summaryrefslogtreecommitdiff
path: root/lib
AgeCommit message (Collapse)Author
2016-05-28Merge git://git.denx.de/u-boot-dmTom Rini
For odroid-c2 (arch-meson) for now disable designware eth as meson now needs to do some harder GPIO work. Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: lib/efi_loader/efi_disk.c Modified: configs/odroid-c2_defconfig
2016-05-27efi_loader: gop: Don't expose fb addressAlexander Graf
Recently Linux is gaining support for efifb on AArch64 and that support actually tries to make use of the frame buffer address we expose to it via gop. While this wouldn't be bad in theory, in practice it means a few bad things 1) We expose 16bit frame buffers as 32bit today 2) Linux can't deal with overlapping non-PCI regions between efifb and a different frame buffer driver For now, let's just disable exposure of the frame buffer address. Most OSs that get booted will have a native driver for the GPU anyway. Signed-off-by: Alexander Graf <agraf@suse.de> [trini: Remove line_len entirely] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27efi_loader: Clean up system table on exitAlexander Graf
We put the system table into our runtime services data section so that payloads may still access it after exit_boot_services. However, most fields in it are quite useless once we're in that state, so let's just patch them out. With this patch we don't get spurious warnings when running EFI binaries anymore. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-05-27efi_loader: Add bounce buffer supportAlexander Graf
Some hardware that is supported by U-Boot can not handle DMA above 32bits. For these systems, we need to come up with a way to expose the disk interface in a safe way. This patch implements EFI specific bounce buffers. For non-EFI cases, this apparently was no issue so far, since we can just define our environment variables conveniently. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-05-27dm: efi: Update for CONFIG_BLKSimon Glass
This code does not currently build with driver model enabled for block devices. Update it to correct this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexander Graf <agraf@suse.de>
2016-05-27efi_loader: Add network access supportAlexander Graf
We can now successfully boot EFI applications from disk, but users may want to also run them from a PXE setup. This patch implements rudimentary network support, allowing a payload to send and receive network packets. With this patch, I was able to successfully run grub2 with network access inside of QEMU's -M xlnx-ep108. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-05-27tiny-printf: Support snprintf()Simon Glass
Add a simple version of this function for SPL. It does not check the buffer size as this would add to the code size. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2016-05-27tiny-printf: Tidy up a few nitsSimon Glass
- Rename 'w' to 'width' to make it more obvious what it is used for - Use bool and int types instead of char to avoid register-masking on 32-bit machines Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2016-05-17dm: part: Drop the block_drvr tableSimon Glass
This is not needed since we can use the functions provided by the legacy block device support. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-02Change my mailaddressAndreas Bießmann
I'll switch my mails to my own server, so drop all gmail references. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-04-18efi_loader: Handle memory overflowsAndreas Färber
jetson-tk1 has 2 GB of RAM at 0x80000000, causing gd->ram_top to be zero. Handle this by either avoiding ram_top or by using the same type as ram_top to reverse the overflow effect. Cc: Alexander Graf <agraf@suse.de> Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Alexander Graf <agraf@suse.de>
2016-04-18gunzip.c: use block layer for writesEric Nelson
Call blk_dwrite to ensure that the block cache is notified if enabled and remove build breakage when CONFIG_BLK is enabled. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
2016-04-18efi_loader: Expose ascending efi memory mapAlexander Graf
The EFI memory map does not need to be in a strict order, but 32bit grub2 does expect it to be ascending. If it's not, it may try to allocate memory inside the U-Boot data memory region. We already sort the memory map in descending order, so let's just reverse it when we pass it to a payload. Signed-off-by: Alexander Graf <agraf@suse.de> Tested-by: Andreas Färber <afaerber@suse.de>
2016-04-18efi_loader: Always flush in cache line size granularityAlexander Graf
The cache line flush helpers only work properly when they get aligned start and end addresses. Round our flush range to cache line size. It's safe because we're guaranteed to flush within a single page which has the same cache attributes. Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: Andreas Färber <afaerber@suse.de>
2016-04-18efi_loader: Increase path string to 32 charactersAlexander Graf
Whenever we want to tell our payload about a path, we limit ourselves to a reasonable amount of characters. So far we only passed in device names - exceeding 16 chars was unlikely there. However by now we also pass real file path information, so let's increase the limit to 32 characters. That way common paths like "boot/efi/bootaa64.efi" fit just fine. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-04-18efi_loader: Add el torito supportAlexander Graf
When loading an el torito image, uEFI exposes said image as a raw block device to the payload. Let's do the same by creating new block devices with added offsets for the respective el torito partitions. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-04-18efi_loader: Split drive add into functionAlexander Graf
The snippet of code to add a drive to our drive list needs to get called from 2 places in the future. Split it into a separate function. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-04-12lib/crc8: Add crc start valueStefan Roese
To make the usage of this function more flexible, lets add the CRC start value as parameter to this function. This way it can be used by other functions requiring different start values than 0 as well. For non-zero CRC start values to work, I've reworked the function a bit. The new implementation is copied from the Linux version in drivers/i2c/i2c-core.c / i2c_smbus_pec(). Which supports non-zero CRC stating values. I've double-checked that the results for zero starting values are identical to the results from the original version of this function. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-04-01efi_loader: Always allocate the highest available addressAlexander Graf
Some EFI applications (grub2) expect that an allocation always returns the highest available memory address for the given size. Without this, we may run into situations where the initrd gets allocated at a lower address than the kernel. This patch fixes booting in such situations for me. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-04-01lib/physmem.c: Switch to __weak for arch_phys_memsetTom Rini
We normally use __weak rather than calling it out directly as an alias. Update this function to the normal method. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-31cosmetic: Fix typos "privide"Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-27efi_loader: Fix some entry/exit pointsAlexander Graf
When switching between EFI context and U-Boot context we need to swap the register that "gd" resides in. Some functions slipped through here, with efi_allocate_pool / efi_free_pool not doing the switch correctly and efi_return_handle switching too often. Fix them all up to make sure we always have consistent register state. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-27efi_stub: Move carriage return before line feed in putc()Bin Meng
A carriage return needs to execute before a line feed. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27efi_loader: Add GOP supportAlexander Graf
The EFI standard defines a simple boot protocol that an EFI payload can use to access video output. This patch adds support to expose exactly that one (and the mode already in use) as possible graphical configuration to an EFI payload. With this, I can successfully run grub2 with graphical output. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-17cmd_dhry.c: Use lldiv for vax_mips calculation as wellTom Rini
Since dhry_per_sec is a u64 we must also use lldiv here when working with it. Otherwise: ../lib/dhry/cmd_dhry.c:(.text.do_dhry+0xd8): undefined reference to `__udivdi3' On some platforms. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-17x86: dts: Drop memory SPD compatible stringSimon Glass
This is not needed now that the memory controller driver has the SPD data in its own node. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17dhry: Correct dhrystone calculation for fast machinesSimon Glass
At present samus reports about 5600 DMIPS. With the default iteration count this is OK, but if 10 million runs are performed it overflows. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-17x86: Drop all the old pin configuration codeSimon Glass
We don't need this anymore - we can use device tree and the new pinconfig driver instead. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-16efi_loader: Pass proper device path in on bootAlexander Graf
EFI payloads can query for the device they were booted from. Because we have a disconnect between loading binaries and running binaries, we passed in a dummy device path so far. Unfortunately that breaks grub2's logic to find its configuration file from the same device it was booted from. This patch adds logic to have the "load" command call into our efi code to set the device path to the one we last loaded a binary from. With this grub2 properly detects where we got booted from and can find its configuration file, even when searching by-partition. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-16efi_loader: hook up in build environmentAlexander Graf
Now that we have all the bits and pieces ready for EFI payload loading support, hook them up in Makefiles and KConfigs so that we can build. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> [trini: Enable only when we of OF_LIBFDT, disable on kwb and colibri_pxa270] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16efi_loader: Implement memory allocation and mapAlexander Graf
The EFI loader needs to maintain views of memory - general system memory windows as well as used locations inside those and potential runtime service MMIO windows. To manage all of these, add a few helpers that maintain an internal representation of the map the similar to how the EFI API later on reports it to the application. For allocations, the scheme is very simple. We basically allow allocations to replace chunks of previously done maps, so that a new LOADER_DATA allocation for example can remove a piece of the RAM map. When no specific address is given, we just take the highest possible address in the lowest RAM map that fits the allocation size. Signed-off-by: Alexander Graf <agraf@suse.de> Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15efi_loader: Add disk interfacesAlexander Graf
A EFI applications usually want to access storage devices to load data from. This patch adds support for EFI disk interfaces. It loops through all block storage interfaces known to U-Boot and creates an EFI object for each existing one. EFI applications can then through these objects call U-Boot's read and write functions. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> [trini: Update for various DM changes since posting] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-15efi_loader: Add runtime servicesAlexander Graf
After booting has finished, EFI allows firmware to still interact with the OS using the "runtime services". These callbacks live in a separate address space, since they are available long after U-Boot has been overwritten by the OS. This patch adds enough framework for arbitrary code inside of U-Boot to become a runtime service with the right section attributes set. For now, we don't make use of it yet though. We could maybe in the future map U-boot environment variables to EFI variables here. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15efi_loader: Add console interfaceAlexander Graf
One of the basic EFI interfaces is the console interface. Using it an EFI application can interface with the user. This patch implements an EFI console interface using getc() and putc(). Today, we only implement text based consoles. We also convert the EFI Unicode characters to UTF-8 on the fly, hoping that everyone managed to jump on the train by now. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15efi_loader: Add boot time servicesAlexander Graf
When an EFI application runs, it has access to a few descriptor and callback tables to instruct the EFI compliant firmware to do things for it. The bulk of those interfaces are "boot time services". They handle all object management, and memory allocation. This patch adds support for the boot time services and also exposes a system table, which is the point of entry descriptor table for EFI payloads. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15efi_loader: Add PE image loaderAlexander Graf
EFI uses the PE binary format for its application images. Add support to EFI PE binaries as well as all necessary bits for the "EFI image loader" interfaces. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-03-14Merge git://git.denx.de/u-boot-dmTom Rini
2016-03-14lib/crc16.c: Rename cyg_crc16() to crc16_ccitt() and add crc start valueStefan Roese
The original name of this function is unclear. This patch renames this CRC16 function to crc16_ccitt() matching its name with its implementation. To make the usage of this function more flexible, lets add the CRC start value as parameter to this function. This way it can be used by other functions requiring different start values than 0 as well. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14lib/crc16.c: Coding-style cleanupStefan Roese
lib/crc16.c is changed to match the common U-Boot coding-style. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14fdt: Allow libfdt to be used in SPLSimon Glass
Add an option to enable libfdt in SPL. This can be useful when decoding FIT files in SPL. We need to make sure this option is not enabled in SPL by this change. Also this option needs to be enabled in host builds. Si add a new IMAGE_USE_LIBFDT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14dm: fdtdec: Correct a sandbox build warningSimon Glass
Adjust the cast to avoid a warning when stdint.h is used. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14dm: Drop the block_dev_desc_t typedefSimon Glass
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long and causes 80-column violations, rename it to struct blk_desc. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
2016-03-14dm: Use uclass_first_device_err() where it is usefulSimon Glass
Use this new function in places where it simplifies the code. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14Move CONFIG_OF_LIBFDT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing boards. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14libfdt: Add a function to write a property placeholderSimon Glass
The existing function to add a new property to a tree being built requires that the entire contents of the new property be passed in. For some applications it is more convenient to be able to add the property contents later, perhaps by reading from a file. This avoids double-buffering of the contents. Add a new function to support this and adust the existing fdt_property() to use it. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-02-26timer: Provide an early timerSimon Glass
In some cases the timer must be accessible before driver model is active. Examples include when using CONFIG_TRACE to trace U-Boot's execution before driver model is set up. Enable this option to use an early timer. These functions must be supported by your timer driver: timer_early_get_count() and timer_early_get_rate(). Signed-off-by: Simon Glass <sjg@chromium.org>
2016-02-26lib: Don't instrument the div64 functionSimon Glass
This function can be called from the timer code on instrumented functions. Mark it as 'notrace' so that it doesn't cause infinite recursion. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-16tegra: nyan-big: Move the LCD driver to driver modelSimon Glass
Adjust the driver to use driver model. The SOR becomes a bridge device. We use the normal simple_panel driver to handle the display itself. We also need to enable some options such as regulators, PWMs and DM_VIDEO itself. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-15Makefile: remove BUILD_TAG from KBUILD_CFLAGSStephen Warren
If BUILD_TAG is part of KBUILD_CFLAGS, then any time the value changes, all files get rebuilt. In a continuous integration environment, the value will change every build. This wastes time, assuming that incremental builds would otherwise occur. To solve this, remove BUILD_TAG from KBUILD_CFLAGS and add it to CFLAGS for just the one file that uses it. This does have the disadvantage that if any other files want to use the flag, we'll need to duplicate this custom CFLAGS setup logic. However, it seems unlikely we'll need this. An alternative would be to add BUILD_TAG to the "local version" and remove the special case code from display_options.c. However, that would affect the format of the U-Boot signon message, which may negatively affect people looking for specific data there. The approach of using file-specific CFLAGS was suggested by Masahiro Yamada. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>