Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Clearly mark ACPI drivers as such
  i2c: Add driver for SMBus Control Method Interface
  i2c-pnx: Correct use of request_region/request_mem_region
  MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
  i2c-piix4: Add AMD SB900 SMBus device ID
  i2c/chips: Remove deprecated pcf8574 driver
  i2c/chips: Remove deprecated pca9539 driver
  i2c/chips: Remove deprecated pcf8575 driver
  gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
  i2c/scx200_acb: Provide more information on bus errors
  i2c: Provide compatibility links for i2c adapters
  i2c: Convert i2c adapters to bus devices
  i2c: Convert i2c clients to a device type
  i2c/tsl2550: Use combined SMBus transactions
  i2c-taos-evm: Switch echo off to improve performance
  i2c: Drop unused i2c_driver.id field

1 files changed, 0 insertions, 58 deletions

diff --git a/Documentation/i2c/chips/pca9539 b/Documentation/i2c/chips/pca9539
deleted file mode 100644
index 6aff890..0000000
--- a/Documentation/i2c/chips/pca9539
+++ /dev/null
@@ -1,58 +0,0 @@
-Kernel driver pca9539
-=====================
-
-NOTE: this driver is deprecated and will be dropped soon, use
-drivers/gpio/pca9539.c instead.
-
-Supported chips:
-  * Philips PCA9539
-    Prefix: 'pca9539'
-    Addresses scanned: none
-    Datasheet:
-        http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf
-
-Author: Ben Gardner <bgardner@wabtec.com>
-
-
-Description
------------
-
-The Philips PCA9539 is a 16 bit low power I/O device.
-All 16 lines can be individually configured as an input or output.
-The input sense can also be inverted.
-The 16 lines are split between two bytes.
-
-
-Detection
----------
-
-The PCA9539 is difficult to detect and not commonly found in PC machines,
-so you have to pass the I2C bus and address of the installed PCA9539
-devices explicitly to the driver at load time via the force=... parameter.
-
-
-Sysfs entries
--------------
-
-Each is a byte that maps to the 8 I/O bits.
-A '0' suffix is for bits 0-7, while '1' is for bits 8-15.
-
-input[01]     - read the current value
-output[01]    - sets the output value
-direction[01] - direction of each bit: 1=input, 0=output
-invert[01]    - toggle the input bit sense
-
-input reads the actual state of the line and is always available.
-The direction defaults to input for all channels.
-
-
-General Remarks
----------------
-
-Note that each output, direction, and invert entry controls 8 lines.
-You should use the read, modify, write sequence.
-For example. to set output bit 0 of 1.
-  val=$(cat output0)
-  val=$(( $val | 1 ))
-  echo $val > output0
-