Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: device tree work" from Arnd Bergmann:
 "Most of these patches convert code from using static platform data to
  describing the hardware in the device tree.  This is only the first
  half of the changes for v3.4 because a lot of patches for this topic
  came in the last week before the merge window.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
  Document: devicetree: add OF documents for arch-mmp
  ARM: dts: append DTS file of pxa168
  ARM: mmp: append OF support on pxa168
  ARM: mmp: enable rtc clk in pxa168
  i2c: pxa: add OF support
  serial: pxa: add OF support
  arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
  ARM: OMAP2+: Remove extra ifdefs for board-generic
  ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
  ASoC: DT: Add digital microphone binding to PAZ00 board.
  ARM: dt: Add ARM PMU to tegra*.dtsi
  ARM: at91: at91sam9x5cm/dt: add leds support
  ARM: at91: usb_a9g20/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add leds support
  ARM: at91: usb_a9g20/dt: add leds support
  ARM: at91/pio: add new PIO3 features
  ARM: at91: add sam9_smc.o to at91sam9x5 build
  ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
  ARM: at91/tc: add device tree support to atmel_tclib
  ...

6 files changed, 271 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt
new file mode 100644
index 0000000..aabca4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt
@@ -0,0 +1,38 @@
+* Advanced Interrupt Controller (AIC)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-aic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: For single AIC system, it is an empty property.
+- #interrupt-cells: The number of cells to define the interrupts. It sould be 2.
+  The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+      Default flag for internal sources should be set to 4 (active high).
+- reg: Should contain AIC registers location and length
+
+Examples:
+	/*
+	 * AIC
+	 */
+	aic: interrupt-controller@fffff000 {
+		compatible = "atmel,at91rm9200-aic";
+		interrupt-controller;
+		interrupt-parent;
+		#interrupt-cells = <2>;
+		reg = <0xfffff000 0x200>;
+	};
+
+	/*
+	 * An interrupt generating device that is wired to an AIC.
+	 */
+	dma: dma-controller@ffffec00 {
+		compatible = "atmel,at91sam9g45-dma";
+		reg = <0xffffec00 0x200>;
+		interrupts = <21 4>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
new file mode 100644
index 0000000..1aeaf6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -0,0 +1,32 @@
+Atmel AT91 device tree bindings.
+================================
+
+PIT Timer required properties:
+- compatible: Should be "atmel,at91sam9260-pit"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the PIT which is the IRQ line
+  shared across all System Controller members.
+
+TC/TCLIB Timer required properties:
+- compatible: Should be "atmel,<chip>-pit".
+  <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- interrupts: Should contain all interrupts for the TC block
+  Note that you can specify several interrupt cells if the TC
+  block has one interrupt per channel.
+
+Examples:
+
+One interrupt per TC block:
+	tcb0: timer@fff7c000 {
+		compatible = "atmel,at91rm9200-tcb";
+		reg = <0xfff7c000 0x100>;
+		interrupts = <18 4>;
+	};
+
+One interrupt per TC channel in a TC block:
+	tcb1: timer@fffdc000 {
+		compatible = "atmel,at91rm9200-tcb";
+		reg = <0xfffdc000 0x100>;
+		interrupts = <26 4 27 4 28 4>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index 54bddda..bfbc771 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -28,3 +28,25 @@ Required root node properties:
 i.MX6 Quad SABRE Lite Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+
+Generic i.MX boards
+-------------------
+
+No iomux setup is done for these boards, so this must have been configured
+by the bootloader for boards to work with the generic bindings.
+
+i.MX27 generic board
+Required root node properties:
+    - compatible = "fsl,imx27";
+
+i.MX51 generic board
+Required root node properties:
+    - compatible = "fsl,imx51";
+
+i.MX53 generic board
+Required root node properties:
+    - compatible = "fsl,imx53";
+
+i.MX6q generic board
+Required root node properties:
+    - compatible = "fsl,imx6q";
diff --git a/Documentation/devicetree/bindings/arm/mrvl.txt b/Documentation/devicetree/bindings/arm/mrvl.txt
new file mode 100644
index 0000000..d8de933
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mrvl.txt
@@ -0,0 +1,6 @@
+Marvell Platforms Device Tree Bindings
+----------------------------------------------------
+
+PXA168 Aspenite Board
+Required root node properties:
+	- compatible = "mrvl,pxa168-aspenite", "mrvl,pxa168";
diff --git a/Documentation/devicetree/bindings/arm/omap/intc.txt b/Documentation/devicetree/bindings/arm/omap/intc.txt
new file mode 100644
index 0000000..f2583e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/intc.txt
@@ -0,0 +1,27 @@
+* OMAP Interrupt Controller
+
+OMAP2/3 are using a TI interrupt controller that can support several
+configurable number of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+	"ti,omap2-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+
+  The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+	intc: interrupt-controller@1 {
+		compatible = "ti,omap2-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		ti,intc-size = <96>;
+		reg = <0x48200000 0x1000>;
+	};
+
diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt
new file mode 100644
index 0000000..ec8b50c
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/vexpress.txt
@@ -0,0 +1,146 @@
+ARM Versatile Express boards family
+-----------------------------------
+
+ARM's Versatile Express platform consists of a motherboard and one
+or more daughterboards (tiles). The motherboard provides a set of
+peripherals. Processor and RAM "live" on the tiles.
+
+The motherboard and each core tile should be described by a separate
+Device Tree source file, with the tile's description including
+the motherboard file using a /include/ directive. As the motherboard
+can be initialized in one of two different configurations ("memory
+maps"), care must be taken to include the correct one.
+
+Required properties in the root node:
+- compatible value:
+	compatible = "arm,vexpress,<model>", "arm,vexpress";
+  where <model> is the full tile model name (as used in the tile's
+    Technical Reference Manual), eg.:
+    - for Coretile Express A5x2 (V2P-CA5s):
+	compatible = "arm,vexpress,v2p-ca5s", "arm,vexpress";
+    - for Coretile Express A9x4 (V2P-CA9):
+	compatible = "arm,vexpress,v2p-ca9", "arm,vexpress";
+  If a tile comes in several variants or can be used in more then one
+  configuration, the compatible value should be:
+	compatible = "arm,vexpress,<model>,<variant>", \
+				"arm,vexpress,<model>", "arm,vexpress";
+  eg:
+    - Coretile Express A15x2 (V2P-CA15) with Tech Chip 1:
+	compatible = "arm,vexpress,v2p-ca15,tc1", \
+				"arm,vexpress,v2p-ca15", "arm,vexpress";
+    - LogicTile Express 13MG (V2F-2XV6) running Cortex-A7 (3 cores) SMM:
+	compatible = "arm,vexpress,v2f-2xv6,ca7x3", \
+				"arm,vexpress,v2f-2xv6", "arm,vexpress";
+
+Optional properties in the root node:
+- tile model name (use name from the tile's Technical Reference
+  Manual, eg. "V2P-CA5s")
+	model = "<model>";
+- tile's HBI number (unique ARM's board model ID, visible on the
+  PCB's silkscreen) in hexadecimal transcription:
+	arm,hbi = <0xhbi>
+  eg:
+  - for Coretile Express A5x2 (V2P-CA5s) HBI-0191:
+	arm,hbi = <0x191>;
+  - Coretile Express A9x4 (V2P-CA9) HBI-0225:
+	arm,hbi = <0x225>;
+
+Top-level standard "cpus" node is required. It must contain a node
+with device_type = "cpu" property for every available core, eg.:
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a5";
+			reg = <0>;
+		};
+	};
+
+The motherboard description file provides a single "motherboard" node
+using 2 address cells corresponding to the Static Memory Bus used
+between the motherboard and the tile. The first cell defines the Chip
+Select (CS) line number, the second cell address offset within the CS.
+All interrupt lines between the motherboard and the tile are active
+high and are described using single cell.
+
+Optional properties of the "motherboard" node:
+- motherboard's memory map variant:
+	arm,v2m-memory-map = "<name>";
+  where name is one of:
+  - "rs1" - for RS1 map (i.a. peripherals on CS3); this map is also
+            referred to as "ARM Cortex-A Series memory map":
+	arm,v2m-memory-map = "rs1";
+  When this property is missing, the motherboard is using the original
+  memory map (also known as the "Legacy memory map", primarily used
+  with the original CoreTile Express A9x4) with peripherals on CS7.
+
+Motherboard .dtsi files provide a set of labelled peripherals that
+can be used to obtain required phandle in the tile's "aliases" node:
+- UARTs, note that the numbers correspond to the physical connectors
+  on the motherboard's back panel:
+	v2m_serial0, v2m_serial1, v2m_serial2 and v2m_serial3
+- I2C controllers:
+	v2m_i2c_dvi and v2m_i2c_pcie
+- SP804 timers:
+	v2m_timer01 and v2m_timer23
+
+Current Linux implementation requires a "arm,v2m_timer" alias
+pointing at one of the motherboard's SP804 timers, if it is to be
+used as the system timer. This alias should be defined in the
+motherboard files.
+
+The tile description must define "ranges", "interrupt-map-mask" and
+"interrupt-map" properties to translate the motherboard's address
+and interrupt space into one used by the tile's processor.
+
+Abbreviated example:
+
+/dts-v1/;
+
+/ {
+	model = "V2P-CA5s";
+	arm,hbi = <0x225>;
+	compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen { };
+
+	aliases {
+		serial0 = &v2m_serial0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a5";
+			reg = <0>;
+		};
+	};
+
+	gic: interrupt-controller@2c001000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x2c001000 0x1000>,
+		      <0x2c000100 0x100>;
+	};
+
+	motherboard {
+		/* CS0 is visible at 0x08000000 */
+		ranges = <0 0 0x08000000 0x04000000>;
+		interrupt-map-mask = <0 0 63>;
+		/* Active high IRQ 0 is connected to GIC's SPI0 */
+		interrupt-map = <0 0 0 &gic 0 0 4>;
+	};
+};
+
+/include/ "vexpress-v2m-rs1.dtsi"