and enable
the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Remove the "#undef DEBUG" line from all Freescale 83xx board header files.
The inclusion of this line makes it impossible to enable debug code in
other source files, because "#define DEBUG" typically needs to be defined
before any header files are included.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Format the code, make it more readable
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Reduce the AL from 2 to 1 clock to improve the performance.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
clean up the cache config from configs.h of board
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
continuation of commit 37395fa2b0d9d617f28d44ca11592260ef16105a to 837x
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x.
This change guarantees that the environment will be located on the
first flash sector after the U-Boot image.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
