| Age | Commit message (Collapse) | Author |
|---|
|
enable generic board support for the ipam390 board.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a67e
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM926EJS and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.
Remove the redundant definition in config headers.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.
In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.
CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
warning: "CONFIG_SPL" redefined [enabled by default]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
|
|
Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
|
|
add the am1808 based ipam390 board from Barix.
- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM
interface
- 128MByte, NAND Flash, 8bit databus to the NANDFlash
Interface
- Ethernet PHY Micrel KSZ8051R via RMII
- Console on UART 0
- booting fron nand flash
- spl falcon bootmode
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
|
