diff options
author | Simon Glass <sjg@chromium.org> | 2017-07-24 03:19:40 (GMT) |
---|---|---|
committer | Tom Rini <trini@konsulko.com> | 2017-07-26 01:08:07 (GMT) |
commit | e73496d08e2dc60f3e00554c71b92f72cdebf0fd (patch) | |
tree | 1ff064e00f57e6f7a38aff40dce30b2b0d8289bf /README | |
parent | 2be296538e2e9d2893dc495b3fc8f9f6acb1454c (diff) | |
download | u-boot-fsl-qoriq-e73496d08e2dc60f3e00554c71b92f72cdebf0fd.tar.xz |
env: Move help from README to Kconfig
The CONFIG_ENV_IS_IN_... options which have already been converted to
Kconfig only have a small amount of help. Move the rest of it over from
the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Diffstat (limited to 'README')
-rw-r--r-- | README | 114 |
1 files changed, 0 insertions, 114 deletions
@@ -3634,75 +3634,12 @@ BE CAREFUL! For some special cases, the local device can not use environment stored in a remote NOR flash by SRIO or PCIE link, but it can not erase, write this NOR flash by SRIO or PCIE interface. -- CONFIG_ENV_IS_IN_NAND: - - Define this if you have a NAND device which you want to use - for the environment. - - - CONFIG_ENV_OFFSET: - - CONFIG_ENV_SIZE: - - These two #defines specify the offset and size of the environment - area within the first NAND device. CONFIG_ENV_OFFSET must be - aligned to an erase block boundary. - - - CONFIG_ENV_OFFSET_REDUND (optional): - - This setting describes a second storage area of CONFIG_ENV_SIZE - size used to hold a redundant copy of the environment data, so - that there is a valid backup copy in case there is a power failure - during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be - aligned to an erase block boundary. - - - CONFIG_ENV_RANGE (optional): - - Specifies the length of the region in which the environment - can be written. This should be a multiple of the NAND device's - block size. Specifying a range with more erase blocks than - are needed to hold CONFIG_ENV_SIZE allows bad blocks within - the range to be avoided. - - - CONFIG_ENV_OFFSET_OOB (optional): - - Enables support for dynamically retrieving the offset of the - environment from block zero's out-of-band data. The - "nand env.oob" command can be used to record this offset. - Currently, CONFIG_ENV_OFFSET_REDUND is not supported when - using CONFIG_ENV_OFFSET_OOB. - - CONFIG_NAND_ENV_DST Defines address in RAM to which the nand_spl code should copy the environment. If redundant environment is used, it will be copied to CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE. -- CONFIG_ENV_IS_IN_UBI: - - Define this if you have an UBI volume that you want to use for the - environment. This has the benefit of wear-leveling the environment - accesses, which is important on NAND. - - - CONFIG_ENV_UBI_PART: - - Define this to a string that is the mtd partition containing the UBI. - - - CONFIG_ENV_UBI_VOLUME: - - Define this to the name of the volume that you want to store the - environment in. - - - CONFIG_ENV_UBI_VOLUME_REDUND: - - Define this to the name of another volume to store a second copy of - the environment in. This will enable redundant environments in UBI. - It is assumed that both volumes are in the same MTD partition. - - - CONFIG_UBI_SILENCE_MSG - - CONFIG_UBIFS_SILENCE_MSG - - You will probably want to define these to avoid a really noisy system - when storing the env in UBI. - - CONFIG_ENV_IS_IN_FAT: Define this if you want to use the FAT file system for the environment. @@ -3734,57 +3671,6 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface. - CONFIG_FAT_WRITE: This must be enabled. Otherwise it cannot save the environment file. -- CONFIG_ENV_IS_IN_MMC: - - Define this if you have an MMC device which you want to use for the - environment. - - - CONFIG_SYS_MMC_ENV_DEV: - - Specifies which MMC device the environment is stored in. - - - CONFIG_SYS_MMC_ENV_PART (optional): - - Specifies which MMC partition the environment is stored in. If not - set, defaults to partition 0, the user area. Common values might be - 1 (first MMC boot partition), 2 (second MMC boot partition). - - - CONFIG_ENV_OFFSET: - - CONFIG_ENV_SIZE: - - These two #defines specify the offset and size of the environment - area within the specified MMC device. - - If offset is positive (the usual case), it is treated as relative to - the start of the MMC partition. If offset is negative, it is treated - as relative to the end of the MMC partition. This can be useful if - your board may be fitted with different MMC devices, which have - different sizes for the MMC partitions, and you always want the - environment placed at the very end of the partition, to leave the - maximum possible space before it, to store other data. - - These two values are in units of bytes, but must be aligned to an - MMC sector boundary. - - - CONFIG_ENV_OFFSET_REDUND (optional): - - Specifies a second storage area, of CONFIG_ENV_SIZE size, used to - hold a redundant copy of the environment data. This provides a - valid backup copy in case the other copy is corrupted, e.g. due - to a power failure during a "saveenv" operation. - - This value may also be positive or negative; this is handled in the - same way as CONFIG_ENV_OFFSET. - - This value is also in units of bytes, but must also be aligned to - an MMC sector boundary. - - - CONFIG_ENV_SIZE_REDUND (optional): - - This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is - set. If this value is set, it must be set to the same value as - CONFIG_ENV_SIZE. - Please note that the environment is read-only until the monitor has been relocated to RAM and a RAM copy of the environment has been created; also, when using EEPROM you will have to use getenv_f() |