Merge tag 'cris-for-3.12' of git://jni.nu/cris

Pull CRIS updates from Jesper Nilsson:
 "Mostly cleanup and removal of unused configs"

* tag 'cris-for-3.12' of git://jni.nu/cris:
  CRIS: drop unused Kconfig symbols
  CRIS: Add kvm_para.h which includes generic file
  CRIS: remove unused current_regs
  CRIS: Remove last traces of legacy RTC drivers
  CRIS: remove "config OOM_REBOOT"

2 files changed, 0 insertions, 72 deletions

diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index daf5f19..239dab0 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -417,16 +417,6 @@ config ETRAX_USB_HOST
 	   for CTRL and BULK traffic only, INTR traffic may work as well
 	   however (depending on the requirements of timeliness).
 
-config ETRAX_USB_HOST_PORT1
-	bool "USB port 1 enabled"
-	depends on ETRAX_USB_HOST
-	default n
-
-config ETRAX_USB_HOST_PORT2
-	bool "USB port 2 enabled"
-	depends on ETRAX_USB_HOST
-	default n
-
 config ETRAX_PTABLE_SECTOR
 	int "Byte-offset of partition table sector"
 	depends on ETRAX_AXISFLASHMAP
@@ -527,19 +517,6 @@ config ETRAX_GPIO
 	  Remember that you need to setup the port directions appropriately in
 	  the General configuration.
 
-config ETRAX_PA_BUTTON_BITMASK
-	hex "PA-buttons bitmask"
-	depends on ETRAX_GPIO
-	default "02"
-	help
-	  This is a bitmask with information about what bits on PA that
-	  are used for buttons.
-	  Most products has a so called TEST button on PA1, if that's true
-	  use 02 here.
-	  Use 00 if there are no buttons on PA.
-	  If the bitmask is <> 00 a button driver will be included in the gpio
-	  driver. ETRAX general I/O support must be enabled.
-
 config ETRAX_PA_CHANGEABLE_DIR
 	hex "PA user changeable dir mask"
 	depends on ETRAX_GPIO
@@ -580,51 +557,4 @@ config ETRAX_PB_CHANGEABLE_BITS
 	  Bit set = changeable.
 	  You probably want 00 here.
 
-config ETRAX_DS1302_RST_ON_GENERIC_PORT
-	bool "DS1302 RST on Generic Port"
-	depends on ETRAX_DS1302
-	help
-	  If your product has the RST signal line for the DS1302 RTC on the
-	  Generic Port then say Y here, otherwise leave it as N in which
-	  case the RST signal line is assumed to be connected to Port PB
-	  (just like the SCL and SDA lines).
-
-config ETRAX_DS1302_RSTBIT
-	int "DS1302 RST bit number"
-	depends on ETRAX_DS1302
-	default "2"
-	help
-	  This is the bit number for the RST signal line of the DS1302 RTC on
-	  the selected port. If you have selected the generic port then it
-	  should be bit 27, otherwise your best bet is bit 5.
-
-config ETRAX_DS1302_SCLBIT
-	int "DS1302 SCL bit number"
-	depends on ETRAX_DS1302
-	default "1"
-	help
-	  This is the bit number for the SCL signal line of the DS1302 RTC on
-	  Port PB. This is probably best left at 3.
-
-config ETRAX_DS1302_SDABIT
-	int "DS1302 SDA bit number"
-	depends on ETRAX_DS1302
-	default "0"
-	help
-	  This is the bit number for the SDA signal line of the DS1302 RTC on
-	  Port PB. This is probably best left at 2.
-
-config ETRAX_DS1302_TRICKLE_CHARGE
-	int "DS1302 Trickle charger value"
-	depends on ETRAX_DS1302
-	default "0"
-	help
-	  This controls the initial value of the trickle charge register.
-	  0 = disabled (use this if you are unsure or have a non rechargeable battery)
-	  Otherwise the following values can be OR:ed together to control the
-	  charge current:
-	  1 = 2kohm, 2 = 4kohm, 3 = 4kohm
-	  4 = 1 diode, 8 = 2 diodes
-	  Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
-
 endif
diff --git a/arch/cris/arch-v10/drivers/Makefile b/arch/cris/arch-v10/drivers/Makefile
index 44bf2e8..e5c1318 100644
--- a/arch/cris/arch-v10/drivers/Makefile
+++ b/arch/cris/arch-v10/drivers/Makefile
@@ -6,7 +6,5 @@ obj-$(CONFIG_ETRAX_AXISFLASHMAP)	+= axisflashmap.o
 obj-$(CONFIG_ETRAX_I2C)			+= i2c.o
 obj-$(CONFIG_ETRAX_I2C_EEPROM)		+= eeprom.o
 obj-$(CONFIG_ETRAX_GPIO)		+= gpio.o
-obj-$(CONFIG_ETRAX_DS1302)		+= ds1302.o
-obj-$(CONFIG_ETRAX_PCF8563)		+= pcf8563.o
 obj-$(CONFIG_ETRAX_SYNCHRONOUS_SERIAL)	+= sync_serial.o