| Age | Commit message (Collapse) | Author |
|---|
|
Convert the SH Serial to Kconfig using tools/moveconfig.py tool
and a bit of manual adjustment to cater for failed conversions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Allow pasting extra long lines into the U-Boot console on RCar Gen3.
This is OK since we have plenty of resources and it's convenient.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add initial support for the R8A7795 and R8A7796 based ULCB board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
After MMC is converted to DM, convert to use DM SCSI as well for all
x86 boards and imply BLK for both MMC and SCSI drivers.
CONFIG_SCSI_DEV_LIST is no longer used. Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This converts Intel ICH6 GPIO driver to Kconfig, and add it to the
imply list of platform drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Some LDOs have a bypass capability. Make sure that the bypass is disabled
when is the LDO is enabled (otherwise the voltage can't be changed).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
At present if U-Boot proper uses driver model for MMC, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
Add new SPL versions of the options for DM_MMC, DM_MMC_OPS and BLK. By
default these follow their non-SPL versions, but this can be changed by
boards which need it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present the AHCI SCSI driver only supports PCI with driver model.
Rename the existing function to indicate this and add support for adding
a non-PCI controller .
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
With driver model the serial device is often not called "serial". Mark
driver-model stdio devices so that they can be detected and we can look up
the uclass. This is a more reliable way of finding out whether the console
is connected to a serial device or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_TWL4030_PWM is not being used by any source, so let's remove the #define
and the whitelist entry
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add CONFIG_STM32X7_SERIAL as a Kconfig option.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Patch queue for efi - 2017-07-29
A lot of EFI greatness this time around. Thanks a lot to the
two amazing new contributors
Heinrich Schuchardt and
Rob Clark
we now gain
- stable objects across multiple bootefi invocations
- fixes for shim
- fixes for ipxe
- protocol installation
- device path conversion to/from text
- working "lsefi" support in grub
- working notifiers
- various bug fixes
|
|
There is no SMSC LPC47M Super I/O chipset on the MinnowMax board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Felipe Balbi <felipe.balbi@linux.intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
|
|
This should make it easier to see when a callback back to UEFI world
calls back in to the u-boot world, and generally match up EFI_ENTRY()
and EFI_EXIT() calls.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: remove static from const var]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Missing an EFI_ENTRY() or doubling up EFI_EXIT() leads to non-obvious
crashes. Let's add some error checking.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: fix bogus assert() and fix app_gd breakage]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Move clk_release_all() prototype and definition inside
OF_CONTROL flag to avoid following compilation error for
poplar platform:
aarch64: + poplar
+drivers/usb/host/built-in.o: In function `ehci_usb_remove':
+drivers/usb/host/ehci-generic.c:159: undefined reference to `clk_release_all'
+drivers/usb/host/built-in.o: In function `ehci_usb_probe':
+drivers/usb/host/ehci-generic.c:133: undefined reference to `clk_release_all'
+make[1]: *** [u-boot] Error 139
+make: *** [sub-make] Error 2
Introduced by 4e542c4 clk: add clk_release_all()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
To avoid compilation breakage on platform that doesn't
support DM PHY but uses xhci-dwc3 driver, add the missing
CONFIG_PHY flag.
Introduced by patch :
84e53877 "usb: host: xhci-dwc3: Add generic PHY support"
Cc: Ran Wang <ran.wang_1@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Ran Wang <ran.wang_1@nxp.com>
|
|
Change long (32 bits on arm) to u64 (same type than offset)
for size and read offset r_left
So partition and device used for DFU can be greater than 4GB
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
solve issue on get_medium_size() function
the detection of error is a simple test < 0
but for ARM platform, long is 32bits and 2GB = 0x80000000
is seen as error.
I solve the issue by changing the prototype fo the function
to separate size and result.
This patch prepare the next patch with size change to u64.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
For USB host controllers like xHC, its internal representation of
hub needs to be updated after the hub descriptor is fetched. This
adds a new op that does this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A high speed hub has a special responsibility to handle full speed/
low speed devices connected on downstream ports. In this case, the
hub must isolate the high speed signaling environment from the full
speed/low speed signaling environment with the help of Transaction
Translator (TT). TT details are provided by hub descriptors and we
parse and save it to hub uclass_priv for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
USB 3.0 hub uses a hub depth value multiplied by four as an offset
into the 'route string' to locate the bits it uses to determine the
downstream port number. We shall set the hub depth value of a USB
3.0 hub after it is configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Sometimes we need know if a given hub device is root hub or not.
Add a new API to test this. This removes the xHCI driver's own
version is_root_hub() and change to use the new API.
While we are here, remove the unused/commented out get_usb_device()
in the xHCI driver too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present hub_port_reset() is defined in DM USB, but it is never
called hence remove it (removing another ifdefs).
While we are here, change legacy_hub_port_reset() name to
usb_hub_port_reset() to better match other function names in the
same hub module.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Occasionally it was observed that on Intel MinnowMax board, with a
USB 2.0 device connected to the bottom port, when doing 'usb start'
on the xHCI controller:
scanning bus 0 for devices... cannot reset port 3!?
But neither of the two USB ports is routed to xHCI root port 3.
Adding some debug information shows that xHCI port 3 PORTSC register
mysteriously reports both CCS = 1 and CSC = 1.
This is not seen every time. After increasing the timeout to wait
for power to become stable, the issue is gone. So this indicates
current default USB power-on delay (20ms) might be at a critical
region where power is stable/unstable. U-Boot provides a mechanism
to have a environment variable to override the default one. Add
one for MinnowMax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
USB 3.0 hub port status has different bit position regarding to
port power, port speed, etc. But others are the same as 2.0 hubs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0
hubs, with a fixed (rather than variable length) size. Change the
host controller drivers that access those last two fields
(DeviceRemovable and PortPowerCtrlMask) to use the union.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel
MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI
reports a transfer event TRB with a completion code 6 which means
'Stall Error'.
In fact super speed USB hub descriptor type is 0x2a, not 0x29.
Sending correct SETUP packet to the hub makes it not stall anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
This function is usefull to get phandle number contained
in a property list.
For example, this allows to allocate the right amount
of memory to keep clock's reference contained into the
"clocks" property.
To implement it, either of_count_phandle_with_args() or
fdtdec_parse_phandle_with_args() are used respectively
for live tree and flat tree.
By passing index = -1, these 2 functions returns the
number of phandle contained into the property list.
Add also the dev_count_phandle_with_args() based on
ofnode_count_phandle_with_args()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add clk_release_all() method which Disable/Free an
array of clocks that has been previously requested by
clk_request/get_by_*()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add reset_release_all() method which Assert/Free an
array of resets signal that has been previously successfully
requested by reset_get_by_*()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is needed in error path to assert previously deasserted
reset by using a saved reset_ctl reference.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This allow to check if a PHY has been correctly
initialised and avoid to get access to phy struct.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
These are not needed now since the drivers now use driver model. Drop
them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
Convert this PMIC driver to driver model and fix up other users. The
regulator and GPIO functions are now handled by separate drivers.
Update nyan-big to work correct. Three boards will need to be updated by
the maintainers: apalis-tk1, cei-tk1-som. Also the TODO in the code re
as3722_sd_set_voltage() needs to be completed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
This pmic includes GPIOs which should have their own driver. Add
a driver to support these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
This pmic includes regulators which should have their own driver. Add
a driver to support these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
We sometimes need to read a resource from an arbitrary node. In any case
for consistency we should not put the live-tree switching code in
a dev_read_...() function. Update this to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
They are unused since commit d8c6fb8cedbc ("sandbox: Drop special
case console code for sandbox").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
DT property values can be strings as well as integers. This is why
of_get_property/fdt_getprop returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
