| Age | Commit message (Collapse) | Author |
|---|
|
User's confirmation is asked in different commands. This commit adds a
function for such confirmation.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
|
|
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
|
|
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
|
|
Since B&R boards uses only MMC-Controller #1, it only
wastes time if we initialize #0 first to see that there is nothing.
Cc: <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
|
|
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.
The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has
been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS,
P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ying Zhang <b40530@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Haijun.Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Shaohui Xie <Shaohui.Xie@freescale.com>
|
|
baord_init_f takes one argument, boot_flag. It has not been used for
powerpc, until recently changing to use generic board architecture.
The boot flag is added as a return value from cpu_init_f().
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
|
|
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.
Also update board maintainer for these boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
This patch enables the E500 QEMU board to use the generic cross-arch board
infrastructure.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Enable errata A006261, A006593, A006379 for T208x.
Additionally enable CONFIG_CMD_ERRATA for T2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
|
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
|
|
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
|
|
|
|
|
|
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
In fat_write.c, the last clust condition check is incorrect:
if ((curclust >= 0xffffff8) || (curclust >= 0xfff8)) {
... ...
}
For example, in FAT32 if curclust is 0x11000. It is a valid clust.
But on above condition check, it will be think as a last clust.
So the correct last clust check should be:
in fat32, curclust >= 0xffffff8
in fat16, curclust >= 0xfff8
in fat12, curclust >= 0xff8
This patch correct the last clust check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
This bug shows up when file stored on the ext4 file system is updated.
The ext4fs_delete_file() is responsible for deleting file's (e.g. uImage)
data.
However some global data (especially ext4fs_indir2_block), which is used
during file deletion are left unchanged.
The ext4fs_indir2_block pointer stores reference to old ext4 double
indirect allocated blocks. When it is unchanged, after file deletion,
ext4fs_write_file() uses the same pointer (since it is already initialized
- i.e. not NULL) to return number of blocks to write. This trunks larger
file when previous one was smaller.
Lets consider following scenario:
1. Flash target with ext4 formatted boot.img (which has uImage [*] on itself)
2. Developer wants to upload their custom uImage [**]
- When new uImage [**] is smaller than the [*] - everything works
correctly - we are able to store the whole smaller file with corrupted
ext4fs_indir2_block pointer
- When new uImage [**] is larger than the [*] - theCRC is corrupted,
since truncation on data stored at eMMC was done.
3. When uImage CRC error appears, then reboot and LTHOR/DFU reflashing causes
proper setting of ext4fs_indir2_block() and after that uImage[**]
is successfully stored (correct uImage [*] metadata is stored at an
eMMC on the first flashing).
Due to above the bug was very difficult to reproduce.
This patch sets default values for all ext4fs_indir* pointers/variables.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Some new boards define CONFIG_SYS_HZ again! Remove.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
|
|
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.
In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
|
|
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.
For ex.
is_zero_ether_addr()
is_multicast_ether_addr()
is_broadcast_ether_addr()
is_valid_ether_addr();
So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.
Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
|
|
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
|
|
|
|
Some machines do not have SDL libraries installed, and it is still useful
to build sandbox without LCD/keyboard support.
Add an option for this, used as follows:
make sandbox_config all NO_SDL=1
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Conflicts:
drivers/net/Makefile
(trivial merge)
|
|
|
|
- expand the condition with CONFIG_OF_CONTROL
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
When both CONFIG_API and CONFIG_LCD are enabled, the API code calls
lcd_display_bitmap(). That isn't compiled unless either CONFIG_CMD_BMP
or CONFIG_SPLASH_SCREEN is enabled. In order to prevent build problems,
have config_fallbacks.h enable CONFIG_CMD_BMP when both API and LCD are
enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Last argument shouldn't be there.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
|
|
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Future patches will make DFU too large to fit in this board's SPL build.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
|
When user attempted to perform a raw write using DFU (vide
dfu_fill_entity_mmc) with MMC interface not initialized before,
get_mmc_blk_size() reported invalid (zero) block size - it wasn't
possible to write ie. a new u-boot image.
This commit fixes that by initializing MMC device before use in
dfu_fill_entity_mmc().
While fixing initialization sequence, I had to change about half of
dfu_fill_entity_mmc's body, so I refactored it on the way to make it,
IMHO, considerably more comprehensible.
Being left as dead code, get_mmc_blk_size() was removed.
Tested on Samsung Goni.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
