diff options
author | Paul Mackerras <paulus@samba.org> | 2005-11-08 00:14:20 (GMT) |
---|---|---|
committer | Paul Mackerras <paulus@samba.org> | 2005-11-08 00:14:20 (GMT) |
commit | 24bfb00123e82a2e70bd115277d922438813515b (patch) | |
tree | 27328b8a5718e16d64e2d101f4b7ddcad5930aed /arch/ppc | |
parent | c6135234550ed89a6fd0e8cb229633967e41d649 (diff) | |
parent | 3f00d3e8fb963968a922d821a9a53b503b687e81 (diff) | |
download | linux-fsl-qoriq-24bfb00123e82a2e70bd115277d922438813515b.tar.xz |
Merge ../linux-2.6
Diffstat (limited to 'arch/ppc')
39 files changed, 2789 insertions, 228 deletions
diff --git a/arch/ppc/4xx_io/serial_sicc.c b/arch/ppc/4xx_io/serial_sicc.c index e95c48d..84d96b8 100644 --- a/arch/ppc/4xx_io/serial_sicc.c +++ b/arch/ppc/4xx_io/serial_sicc.c @@ -1145,8 +1145,8 @@ static int set_serial_info(struct SICC_info *info, info->flags = ((state->flags & ~ASYNC_INTERNAL_FLAGS) | (info->flags & ASYNC_INTERNAL_FLAGS)); state->custom_divisor = new_serial.custom_divisor; - state->close_delay = new_serial.close_delay * HZ / 100; - state->closing_wait = new_serial.closing_wait * HZ / 100; + state->close_delay = msecs_to_jiffies(10 * new_serial.close_delay); + state->closing_wait = msecs_to_jiffies(10 * new_serial.closing_wait); info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; port->fifosize = new_serial.xmit_fifo_size; @@ -1465,10 +1465,8 @@ static void siccuart_close(struct tty_struct *tty, struct file *filp) info->event = 0; info->tty = NULL; if (info->blocked_open) { - if (info->state->close_delay) { - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(info->state->close_delay); - } + if (info->state->close_delay) + schedule_timeout_interruptible(info->state->close_delay); wake_up_interruptible(&info->open_wait); } info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); @@ -1496,7 +1494,7 @@ static void siccuart_wait_until_sent(struct tty_struct *tty, int timeout) * Note: we have to use pretty tight timings here to satisfy * the NIST-PCTS. */ - char_time = (info->timeout - HZ/50) / info->port->fifosize; + char_time = (info->timeout - msecs_to_jiffies(20)) / info->port->fifosize; char_time = char_time / 5; if (char_time == 0) char_time = 1; @@ -1521,8 +1519,7 @@ static void siccuart_wait_until_sent(struct tty_struct *tty, int timeout) tty->index, jiffies, expire, char_time); while ((readb(info->port->uart_base + BL_SICC_LSR) & _LSR_TX_ALL) != _LSR_TX_ALL) { - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(char_time); + schedule_timeout_interruptible(char_time); if (signal_pending(current)) break; if (timeout && time_after(jiffies, expire)) @@ -1773,7 +1770,7 @@ int __init siccuart_init(void) for (i = 0; i < SERIAL_SICC_NR; i++) { struct SICC_state *state = sicc_state + i; state->line = i; - state->close_delay = 5 * HZ / 10; + state->close_delay = msecs_to_jiffies(500); state->closing_wait = 30 * HZ; spin_lock_init(&state->sicc_lock); } diff --git a/arch/ppc/8260_io/fcc_enet.c b/arch/ppc/8260_io/fcc_enet.c index 2086c6a..4edeede 100644 --- a/arch/ppc/8260_io/fcc_enet.c +++ b/arch/ppc/8260_io/fcc_enet.c @@ -1309,8 +1309,7 @@ static void mii_dm9161_wait(uint mii_reg, struct net_device *dev) /* Davicom takes a bit to come up after a reset, * so wait here for a bit */ - set_current_state(TASK_UNINTERRUPTIBLE); - schedule_timeout(timeout); + schedule_timeout_uninterruptible(timeout); } static phy_info_t phy_info_dm9161 = { diff --git a/arch/ppc/8xx_io/cs4218_tdm.c b/arch/ppc/8xx_io/cs4218_tdm.c index 532caa3..49eb2a7 100644 --- a/arch/ppc/8xx_io/cs4218_tdm.c +++ b/arch/ppc/8xx_io/cs4218_tdm.c @@ -1013,8 +1013,7 @@ static void CS_IrqCleanup(void) */ cpm_free_handler(CPMVEC_SMC2); - if (beep_buf) - kfree(beep_buf); + kfree(beep_buf); kd_mksound = orig_mksound; } #endif /* MODULE */ diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig index 114b90f..8fa51b0 100644 --- a/arch/ppc/Kconfig +++ b/arch/ppc/Kconfig @@ -746,6 +746,16 @@ config MPC834x bool default y if MPC834x_SYS +config CPM1 + bool + depends on 8xx + default y + help + The CPM1 (Communications Processor Module) is a coprocessor on + embedded CPUs made by Motorola. Selecting this option means that + you wish to build a kernel for a machine with a CPM1 coprocessor + on it (8xx, 827x, 8560). + config CPM2 bool depends on 8260 || MPC8560 || MPC8555 @@ -1247,6 +1257,14 @@ source "drivers/pci/Kconfig" source "drivers/pcmcia/Kconfig" +config RAPIDIO + bool "RapidIO support" if MPC8540 || MPC8560 + help + If you say Y here, the kernel will include drivers and + infrastructure code to support RapidIO interconnect devices. + +source "drivers/rapidio/Kconfig" + endmenu menu "Advanced setup" diff --git a/arch/ppc/boot/simple/Makefile b/arch/ppc/boot/simple/Makefile index b7bd8f6..82df88b 100644 --- a/arch/ppc/boot/simple/Makefile +++ b/arch/ppc/boot/simple/Makefile @@ -67,6 +67,12 @@ zimageinitrd-$(CONFIG_BAMBOO) := zImage.initrd-TREE entrypoint-$(CONFIG_BAMBOO) := 0x01000000 extra.o-$(CONFIG_BAMBOO) := pibs.o + zimage-$(CONFIG_BUBINGA) := zImage-TREE +zimageinitrd-$(CONFIG_BUBINGA) := zImage.initrd-TREE + end-$(CONFIG_BUBINGA) := bubinga + entrypoint-$(CONFIG_BUBINGA) := 0x01000000 + extra.o-$(CONFIG_BUBINGA) := openbios.o + zimage-$(CONFIG_EBONY) := zImage-TREE zimageinitrd-$(CONFIG_EBONY) := zImage.initrd-TREE end-$(CONFIG_EBONY) := ebony @@ -79,12 +85,30 @@ zimageinitrd-$(CONFIG_LUAN) := zImage.initrd-TREE entrypoint-$(CONFIG_LUAN) := 0x01000000 extra.o-$(CONFIG_LUAN) := pibs.o + zimage-$(CONFIG_YUCCA) := zImage-TREE +zimageinitrd-$(CONFIG_YUCCA) := zImage.initrd-TREE + end-$(CONFIG_YUCCA) := yucca + entrypoint-$(CONFIG_YUCCA) := 0x01000000 + extra.o-$(CONFIG_YUCCA) := pibs.o + zimage-$(CONFIG_OCOTEA) := zImage-TREE zimageinitrd-$(CONFIG_OCOTEA) := zImage.initrd-TREE end-$(CONFIG_OCOTEA) := ocotea entrypoint-$(CONFIG_OCOTEA) := 0x01000000 extra.o-$(CONFIG_OCOTEA) := pibs.o + zimage-$(CONFIG_SYCAMORE) := zImage-TREE +zimageinitrd-$(CONFIG_SYCAMORE) := zImage.initrd-TREE + end-$(CONFIG_SYCAMORE) := sycamore + entrypoint-$(CONFIG_SYCAMORE) := 0x01000000 + extra.o-$(CONFIG_SYCAMORE) := openbios.o + + zimage-$(CONFIG_WALNUT) := zImage-TREE +zimageinitrd-$(CONFIG_WALNUT) := zImage.initrd-TREE + end-$(CONFIG_WALNUT) := walnut + entrypoint-$(CONFIG_WALNUT) := 0x01000000 + extra.o-$(CONFIG_WALNUT) := openbios.o + extra.o-$(CONFIG_EV64260) := misc-ev64260.o end-$(CONFIG_EV64260) := ev64260 cacheflag-$(CONFIG_EV64260) := -include $(clear_L2_L3) @@ -162,7 +186,8 @@ OBJCOPY_ARGS := -O elf32-powerpc # head.o and relocate.o must be at the start. boot-y := head.o relocate.o $(extra.o-y) $(misc-y) -boot-$(CONFIG_40x) += embed_config.o +boot-$(CONFIG_REDWOOD_5) += embed_config.o +boot-$(CONFIG_REDWOOD_6) += embed_config.o boot-$(CONFIG_8xx) += embed_config.o boot-$(CONFIG_8260) += embed_config.o boot-$(CONFIG_BSEIP) += iic.o diff --git a/arch/ppc/boot/simple/misc.c b/arch/ppc/boot/simple/misc.c index e02de5b..f415d6c 100644 --- a/arch/ppc/boot/simple/misc.c +++ b/arch/ppc/boot/simple/misc.c @@ -23,7 +23,7 @@ #include <asm/page.h> #include <asm/mmu.h> #include <asm/bootinfo.h> -#ifdef CONFIG_44x +#ifdef CONFIG_4xx #include <asm/ibm4xx.h> #endif #include <asm/reg.h> @@ -88,6 +88,14 @@ get_mem_size(void) return 0; } +#if defined(CONFIG_40x) +#define PPC4xx_EMAC0_MR0 EMAC0_BASE +#endif + +#if defined(CONFIG_44x) && defined(PPC44x_EMAC0_MR0) +#define PPC4xx_EMAC0_MR0 PPC44x_EMAC0_MR0 +#endif + struct bi_record * decompress_kernel(unsigned long load_addr, int num_words, unsigned long cksum) { @@ -103,13 +111,13 @@ decompress_kernel(unsigned long load_addr, int num_words, unsigned long cksum) com_port = serial_init(0, NULL); #endif -#if defined(CONFIG_44x) && defined(PPC44x_EMAC0_MR0) +#if defined(PPC4xx_EMAC0_MR0) /* Reset MAL */ mtdcr(DCRN_MALCR(DCRN_MAL_BASE), MALCR_MMSR); /* Wait for reset */ while (mfdcr(DCRN_MALCR(DCRN_MAL_BASE)) & MALCR_MMSR) {}; /* Reset EMAC */ - *(volatile unsigned long *)PPC44x_EMAC0_MR0 = 0x20000000; + *(volatile unsigned long *)PPC4xx_EMAC0_MR0 = 0x20000000; __asm__ __volatile__("eieio"); #endif @@ -164,7 +172,9 @@ decompress_kernel(unsigned long load_addr, int num_words, unsigned long cksum) puts(" "); puthex((unsigned long)(&__ramdisk_end));puts("\n"); } +#ifndef CONFIG_40x /* don't overwrite the 40x image located at 0x00400000! */ avail_ram = (char *)0x00400000; +#endif end_avail = (char *)0x00800000; puts("avail ram: "); puthex((unsigned long)avail_ram); puts(" "); puthex((unsigned long)end_avail); puts("\n"); diff --git a/arch/ppc/boot/simple/openbios.c b/arch/ppc/boot/simple/openbios.c index c732b6d..81f11d8 100644 --- a/arch/ppc/boot/simple/openbios.c +++ b/arch/ppc/boot/simple/openbios.c @@ -1,19 +1,43 @@ /* * arch/ppc/boot/simple/openbios.c * - * 2005 (c) SYSGO AG - g.jaeger@sysgo.com + * Copyright (c) 2005 DENX Software Engineering + * Stefan Roese <sr@denx.de> + * + * Based on original work by + * 2005 (c) SYSGO AG - g.jaeger@sysgo.com + * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without * any warranty of any kind, whether express or implied. * - * Derived from arch/ppc/boot/simple/pibs.c (from MontaVista) */ #include <linux/types.h> #include <linux/config.h> #include <linux/string.h> #include <asm/ppcboot.h> -#include <platforms/4xx/ebony.h> +#include <asm/ibm4xx.h> +#include <asm/reg.h> +#ifdef CONFIG_40x +#include <asm/io.h> +#endif + +#if defined(CONFIG_BUBINGA) +#define BOARD_INFO_VECTOR 0xFFF80B50 /* openbios 1.19 moved this vector down - armin */ +#else +#define BOARD_INFO_VECTOR 0xFFFE0B50 +#endif + +#ifdef CONFIG_40x +/* Supply a default Ethernet address for those eval boards that don't + * ship with one. This is an address from the MBX board I have, so + * it is unlikely you will find it on your network. + */ +static ushort def_enet_addr[] = { 0x0800, 0x3e26, 0x1559 }; + +extern unsigned long timebase_period_ns; +#endif /* CONFIG_40x */ extern unsigned long decompress_kernel(unsigned long load_addr, int num_words, unsigned long cksum); @@ -23,15 +47,85 @@ extern unsigned long decompress_kernel(unsigned long load_addr, int num_words, bd_t hold_resid_buf __attribute__ ((__section__ (".data.boot"))); bd_t *hold_residual = &hold_resid_buf; +typedef struct openbios_board_info { + unsigned char bi_s_version[4]; /* Version of this structure */ + unsigned char bi_r_version[30]; /* Version of the IBM ROM */ + unsigned int bi_memsize; /* DRAM installed, in bytes */ +#ifdef CONFIG_405EP + unsigned char bi_enetaddr[2][6]; /* Local Ethernet MAC address */ +#else /* CONFIG_405EP */ + unsigned char bi_enetaddr[6]; /* Local Ethernet MAC address */ +#endif /* CONFIG_405EP */ + unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */ + unsigned int bi_intfreq; /* Processor speed, in Hz */ + unsigned int bi_busfreq; /* PLB Bus speed, in Hz */ + unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */ +#ifdef CONFIG_405EP + unsigned int bi_opb_busfreq; /* OPB Bus speed, in Hz */ + unsigned int bi_pllouta_freq; /* PLL OUTA speed, in Hz */ +#endif /* CONFIG_405EP */ +} openbios_bd_t; + void * load_kernel(unsigned long load_addr, int num_words, unsigned long cksum, void *ign1, void *ign2) { - decompress_kernel(load_addr, num_words, cksum); +#ifdef CONFIG_40x + openbios_bd_t *openbios_bd = NULL; + openbios_bd_t *(*get_board_info)(void) = + (openbios_bd_t *(*)(void))(*(unsigned long *)BOARD_INFO_VECTOR); + + /* + * On 40x platforms we not only need the MAC-addresses, but also the + * clocks and memsize. Now try to get all values using the OpenBIOS + * "get_board_info()" callback. + */ + if ((openbios_bd = get_board_info()) != NULL) { + /* + * Copy bd_info from OpenBIOS struct into U-Boot struct + * used by kernel + */ + hold_residual->bi_memsize = openbios_bd->bi_memsize; + hold_residual->bi_intfreq = openbios_bd->bi_intfreq; + hold_residual->bi_busfreq = openbios_bd->bi_busfreq; + hold_residual->bi_pci_busfreq = openbios_bd->bi_pci_busfreq; + memcpy(hold_residual->bi_pci_enetaddr, openbios_bd->bi_pci_enetaddr, 6); +#ifdef CONFIG_405EP + memcpy(hold_residual->bi_enetaddr, openbios_bd->bi_enetaddr[0], 6); + memcpy(hold_residual->bi_enet1addr, openbios_bd->bi_enetaddr[1], 6); + hold_residual->bi_opbfreq = openbios_bd->bi_opb_busfreq; + hold_residual->bi_procfreq = openbios_bd->bi_pllouta_freq; +#else /* CONFIG_405EP */ + memcpy(hold_residual->bi_enetaddr, openbios_bd->bi_enetaddr, 6); +#endif /* CONFIG_405EP */ + } else { + /* Hmmm...better try to stuff some defaults. + */ + hold_residual->bi_memsize = 16 * 1024 * 1024; + hold_residual->bi_intfreq = 200000000; + hold_residual->bi_busfreq = 100000000; + hold_residual->bi_pci_busfreq = 66666666; + + /* + * Only supply one mac-address in this fallback + */ + memcpy(hold_residual->bi_enetaddr, (void *)def_enet_addr, 6); +#ifdef CONFIG_405EP + hold_residual->bi_opbfreq = 50000000; + hold_residual->bi_procfreq = 200000000; +#endif /* CONFIG_405EP */ + } + timebase_period_ns = 1000000000 / hold_residual->bi_intfreq; +#endif /* CONFIG_40x */ + +#ifdef CONFIG_440GP /* simply copy the MAC addresses */ - memcpy(hold_residual->bi_enetaddr, (char *)EBONY_OPENBIOS_MAC_BASE, 6); - memcpy(hold_residual->bi_enet1addr, (char *)(EBONY_OPENBIOS_MAC_BASE+EBONY_OPENBIOS_MAC_OFFSET), 6); + memcpy(hold_residual->bi_enetaddr, (char *)OPENBIOS_MAC_BASE, 6); + memcpy(hold_residual->bi_enet1addr, (char *)(OPENBIOS_MAC_BASE+OPENBIOS_MAC_OFFSET), 6); +#endif /* CONFIG_440GP */ + + decompress_kernel(load_addr, num_words, cksum); return (void *)hold_residual; } diff --git a/arch/ppc/configs/ev64360_defconfig b/arch/ppc/configs/ev64360_defconfig index de9bbb7..d471e57 100644 --- a/arch/ppc/configs/ev64360_defconfig +++ b/arch/ppc/configs/ev64360_defconfig @@ -1,17 +1,17 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.13-rc5 -# Fri Aug 5 15:18:23 2005 +# Linux kernel version: 2.6.14 +# Fri Oct 28 19:15:34 2005 # CONFIG_MMU=y CONFIG_GENERIC_HARDIRQS=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_HAVE_DEC_LOCK=y CONFIG_PPC=y CONFIG_PPC32=y CONFIG_GENERIC_NVRAM=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y # # Code maturity level options @@ -26,6 +26,7 @@ CONFIG_INIT_ENV_ARG_LIMIT=32 # General setup # CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y @@ -35,6 +36,7 @@ CONFIG_SYSCTL=y CONFIG_HOTPLUG=y CONFIG_KOBJECT_UEVENT=y # CONFIG_IKCONFIG is not set +CONFIG_INITRAMFS_SOURCE="" # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set @@ -74,7 +76,7 @@ CONFIG_TAU=y # CONFIG_TAU_AVERAGE is not set # CONFIG_KEXEC is not set # CONFIG_CPU_FREQ is not set -# CONFIG_PM is not set +# CONFIG_WANT_EARLY_SERIAL is not set CONFIG_PPC_STD_MMU=y CONFIG_NOT_COHERENT_CACHE=y @@ -86,22 +88,18 @@ CONFIG_NOT_COHERENT_CACHE=y # CONFIG_KATANA is not set # CONFIG_WILLOW is not set # CONFIG_CPCI690 is not set -# CONFIG_PCORE is not set # CONFIG_POWERPMC250 is not set # CONFIG_CHESTNUT is not set # CONFIG_SPRUCE is not set # CONFIG_HDPU is not set # CONFIG_EV64260 is not set # CONFIG_LOPEC is not set -# CONFIG_MCPN765 is not set # CONFIG_MVME5100 is not set # CONFIG_PPLUS is not set # CONFIG_PRPMC750 is not set # CONFIG_PRPMC800 is not set # CONFIG_SANDPOINT is not set # CONFIG_RADSTONE_PPC7D is not set -# CONFIG_ADIR is not set -# CONFIG_K2 is not set # CONFIG_PAL4 is not set # CONFIG_GEMINI is not set # CONFIG_EST8260 is not set @@ -138,10 +136,13 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_CMDLINE_BOOL=y CONFIG_CMDLINE="console=ttyMM0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2" +# CONFIG_PM is not set +# CONFIG_SOFTWARE_SUSPEND is not set CONFIG_SECCOMP=y CONFIG_ISA_DMA_API=y @@ -152,7 +153,6 @@ CONFIG_GENERIC_ISA_DMA=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y # CONFIG_PCI_LEGACY_PROC is not set -# CONFIG_PCI_NAMES is not set # # PCCARD (PCMCIA/CardBus) support @@ -206,14 +206,19 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_TUNNEL is not set -CONFIG_IP_TCPDIAG=y -# CONFIG_IP_TCPDIAG_IPV6 is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # CONFIG_IPV6 is not set # CONFIG_NETFILTER is not set # +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set @@ -239,6 +244,7 @@ CONFIG_TCP_CONG_BIC=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set +# CONFIG_IEEE80211 is not set # # Device Drivers @@ -252,6 +258,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# # Memory Technology Devices (MTD) # CONFIG_MTD=y @@ -358,7 +369,6 @@ CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" # CONFIG_LBD is not set # CONFIG_CDROM_PKTCDVD is not set @@ -379,6 +389,7 @@ CONFIG_IOSCHED_CFQ=y # # SCSI device support # +# CONFIG_RAID_ATTRS is not set # CONFIG_SCSI is not set # @@ -420,6 +431,10 @@ CONFIG_NETDEVICES=y # CONFIG_ARCNET is not set # +# PHY device support +# + +# # Ethernet (10 or 100Mbit) # # CONFIG_NET_ETHERNET is not set @@ -434,6 +449,7 @@ CONFIG_NETDEVICES=y # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set # CONFIG_R8169 is not set +# CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_TIGON3 is not set @@ -446,6 +462,7 @@ CONFIG_MV643XX_ETH_0=y # # Ethernet (10000 Mbit) # +# CONFIG_CHELSIO_T1 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set @@ -547,7 +564,20 @@ CONFIG_LEGACY_PTY_COUNT=256 # # Watchdog Cards # -# CONFIG_WATCHDOG is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_MV64X60_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set @@ -571,7 +601,6 @@ CONFIG_GEN_RTC=y # I2C support # # CONFIG_I2C is not set -# CONFIG_I2C_SENSOR is not set # # Dallas's 1-wire bus @@ -582,6 +611,7 @@ CONFIG_GEN_RTC=y # Hardware Monitoring support # CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set # CONFIG_HWMON_DEBUG_CHIP is not set # @@ -589,6 +619,10 @@ CONFIG_HWMON=y # # +# Multimedia Capabilities Port drivers +# + +# # Multimedia devices # # CONFIG_VIDEO_DEV is not set @@ -651,10 +685,6 @@ CONFIG_EXT2_FS=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set - -# -# XFS support -# # CONFIG_XFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set @@ -663,6 +693,7 @@ CONFIG_INOTIFY=y CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems @@ -683,11 +714,10 @@ CONFIG_DNOTIFY=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y -# CONFIG_DEVPTS_FS_XATTR is not set CONFIG_TMPFS=y -# CONFIG_TMPFS_XATTR is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y +# CONFIG_RELAYFS_FS is not set # # Miscellaneous filesystems @@ -735,6 +765,7 @@ CONFIG_SUNRPC=y # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set # # Partition Types @@ -751,6 +782,7 @@ CONFIG_MSDOS_PARTITION=y # Library routines # # CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y @@ -767,6 +799,7 @@ CONFIG_ZLIB_DEFLATE=y # CONFIG_PRINTK_TIME is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_SERIAL_TEXT_DEBUG is not set # # Security options diff --git a/arch/ppc/configs/stx_gp3_defconfig b/arch/ppc/configs/stx_gp3_defconfig index 66dae83..3fedc43 100644 --- a/arch/ppc/configs/stx_gp3_defconfig +++ b/arch/ppc/configs/stx_gp3_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.11-rc2 -# Wed Jan 26 14:32:58 2005 +# Linux kernel version: 2.6.12-rc4 +# Tue May 24 18:11:04 2005 # CONFIG_MMU=y CONFIG_GENERIC_HARDIRQS=y @@ -11,6 +11,7 @@ CONFIG_HAVE_DEC_LOCK=y CONFIG_PPC=y CONFIG_PPC32=y CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # # Code maturity level options @@ -18,6 +19,7 @@ CONFIG_GENERIC_NVRAM=y CONFIG_EXPERIMENTAL=y CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup @@ -29,7 +31,6 @@ CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set -CONFIG_LOG_BUF_SHIFT=14 CONFIG_HOTPLUG=y CONFIG_KOBJECT_UEVENT=y # CONFIG_IKCONFIG is not set @@ -37,6 +38,9 @@ CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set @@ -46,6 +50,7 @@ CONFIG_CC_ALIGN_LABELS=0 CONFIG_CC_ALIGN_LOOPS=0 CONFIG_CC_ALIGN_JUMPS=0 # CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 # # Loadable module support @@ -69,9 +74,11 @@ CONFIG_KMOD=y CONFIG_E500=y CONFIG_BOOKE=y CONFIG_FSL_BOOKE=y +# CONFIG_PHYS_64BIT is not set # CONFIG_SPE is not set CONFIG_MATH_EMULATION=y # CONFIG_CPU_FREQ is not set +# CONFIG_PM is not set CONFIG_85xx=y CONFIG_PPC_INDIRECT_PCI_BE=y @@ -96,6 +103,7 @@ CONFIG_HIGHMEM=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m # CONFIG_CMDLINE_BOOL is not set +CONFIG_ISA_DMA_API=y # # Bus options @@ -104,15 +112,15 @@ CONFIG_PCI=y CONFIG_PCI_DOMAINS=y # CONFIG_PCI_LEGACY_PROC is not set # CONFIG_PCI_NAMES is not set +# CONFIG_PCI_DEBUG is not set # # PCCARD (PCMCIA/CardBus) support # # CONFIG_PCCARD is not set - -# -# PC-card bridges -# +CONFIG_RAPIDIO=y +CONFIG_RAPIDIO_8_BIT_TRANSPORT=y +CONFIG_RAPIDIO_DISC_TIMEOUT=30 # # Advanced setup @@ -152,7 +160,7 @@ CONFIG_PARPORT=m CONFIG_PARPORT_PC=m # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set -# CONFIG_PARPORT_OTHER is not set +# CONFIG_PARPORT_GSC is not set # CONFIG_PARPORT_1284 is not set # @@ -264,7 +272,6 @@ CONFIG_SCSI_CONSTANTS=y # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set -# CONFIG_SCSI_EATA_PIO is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_IPS is not set @@ -274,7 +281,6 @@ CONFIG_SCSI_CONSTANTS=y # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set -# CONFIG_SCSI_QLOGIC_ISP is not set # CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set CONFIG_SCSI_QLA2XXX=m @@ -283,6 +289,7 @@ CONFIG_SCSI_QLA2XXX=m # CONFIG_SCSI_QLA2300 is not set # CONFIG_SCSI_QLA2322 is not set # CONFIG_SCSI_QLA6312 is not set +# CONFIG_SCSI_LPFC is not set # CONFIG_SCSI_DC395x is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set @@ -322,7 +329,6 @@ CONFIG_NET=y # CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set -# CONFIG_NETLINK_DEV is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y @@ -431,7 +437,7 @@ CONFIG_IP_NF_NAT_FTP=m # # Network testing # -# CONFIG_NET_PKTGEN is not set +CONFIG_NET_PKTGEN=y # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_HAMRADIO is not set @@ -499,6 +505,7 @@ CONFIG_GFAR_NAPI=y # Wan interfaces # # CONFIG_WAN is not set +CONFIG_RIONET=y # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PLIP is not set @@ -536,20 +543,6 @@ CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set # -# Input I/O drivers -# -# CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y -CONFIG_SERIO=y -CONFIG_SERIO_I8042=y -CONFIG_SERIO_SERPORT=y -# CONFIG_SERIO_CT82C710 is not set -# CONFIG_SERIO_PARKBD is not set -# CONFIG_SERIO_PCIPS2 is not set -CONFIG_SERIO_LIBPS2=y -# CONFIG_SERIO_RAW is not set - -# # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y @@ -567,6 +560,19 @@ CONFIG_MOUSE_PS2=y # CONFIG_INPUT_MISC is not set # +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_I8042=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_PARKBD is not set +# CONFIG_SERIO_PCIPS2 is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set +CONFIG_SOUND_GAMEPORT=y + +# # Character devices # # CONFIG_VT is not set @@ -590,6 +596,7 @@ CONFIG_SERIAL_CPM_SCC2=y # CONFIG_SERIAL_CPM_SCC4 is not set # CONFIG_SERIAL_CPM_SMC1 is not set # CONFIG_SERIAL_CPM_SMC2 is not set +# CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -626,6 +633,11 @@ CONFIG_DRM=m # CONFIG_RAW_DRIVER is not set # +# TPM devices +# +# CONFIG_TCG_TPM is not set + +# # I2C support # CONFIG_I2C=m @@ -648,12 +660,12 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set # CONFIG_I2C_I810 is not set +# CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_ISA is not set # CONFIG_I2C_MPC is not set # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_PARPORT is not set # CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_SCx200_ACB is not set @@ -677,7 +689,9 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_SENSORS_ASB100 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set # CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_LM63 is not set # CONFIG_SENSORS_LM75 is not set @@ -688,9 +702,11 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_SENSORS_LM85 is not set # CONFIG_SENSORS_LM87 is not set # CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_SIS5595 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_W83781D is not set @@ -700,10 +716,12 @@ CONFIG_I2C_ALGOBIT=m # # Other I2C Chip support # +# CONFIG_SENSORS_DS1337 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_RTC8564 is not set +# CONFIG_SENSORS_M41T00 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set @@ -732,7 +750,6 @@ CONFIG_I2C_ALGOBIT=m # Graphics support # # CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound @@ -752,13 +769,9 @@ CONFIG_SOUND=m # # USB support # -# CONFIG_USB is not set CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information -# +# CONFIG_USB is not set # # USB Gadget Support @@ -789,6 +802,10 @@ CONFIG_JBD_DEBUG=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set + +# +# XFS support +# # CONFIG_XFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set @@ -859,7 +876,6 @@ CONFIG_NFS_V3=y CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y -# CONFIG_EXPORTFS is not set CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set @@ -942,8 +958,10 @@ CONFIG_ZLIB_INFLATE=m # # Kernel hacking # +# CONFIG_PRINTK_TIME is not set CONFIG_DEBUG_KERNEL=y # CONFIG_MAGIC_SYSRQ is not set +CONFIG_LOG_BUF_SHIFT=14 # CONFIG_SCHEDSTATS is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_SPINLOCK is not set diff --git a/arch/ppc/kernel/Makefile b/arch/ppc/kernel/Makefile index c610ca9..76a55a4 100644 --- a/arch/ppc/kernel/Makefile +++ b/arch/ppc/kernel/Makefile @@ -22,6 +22,7 @@ obj-$(CONFIG_POWER4) += cpu_setup_power4.o obj-$(CONFIG_MODULES) += module.o ppc_ksyms.o obj-$(CONFIG_NOT_COHERENT_CACHE) += dma-mapping.o obj-$(CONFIG_PCI) += pci.o +obj-$(CONFIG_RAPIDIO) += rio.o obj-$(CONFIG_KGDB) += ppc-stub.o obj-$(CONFIG_SMP) += smp.o smp-tbsync.o obj-$(CONFIG_TAU) += temp.o diff --git a/arch/ppc/kernel/head_44x.S b/arch/ppc/kernel/head_44x.S index 8b49679..677c571 100644 --- a/arch/ppc/kernel/head_44x.S +++ b/arch/ppc/kernel/head_44x.S @@ -190,8 +190,8 @@ skpinv: addi r4,r4,1 /* Increment */ /* xlat fields */ lis r4,UART0_PHYS_IO_BASE@h /* RPN depends on SoC */ -#ifndef CONFIG_440EP - ori r4,r4,0x0001 /* ERPN is 1 for second 4GB page */ +#ifdef UART0_PHYS_ERPN + ori r4,r4,UART0_PHYS_ERPN /* Add ERPN if above 4GB */ #endif /* attrib fields */ diff --git a/arch/ppc/kernel/rio.c b/arch/ppc/kernel/rio.c new file mode 100644 index 0000000..29487fe --- /dev/null +++ b/arch/ppc/kernel/rio.c @@ -0,0 +1,52 @@ +/* + * RapidIO PPC32 support + * + * Copyright 2005 MontaVista Software, Inc. + * Matt Porter <mporter@kernel.crashing.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/rio.h> + +#include <asm/rio.h> + +/** + * platform_rio_init - Do platform specific RIO init + * + * Any platform specific initialization of RapdIO + * hardware is done here as well as registration + * of any active master ports in the system. + */ +void __attribute__ ((weak)) + platform_rio_init(void) +{ + printk(KERN_WARNING "RIO: No platform_rio_init() present\n"); +} + +/** + * ppc_rio_init - Do PPC32 RIO init + * + * Calls platform-specific RIO init code and then calls + * rio_init_mports() to initialize any master ports that + * have been registered with the RIO subsystem. + */ +static int __init ppc_rio_init(void) +{ + printk(KERN_INFO "RIO: RapidIO init\n"); + + /* Platform specific initialization */ + platform_rio_init(); + + /* Enumerate all registered ports */ + rio_init_mports(); + + return 0; +} + +subsys_initcall(ppc_rio_init); diff --git a/arch/ppc/platforms/4xx/Kconfig b/arch/ppc/platforms/4xx/Kconfig index 76f4476..d883791 100644 --- a/arch/ppc/platforms/4xx/Kconfig +++ b/arch/ppc/platforms/4xx/Kconfig @@ -82,6 +82,12 @@ config LUAN help This option enables support for the IBM PPC440SP evaluation board. +config YUCCA + bool "Yucca" + select WANT_EARLY_SERIAL + help + This option enables support for the AMCC PPC440SPe evaluation board. + config OCOTEA bool "Ocotea" select WANT_EARLY_SERIAL @@ -124,9 +130,14 @@ config 440SP depends on LUAN default y +config 440SPE + bool + depends on YUCCA + default y + config 440 bool - depends on 440GP || 440SP || 440EP + depends on 440GP || 440SP || 440SPE || 440EP default y config 440A @@ -158,7 +169,7 @@ config BOOKE config IBM_OCP bool - depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT + depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT default y config XILINX_OCP @@ -168,7 +179,7 @@ config XILINX_OCP config IBM_EMAC4 bool - depends on 440GX || 440SP + depends on 440GX || 440SP || 440SPE default y config BIOS_FIXUP @@ -214,7 +225,7 @@ config EMBEDDEDBOOT config IBM_OPENBIOS bool - depends on ASH || BUBINGA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT + depends on ASH || REDWOOD_5 || REDWOOD_6 default y config PPC4xx_DMA diff --git a/arch/ppc/platforms/4xx/Makefile b/arch/ppc/platforms/4xx/Makefile index 1dd6d7f..c9bb611 100644 --- a/arch/ppc/platforms/4xx/Makefile +++ b/arch/ppc/platforms/4xx/Makefile @@ -7,6 +7,7 @@ obj-$(CONFIG_EBONY) += ebony.o obj-$(CONFIG_EP405) += ep405.o obj-$(CONFIG_BUBINGA) += bubinga.o obj-$(CONFIG_LUAN) += luan.o +obj-$(CONFIG_YUCCA) += yucca.o obj-$(CONFIG_OCOTEA) += ocotea.o obj-$(CONFIG_REDWOOD_5) += redwood5.o obj-$(CONFIG_REDWOOD_6) += redwood6.o @@ -22,6 +23,7 @@ obj-$(CONFIG_440EP) += ibm440ep.o obj-$(CONFIG_440GP) += ibm440gp.o obj-$(CONFIG_440GX) += ibm440gx.o obj-$(CONFIG_440SP) += ibm440sp.o +obj-$(CONFIG_440SPE) += ppc440spe.o obj-$(CONFIG_405EP) += ibm405ep.o obj-$(CONFIG_405GPR) += ibm405gpr.o obj-$(CONFIG_VIRTEX_II_PRO) += virtex-ii_pro.o diff --git a/arch/ppc/platforms/4xx/bubinga.c b/arch/ppc/platforms/4xx/bubinga.c index 3678abf..8110f55 100644 --- a/arch/ppc/platforms/4xx/bubinga.c +++ b/arch/ppc/platforms/4xx/bubinga.c @@ -89,7 +89,7 @@ bubinga_early_serial_map(void) * by 16. */ uart_div = (mfdcr(DCRN_CPC0_UCR_BASE) & DCRN_CPC0_UCR_U0DIV); - uart_clock = __res.bi_pllouta_freq / uart_div; + uart_clock = __res.bi_procfreq / uart_div; /* Setup serial port access */ memset(&port, 0, sizeof(port)); diff --git a/arch/ppc/platforms/4xx/bubinga.h b/arch/ppc/platforms/4xx/bubinga.h index b1df856..b5380cf 100644 --- a/arch/ppc/platforms/4xx/bubinga.h +++ b/arch/ppc/platforms/4xx/bubinga.h @@ -1,52 +1,34 @@ /* - * Support for IBM PPC 405EP evaluation board (Bubinga). + * arch/ppc/platforms/4xx/bubinga.h * - * Author: SAW (IBM), derived from walnut.h. - * Maintained by MontaVista Software <source@mvista.com> + * Bubinga board definitions + * + * Copyright (c) 2005 DENX Software Engineering + * Stefan Roese <sr@denx.de> + * + * Based on original work by + * SAW (IBM) + * 2003 (c) MontaVista Softare Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. * - * 2003 (c) MontaVista Softare Inc. This file is licensed under the - * terms of the GNU General Public License version 2. This program is - * licensed "as is" without any warranty of any kind, whether express - * or implied. */ #ifdef __KERNEL__ #ifndef __BUBINGA_H__ #define __BUBINGA_H__ -/* 405EP */ +#include <linux/config.h> #include <platforms/4xx/ibm405ep.h> - -#ifndef __ASSEMBLY__ -/* - * Data structure defining board information maintained by the boot - * ROM on IBM's evaluation board. An effort has been made to - * keep the field names consistent with the 8xx 'bd_t' board info - * structures. - */ - -typedef struct board_info { - unsigned char bi_s_version[4]; /* Version of this structure */ - unsigned char bi_r_version[30]; /* Version of the IBM ROM */ - unsigned int bi_memsize; /* DRAM installed, in bytes */ - unsigned char bi_enetaddr[2][6]; /* Local Ethernet MAC address */ unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */ - unsigned int bi_intfreq; /* Processor speed, in Hz */ - unsigned int bi_busfreq; /* PLB Bus speed, in Hz */ - unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */ - unsigned int bi_opb_busfreq; /* OPB Bus speed, in Hz */ - unsigned int bi_pllouta_freq; /* PLL OUTA speed, in Hz */ -} bd_t; - -/* Some 4xx parts use a different timebase frequency from the internal clock. -*/ -#define bi_tbfreq bi_intfreq - +#include <asm/ppcboot.h> /* Memory map for the Bubinga board. * Generic 4xx plus RTC. */ -extern void *bubinga_rtc_base; #define BUBINGA_RTC_PADDR ((uint)0xf0000000) #define BUBINGA_RTC_VADDR BUBINGA_RTC_PADDR #define BUBINGA_RTC_SIZE ((uint)8*1024) @@ -58,12 +40,18 @@ extern void *bubinga_rtc_base; * for typical configurations at various CPU speeds. * The base baud is calculated as (FWDA / EXT UART DIV / 16) */ -#define BASE_BAUD 0 +#define BASE_BAUD 0 -#define BUBINGA_FPGA_BASE 0xF0300000 +/* Flash */ +#define PPC40x_FPGA_BASE 0xF0300000 +#define PPC40x_FPGA_REG_OFFS 1 /* offset to flash map reg */ +#define PPC40x_FLASH_ONBD_N(x) (x & 0x02) +#define PPC40x_FLASH_SRAM_SEL(x) (x & 0x01) +#define PPC40x_FLASH_LOW 0xFFF00000 +#define PPC40x_FLASH_HIGH 0xFFF80000 +#define PPC40x_FLASH_SIZE 0x80000 -#define PPC4xx_MACHINE_NAME "IBM Bubinga" +#define PPC4xx_MACHINE_NAME "IBM Bubinga" -#endif /* !__ASSEMBLY__ */ #endif /* __BUBINGA_H__ */ #endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/ebony.h b/arch/ppc/platforms/4xx/ebony.h index d08faa4..b91ad42 100644 --- a/arch/ppc/platforms/4xx/ebony.h +++ b/arch/ppc/platforms/4xx/ebony.h @@ -24,8 +24,8 @@ #define PPC44x_EMAC0_MR0 0xE0000800 /* Where to find the MAC info */ -#define EBONY_OPENBIOS_MAC_BASE 0xfffffe0c -#define EBONY_OPENBIOS_MAC_OFFSET 0x0c +#define OPENBIOS_MAC_BASE 0xfffffe0c +#define OPENBIOS_MAC_OFFSET 0x0c /* Default clock rates for Rev. B and Rev. C silicon */ #define EBONY_440GP_RB_SYSCLK 33000000 diff --git a/arch/ppc/platforms/4xx/ppc440spe.c b/arch/ppc/platforms/4xx/ppc440spe.c new file mode 100644 index 0000000..6139a0b --- /dev/null +++ b/arch/ppc/platforms/4xx/ppc440spe.c @@ -0,0 +1,148 @@ +/* + * arch/ppc/platforms/4xx/ppc440spe.c + * + * PPC440SPe I/O descriptions + * + * Roland Dreier <rolandd@cisco.com> + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * + * Matt Porter <mporter@kernel.crashing.org> + * Copyright 2002-2005 MontaVista Software Inc. + * + * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> + * Copyright (c) 2003, 2004 Zultys Technologies + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include <linux/init.h> +#include <linux/module.h> +#include <platforms/4xx/ppc440spe.h> +#include <asm/ocp.h> +#include <asm/ppc4xx_pic.h> + +static struct ocp_func_emac_data ppc440spe_emac0_def = { + .rgmii_idx = -1, /* No RGMII */ + .rgmii_mux = -1, /* No RGMII */ + .zmii_idx = -1, /* No ZMII */ + .zmii_mux = -1, /* No ZMII */ + .mal_idx = 0, /* MAL device index */ + .mal_rx_chan = 0, /* MAL rx channel number */ + .mal_tx_chan = 0, /* MAL tx channel number */ + .wol_irq = 61, /* WOL interrupt number */ + .mdio_idx = -1, /* No shared MDIO */ + .tah_idx = -1, /* No TAH */ +}; +OCP_SYSFS_EMAC_DATA() + +static struct ocp_func_mal_data ppc440spe_mal0_def = { + .num_tx_chans = 1, /* Number of TX channels */ + .num_rx_chans = 1, /* Number of RX channels */ + .txeob_irq = 38, /* TX End Of Buffer IRQ */ + .rxeob_irq = 39, /* RX End Of Buffer IRQ */ + .txde_irq = 34, /* TX Descriptor Error IRQ */ + .rxde_irq = 35, /* RX Descriptor Error IRQ */ + .serr_irq = 33, /* MAL System Error IRQ */ + .dcr_base = DCRN_MAL_BASE /* MAL0_CFG DCR number */ +}; +OCP_SYSFS_MAL_DATA() + +static struct ocp_func_iic_data ppc440spe_iic0_def = { + .fast_mode = 0, /* Use standad mode (100Khz) */ +}; + +static struct ocp_func_iic_data ppc440spe_iic1_def = { + .fast_mode = 0, /* Use standad mode (100Khz) */ +}; +OCP_SYSFS_IIC_DATA() + +struct ocp_def core_ocp[] = { + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_16550, + .index = 0, + .paddr = PPC440SPE_UART0_ADDR, + .irq = UART0_INT, + .pm = IBM_CPM_UART0, + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_16550, + .index = 1, + .paddr = PPC440SPE_UART1_ADDR, + .irq = UART1_INT, + .pm = IBM_CPM_UART1, + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_16550, + .index = 2, + .paddr = PPC440SPE_UART2_ADDR, + .irq = UART2_INT, + .pm = IBM_CPM_UART2, + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_IIC, + .index = 0, + .paddr = 0x00000004f0000400ULL, + .irq = 2, + .pm = IBM_CPM_IIC0, + .additions = &ppc440spe_iic0_def, + .show = &ocp_show_iic_data + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_IIC, + .index = 1, + .paddr = 0x00000004f0000500ULL, + .irq = 3, + .pm = IBM_CPM_IIC1, + .additions = &ppc440spe_iic1_def, + .show = &ocp_show_iic_data + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_GPIO, + .index = 0, + .paddr = 0x00000004f0000700ULL, + .irq = OCP_IRQ_NA, + .pm = IBM_CPM_GPIO0, + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_MAL, + .paddr = OCP_PADDR_NA, + .irq = OCP_IRQ_NA, + .pm = OCP_CPM_NA, + .additions = &ppc440spe_mal0_def, + .show = &ocp_show_mal_data, + }, + { .vendor = OCP_VENDOR_IBM, + .function = OCP_FUNC_EMAC, + .index = 0, + .paddr = 0x00000004f0000800ULL, + .irq = 60, + .pm = OCP_CPM_NA, + .additions = &ppc440spe_emac0_def, + .show = &ocp_show_emac_data, + }, + { .vendor = OCP_VENDOR_INVALID + } +}; + +/* Polarity and triggering settings for internal interrupt sources */ +struct ppc4xx_uic_settings ppc4xx_core_uic_cfg[] __initdata = { + { .polarity = 0xffffffff, + .triggering = 0x010f0004, + .ext_irq_mask = 0x00000000, + }, + { .polarity = 0xffffffff, + .triggering = 0x001f8040, + .ext_irq_mask = 0x00007c30, /* IRQ6 - IRQ7, IRQ8 - IRQ12 */ + }, + { .polarity = 0xffffffff, + .triggering = 0x00000000, + .ext_irq_mask = 0x000000fc, /* IRQ0 - IRQ5 */ + }, + { .polarity = 0xffffffff, + .triggering = 0x00000000, + .ext_irq_mask = 0x00000000, + }, +}; diff --git a/arch/ppc/platforms/4xx/ppc440spe.h b/arch/ppc/platforms/4xx/ppc440spe.h new file mode 100644 index 0000000..2216846 --- /dev/null +++ b/arch/ppc/platforms/4xx/ppc440spe.h @@ -0,0 +1,66 @@ +/* + * arch/ppc/platforms/4xx/ibm440spe.h + * + * PPC440SPe definitions + * + * Roland Dreier <rolandd@cisco.com> + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * + * Matt Porter <mporter@kernel.crashing.org> + * Copyright 2004-2005 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifdef __KERNEL__ +#ifndef __PPC_PLATFORMS_PPC440SPE_H +#define __PPC_PLATFORMS_PPC440SPE_H + +#include <linux/config.h> + +#include <asm/ibm44x.h> + +/* UART */ +#define PPC440SPE_UART0_ADDR 0x00000004f0000200ULL +#define PPC440SPE_UART1_ADDR 0x00000004f0000300ULL +#define PPC440SPE_UART2_ADDR 0x00000004f0000600ULL +#define UART0_INT 0 +#define UART1_INT 1 +#define UART2_INT 37 + +/* Clock and Power Management */ +#define IBM_CPM_IIC0 0x80000000 /* IIC interface */ +#define IBM_CPM_IIC1 0x40000000 /* IIC interface */ +#define IBM_CPM_PCI 0x20000000 /* PCI bridge */ +#define IBM_CPM_CPU 0x02000000 /* processor core */ +#define IBM_CPM_DMA 0x01000000 /* DMA controller */ +#define IBM_CPM_BGO 0x00800000 /* PLB to OPB bus arbiter */ +#define IBM_CPM_BGI 0x00400000 /* OPB to PLB bridge */ +#define IBM_CPM_EBC 0x00200000 /* External Bux Controller */ +#define IBM_CPM_EBM 0x00100000 /* Ext Bus Master Interface */ +#define IBM_CPM_DMC 0x00080000 /* SDRAM peripheral controller */ +#define IBM_CPM_PLB 0x00040000 /* PLB bus arbiter */ +#define IBM_CPM_SRAM 0x00020000 /* SRAM memory controller */ +#define IBM_CPM_PPM 0x00002000 /* PLB Performance Monitor */ +#define IBM_CPM_UIC1 0x00001000 /* Universal Interrupt Controller */ +#define IBM_CPM_GPIO0 0x00000800 /* General Purpose IO (??) */ +#define IBM_CPM_GPT 0x00000400 /* General Purpose Timers */ +#define IBM_CPM_UART0 0x00000200 /* serial port 0 */ +#define IBM_CPM_UART1 0x00000100 /* serial port 1 */ +#define IBM_CPM_UART2 0x00000100 /* serial port 1 */ +#define IBM_CPM_UIC0 0x00000080 /* Universal Interrupt Controller */ +#define IBM_CPM_TMRCLK 0x00000040 /* CPU timers */ +#define IBM_CPM_EMAC0 0x00000020 /* EMAC 0 */ + +#define DFLT_IBM4xx_PM ~(IBM_CPM_UIC | IBM_CPM_UIC1 | IBM_CPM_CPU \ + | IBM_CPM_EBC | IBM_CPM_SRAM | IBM_CPM_BGO \ + | IBM_CPM_EBM | IBM_CPM_PLB | IBM_CPM_OPB \ + | IBM_CPM_TMRCLK | IBM_CPM_DMA | IBM_CPM_PCI \ + | IBM_CPM_TAHOE0 | IBM_CPM_TAHOE1 \ + | IBM_CPM_EMAC0 | IBM_CPM_EMAC1 \ + | IBM_CPM_EMAC2 | IBM_CPM_EMAC3 ) +#endif /* __PPC_PLATFORMS_PPC440SP_H */ +#endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/sycamore.c b/arch/ppc/platforms/4xx/sycamore.c index d8019ee..281b4a2 100644 --- a/arch/ppc/platforms/4xx/sycamore.c +++ b/arch/ppc/platforms/4xx/sycamore.c @@ -88,9 +88,6 @@ ppc405_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) void __init sycamore_setup_arch(void) { -#define SYCAMORE_PS2_BASE 0xF0100000 -#define SYCAMORE_FPGA_BASE 0xF0300000 - void *fpga_brdc; unsigned char fpga_brdc_data; void *fpga_enable; @@ -100,7 +97,7 @@ sycamore_setup_arch(void) ppc4xx_setup_arch(); - ibm_ocp_set_emac(0, 1); + ibm_ocp_set_emac(0, 0); kb_data = ioremap(SYCAMORE_PS2_BASE, 8); if (!kb_data) { @@ -111,7 +108,7 @@ sycamore_setup_arch(void) kb_cs = kb_data + 1; - fpga_status = ioremap(SYCAMORE_FPGA_BASE, 8); + fpga_status = ioremap(PPC40x_FPGA_BASE, 8); if (!fpga_status) { printk(KERN_CRIT "sycamore_setup_arch() fpga_status ioremap failed\n"); diff --git a/arch/ppc/platforms/4xx/sycamore.h b/arch/ppc/platforms/4xx/sycamore.h index 3e7b4e2..1cd6c82 100644 --- a/arch/ppc/platforms/4xx/sycamore.h +++ b/arch/ppc/platforms/4xx/sycamore.h @@ -1,67 +1,52 @@ /* * arch/ppc/platforms/4xx/sycamore.h * - * Macros, definitions, and data structures specific to the IBM PowerPC - * 405GPr "Sycamore" evaluation board. + * Sycamore board definitions * - * Author: Armin Kuster <akuster@mvista.com> + * Copyright (c) 2005 DENX Software Engineering + * Stefan Roese <sr@denx.de> + * + * Based on original work by + * Armin Kuster <akuster@mvista.com> + * 2000 (c) MontaVista, Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. * - * 2000 (c) MontaVista, Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. */ #ifdef __KERNEL__ #ifndef __ASM_SYCAMORE_H__ #define __ASM_SYCAMORE_H__ +#include <linux/config.h> #include <platforms/4xx/ibm405gpr.h> +#include <asm/ppcboot.h> -#ifndef __ASSEMBLY__ -/* - * Data structure defining board information maintained by the boot - * ROM on IBM's "Sycamore" evaluation board. An effort has been made to - * keep the field names consistent with the 8xx 'bd_t' board info - * structures. - */ - -typedef struct board_info { - unsigned char bi_s_version[4]; /* Version of this structure */ - unsigned char bi_r_version[30]; /* Version of the IBM ROM */ - unsigned int bi_memsize; /* DRAM installed, in bytes */ - unsigned char bi_enetaddr[6]; /* Local Ethernet MAC address */ - unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */ - unsigned int bi_intfreq; /* Processor speed, in Hz */ - unsigned int bi_busfreq; /* PLB Bus speed, in Hz */ - unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */ -} bd_t; - -/* Some 4xx parts use a different timebase frequency from the internal clock. -*/ -#define bi_tbfreq bi_intfreq - - -/* Memory map for the IBM "Sycamore" 405GP evaluation board. +/* Memory map for the IBM "Sycamore" 405GPr evaluation board. * Generic 4xx plus RTC. */ -extern void *sycamore_rtc_base; #define SYCAMORE_RTC_PADDR ((uint)0xf0000000) #define SYCAMORE_RTC_VADDR SYCAMORE_RTC_PADDR -#define SYCAMORE_RTC_SIZE ((uint)8*1024) +#define SYCAMORE_RTC_SIZE ((uint)8*1024) -#ifdef CONFIG_PPC405GP_INTERNAL_CLOCK -#define BASE_BAUD 201600 -#else #define BASE_BAUD 691200 -#endif -#define SYCAMORE_PS2_BASE 0xF0100000 -#define SYCAMORE_FPGA_BASE 0xF0300000 +#define SYCAMORE_PS2_BASE 0xF0100000 + +/* Flash */ +#define PPC40x_FPGA_BASE 0xF0300000 +#define PPC40x_FPGA_REG_OFFS 5 /* offset to flash map reg */ +#define PPC40x_FLASH_ONBD_N(x) (x & 0x02) +#define PPC40x_FLASH_SRAM_SEL(x) (x & 0x01) +#define PPC40x_FLASH_LOW 0xFFF00000 +#define PPC40x_FLASH_HIGH 0xFFF80000 +#define PPC40x_FLASH_SIZE 0x80000 #define PPC4xx_MACHINE_NAME "IBM Sycamore" -#endif /* !__ASSEMBLY__ */ #endif /* __ASM_SYCAMORE_H__ */ #endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/walnut.c b/arch/ppc/platforms/4xx/walnut.c index a33eda4..74cb331 100644 --- a/arch/ppc/platforms/4xx/walnut.c +++ b/arch/ppc/platforms/4xx/walnut.c @@ -90,7 +90,7 @@ walnut_setup_arch(void) kb_cs = kb_data + 1; - fpga_status = ioremap(WALNUT_FPGA_BASE, 8); + fpga_status = ioremap(PPC40x_FPGA_BASE, 8); if (!fpga_status) { printk(KERN_CRIT "walnut_setup_arch() fpga_status ioremap failed\n"); diff --git a/arch/ppc/platforms/4xx/walnut.h b/arch/ppc/platforms/4xx/walnut.h index 04cfbf3..dcf2691 100644 --- a/arch/ppc/platforms/4xx/walnut.h +++ b/arch/ppc/platforms/4xx/walnut.h @@ -1,72 +1,55 @@ /* * arch/ppc/platforms/4xx/walnut.h * - * Macros, definitions, and data structures specific to the IBM PowerPC - * 405GP "Walnut" evaluation board. + * Walnut board definitions * - * Authors: Grant Erickson <grant@lcse.umn.edu>, Frank Rowand - * <frank_rowand@mvista.com>, Debbie Chu <debbie_chu@mvista.com> or - * source@mvista.com + * Copyright (c) 2005 DENX Software Engineering + * Stefan Roese <sr@denx.de> * - * Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu> + * Based on original work by + * Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu> + * Frank Rowand <frank_rowand@mvista.com> + * Debbie Chu <debbie_chu@mvista.com> + * 2000 (c) MontaVista, Software, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. * - * 2000 (c) MontaVista, Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. */ #ifdef __KERNEL__ #ifndef __ASM_WALNUT_H__ #define __ASM_WALNUT_H__ -/* We have a 405GP core */ +#include <linux/config.h> #include <platforms/4xx/ibm405gp.h> - -#ifndef __ASSEMBLY__ -/* - * Data structure defining board information maintained by the boot - * ROM on IBM's "Walnut" evaluation board. An effort has been made to - * keep the field names consistent with the 8xx 'bd_t' board info - * structures. - */ - -typedef struct board_info { - unsigned char bi_s_version[4]; /* Version of this structure */ - unsigned char bi_r_version[30]; /* Version of the IBM ROM */ - unsigned int bi_memsize; /* DRAM installed, in bytes */ - unsigned char bi_enetaddr[6]; /* Local Ethernet MAC address */ - unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */ - unsigned int bi_intfreq; /* Processor speed, in Hz */ - unsigned int bi_busfreq; /* PLB Bus speed, in Hz */ - unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */ -} bd_t; - -/* Some 4xx parts use a different timebase frequency from the internal clock. -*/ -#define bi_tbfreq bi_intfreq - +#include <asm/ppcboot.h> /* Memory map for the IBM "Walnut" 405GP evaluation board. * Generic 4xx plus RTC. */ -extern void *walnut_rtc_base; #define WALNUT_RTC_PADDR ((uint)0xf0000000) #define WALNUT_RTC_VADDR WALNUT_RTC_PADDR #define WALNUT_RTC_SIZE ((uint)8*1024) -#ifdef CONFIG_PPC405GP_INTERNAL_CLOCK -#define BASE_BAUD 201600 -#else #define BASE_BAUD 691200 -#endif #define WALNUT_PS2_BASE 0xF0100000 -#define WALNUT_FPGA_BASE 0xF0300000 + +/* Flash */ +#define PPC40x_FPGA_BASE 0xF0300000 +#define PPC40x_FPGA_REG_OFFS 5 /* offset to flash map reg */ +#define PPC40x_FLASH_ONBD_N(x) (x & 0x02) +#define PPC40x_FLASH_SRAM_SEL(x) (x & 0x01) +#define PPC40x_FLASH_LOW 0xFFF00000 +#define PPC40x_FLASH_HIGH 0xFFF80000 +#define PPC40x_FLASH_SIZE 0x80000 +#define WALNUT_FPGA_BASE PPC40x_FPGA_BASE #define PPC4xx_MACHINE_NAME "IBM Walnut" -#endif /* !__ASSEMBLY__ */ #endif /* __ASM_WALNUT_H__ */ #endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/4xx/yucca.c b/arch/ppc/platforms/4xx/yucca.c new file mode 100644 index 0000000..e60f4bd --- /dev/null +++ b/arch/ppc/platforms/4xx/yucca.c @@ -0,0 +1,395 @@ +/* + * arch/ppc/platforms/4xx/yucca.c + * + * Yucca board specific routines + * + * Roland Dreier <rolandd@cisco.com> (based on luan.c by Matt Porter) + * + * Copyright 2004-2005 MontaVista Software Inc. + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/stddef.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/reboot.h> +#include <linux/pci.h> +#include <linux/kdev_t.h> +#include <linux/types.h> +#include <linux/major.h> +#include <linux/blkdev.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/ide.h> +#include <linux/initrd.h> +#include <linux/seq_file.h> +#include <linux/root_dev.h> +#include <linux/tty.h> +#include <linux/serial.h> +#include <linux/serial_core.h> + +#include <asm/system.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/dma.h> +#include <asm/io.h> +#include <asm/machdep.h> +#include <asm/ocp.h> +#include <asm/pci-bridge.h> +#include <asm/time.h> +#include <asm/todc.h> +#include <asm/bootinfo.h> +#include <asm/ppc4xx_pic.h> +#include <asm/ppcboot.h> + +#include <syslib/ibm44x_common.h> +#include <syslib/ibm440gx_common.h> +#include <syslib/ibm440sp_common.h> +#include <syslib/ppc440spe_pcie.h> + +extern bd_t __res; + +static struct ibm44x_clocks clocks __initdata; + +static void __init +yucca_calibrate_decr(void) +{ + unsigned int freq; + + if (mfspr(SPRN_CCR1) & CCR1_TCS) + freq = YUCCA_TMR_CLK; + else + freq = clocks.cpu; + + ibm44x_calibrate_decr(freq); +} + +static int +yucca_show_cpuinfo(struct seq_file *m) +{ + seq_printf(m, "vendor\t\t: AMCC\n"); + seq_printf(m, "machine\t\t: PPC440SPe EVB (Yucca)\n"); + + return 0; +} + +static enum { + HOSE_UNKNOWN, + HOSE_PCIX, + HOSE_PCIE0, + HOSE_PCIE1, + HOSE_PCIE2 +} hose_type[4]; + +static inline int +yucca_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) +{ + struct pci_controller *hose = pci_bus_to_hose(dev->bus->number); + + if (hose_type[hose->index] == HOSE_PCIX) { + static char pci_irq_table[][4] = + /* + * PCI IDSEL/INTPIN->INTLINE + * A B C D + */ + { + { 81, -1, -1, -1 }, /* IDSEL 1 - PCIX0 Slot 0 */ + }; + const long min_idsel = 1, max_idsel = 1, irqs_per_slot = 4; + return PCI_IRQ_TABLE_LOOKUP; + } else if (hose_type[hose->index] == HOSE_PCIE0) { + static char pci_irq_table[][4] = + /* + * PCI IDSEL/INTPIN->INTLINE + * A B C D + */ + { + { 96, 97, 98, 99 }, + }; + const long min_idsel = 1, max_idsel = 1, irqs_per_slot = 4; + return PCI_IRQ_TABLE_LOOKUP; + } else if (hose_type[hose->index] == HOSE_PCIE1) { + static char pci_irq_table[][4] = + /* + * PCI IDSEL/INTPIN->INTLINE + * A B C D + */ + { + { 100, 101, 102, 103 }, + }; + const long min_idsel = 1, max_idsel = 1, irqs_per_slot = 4; + return PCI_IRQ_TABLE_LOOKUP; + } else if (hose_type[hose->index] == HOSE_PCIE2) { + static char pci_irq_table[][4] = + /* + * PCI IDSEL/INTPIN->INTLINE + * A B C D + */ + { + { 104, 105, 106, 107 }, + }; + const long min_idsel = 1, max_idsel = 1, irqs_per_slot = 4; + return PCI_IRQ_TABLE_LOOKUP; + } + return -1; +} + +static void __init yucca_set_emacdata(void) +{ + struct ocp_def *def; + struct ocp_func_emac_data *emacdata; + + /* Set phy_map, phy_mode, and mac_addr for the EMAC */ + def = ocp_get_one_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC, 0); + emacdata = def->additions; + emacdata->phy_map = 0x00000001; /* Skip 0x00 */ + emacdata->phy_mode = PHY_MODE_GMII; + memcpy(emacdata->mac_addr, __res.bi_enetaddr, 6); +} + +static int __init yucca_pcie_card_present(int port) +{ + void __iomem *pcie_fpga_base; + u16 reg; + + pcie_fpga_base = ioremap64(YUCCA_FPGA_REG_BASE, YUCCA_FPGA_REG_SIZE); + reg = in_be16(pcie_fpga_base + FPGA_REG1C); + iounmap(pcie_fpga_base); + + switch(port) { + case 0: return !(reg & FPGA_REG1C_PE0_PRSNT); + case 1: return !(reg & FPGA_REG1C_PE1_PRSNT); + case 2: return !(reg & FPGA_REG1C_PE2_PRSNT); + default: return 0; + } +} + +/* + * For the given slot, set rootpoint mode, send power to the slot, + * turn on the green LED and turn off the yellow LED, enable the clock + * and turn off reset. + */ +static void __init yucca_setup_pcie_fpga_rootpoint(int port) +{ + void __iomem *pcie_reg_fpga_base; + u16 power, clock, green_led, yellow_led, reset_off, rootpoint, endpoint; + + pcie_reg_fpga_base = ioremap64(YUCCA_FPGA_REG_BASE, YUCCA_FPGA_REG_SIZE); + + switch(port) { + case 0: + rootpoint = FPGA_REG1C_PE0_ROOTPOINT; + endpoint = 0; + power = FPGA_REG1A_PE0_PWRON; + green_led = FPGA_REG1A_PE0_GLED; + clock = FPGA_REG1A_PE0_REFCLK_ENABLE; + yellow_led = FPGA_REG1A_PE0_YLED; + reset_off = FPGA_REG1C_PE0_PERST; + break; + case 1: + rootpoint = 0; + endpoint = FPGA_REG1C_PE1_ENDPOINT; + power = FPGA_REG1A_PE1_PWRON; + green_led = FPGA_REG1A_PE1_GLED; + clock = FPGA_REG1A_PE1_REFCLK_ENABLE; + yellow_led = FPGA_REG1A_PE1_YLED; + reset_off = FPGA_REG1C_PE1_PERST; + break; + case 2: + rootpoint = 0; + endpoint = FPGA_REG1C_PE2_ENDPOINT; + power = FPGA_REG1A_PE2_PWRON; + green_led = FPGA_REG1A_PE2_GLED; + clock = FPGA_REG1A_PE2_REFCLK_ENABLE; + yellow_led = FPGA_REG1A_PE2_YLED; + reset_off = FPGA_REG1C_PE2_PERST; + break; + + default: + return; + } + + out_be16(pcie_reg_fpga_base + FPGA_REG1A, + ~(power | clock | green_led) & + (yellow_led | in_be16(pcie_reg_fpga_base + FPGA_REG1A))); + out_be16(pcie_reg_fpga_base + FPGA_REG1C, + ~(endpoint | reset_off) & + (rootpoint | in_be16(pcie_reg_fpga_base + FPGA_REG1C))); + + /* + * Leave device in reset for a while after powering on the + * slot to give it a chance to initialize. + */ + mdelay(250); + + out_be16(pcie_reg_fpga_base + FPGA_REG1C, + reset_off | in_be16(pcie_reg_fpga_base + FPGA_REG1C)); + + iounmap(pcie_reg_fpga_base); +} + +static void __init +yucca_setup_hoses(void) +{ + struct pci_controller *hose; + char name[20]; + int i; + + if (0 && ppc440spe_init_pcie()) { + printk(KERN_WARNING "PPC440SPe PCI Express initialization failed\n"); + return; + } + + for (i = 0; i <= 2; ++i) { + if (!yucca_pcie_card_present(i)) + continue; + + printk(KERN_INFO "PCIE%d: card present\n", i); + yucca_setup_pcie_fpga_rootpoint(i); + if (ppc440spe_init_pcie_rootport(i)) { + printk(KERN_WARNING "PCIE%d: initialization failed\n", i); + continue; + } + + hose = pcibios_alloc_controller(); + if (!hose) + return; + + sprintf(name, "PCIE%d host bridge", i); + pci_init_resource(&hose->io_resource, + YUCCA_PCIX_LOWER_IO, + YUCCA_PCIX_UPPER_IO, + IORESOURCE_IO, + name); + + hose->mem_space.start = YUCCA_PCIE_LOWER_MEM + + i * YUCCA_PCIE_MEM_SIZE; + hose->mem_space.end = hose->mem_space.start + + YUCCA_PCIE_MEM_SIZE - 1; + + pci_init_resource(&hose->mem_resources[0], + hose->mem_space.start, + hose->mem_space.end, + IORESOURCE_MEM, + name); + + hose->first_busno = 0; + hose->last_busno = 15; + hose_type[hose->index] = HOSE_PCIE0 + i; + + ppc440spe_setup_pcie(hose, i); + hose->last_busno = pciauto_bus_scan(hose, hose->first_busno); + } + + ppc_md.pci_swizzle = common_swizzle; + ppc_md.pci_map_irq = yucca_map_irq; +} + +TODC_ALLOC(); + +static void __init +yucca_early_serial_map(void) +{ + struct uart_port port; + + /* Setup ioremapped serial port access */ + memset(&port, 0, sizeof(port)); + port.membase = ioremap64(PPC440SPE_UART0_ADDR, 8); + port.irq = UART0_INT; + port.uartclk = clocks.uart0; + port.regshift = 0; + port.iotype = SERIAL_IO_MEM; + port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.line = 0; + + if (early_serial_setup(&port) != 0) { + printk("Early serial init of port 0 failed\n"); + } + + port.membase = ioremap64(PPC440SPE_UART1_ADDR, 8); + port.irq = UART1_INT; + port.uartclk = clocks.uart1; + port.line = 1; + + if (early_serial_setup(&port) != 0) { + printk("Early serial init of port 1 failed\n"); + } + + port.membase = ioremap64(PPC440SPE_UART2_ADDR, 8); + port.irq = UART2_INT; + port.uartclk = BASE_BAUD; + port.line = 2; + + if (early_serial_setup(&port) != 0) { + printk("Early serial init of port 2 failed\n"); + } +} + +static void __init +yucca_setup_arch(void) +{ + yucca_set_emacdata(); + +#if !defined(CONFIG_BDI_SWITCH) + /* + * The Abatron BDI JTAG debugger does not tolerate others + * mucking with the debug registers. + */ + mtspr(SPRN_DBCR0, (DBCR0_TDE | DBCR0_IDM)); +#endif + + /* + * Determine various clocks. + * To be completely correct we should get SysClk + * from FPGA, because it can be changed by on-board switches + * --ebs + */ + /* 440GX and 440SPe clocking is the same - rd */ + ibm440gx_get_clocks(&clocks, 33333333, 6 * 1843200); + ocp_sys_info.opb_bus_freq = clocks.opb; + + /* init to some ~sane value until calibrate_delay() runs */ + loops_per_jiffy = 50000000/HZ; + + /* Setup PCIXn host bridges */ + yucca_setup_hoses(); + +#ifdef CONFIG_BLK_DEV_INITRD + if (initrd_start) + ROOT_DEV = Root_RAM0; + else +#endif +#ifdef CONFIG_ROOT_NFS + ROOT_DEV = Root_NFS; +#else + ROOT_DEV = Root_HDA1; +#endif + + yucca_early_serial_map(); + + /* Identify the system */ + printk("Yucca port (Roland Dreier <rolandd@cisco.com>)\n"); +} + +void __init platform_init(unsigned long r3, unsigned long r4, + unsigned long r5, unsigned long r6, unsigned long r7) +{ + ibm44x_platform_init(r3, r4, r5, r6, r7); + + ppc_md.setup_arch = yucca_setup_arch; + ppc_md.show_cpuinfo = yucca_show_cpuinfo; + ppc_md.find_end_of_memory = ibm440sp_find_end_of_memory; + ppc_md.get_irq = NULL; /* Set in ppc4xx_pic_init() */ + + ppc_md.calibrate_decr = yucca_calibrate_decr; +#ifdef CONFIG_KGDB + ppc_md.early_serial_map = yucca_early_serial_map; +#endif +} diff --git a/arch/ppc/platforms/4xx/yucca.h b/arch/ppc/platforms/4xx/yucca.h new file mode 100644 index 0000000..01a4afe --- /dev/null +++ b/arch/ppc/platforms/4xx/yucca.h @@ -0,0 +1,111 @@ +/* + * arch/ppc/platforms/4xx/yucca.h + * + * Yucca board definitions + * + * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter) + * + * Copyright 2004-2005 MontaVista Software Inc. + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifdef __KERNEL__ +#ifndef __ASM_YUCCA_H__ +#define __ASM_YUCCA_H__ + +#include <linux/config.h> +#include <platforms/4xx/ppc440spe.h> + +/* F/W TLB mapping used in bootloader glue to reset EMAC */ +#define PPC44x_EMAC0_MR0 0xa0000800 + +/* Location of MAC addresses in PIBS image */ +#define PIBS_FLASH_BASE 0xffe00000 +#define PIBS_MAC_BASE (PIBS_FLASH_BASE+0x1b0400) + +/* External timer clock frequency */ +#define YUCCA_TMR_CLK 25000000 + +/* + * FPGA registers + */ +#define YUCCA_FPGA_REG_BASE 0x00000004e2000000ULL +#define YUCCA_FPGA_REG_SIZE 0x24 + +#define FPGA_REG1A 0x1a + +#define FPGA_REG1A_PE0_GLED 0x8000 +#define FPGA_REG1A_PE1_GLED 0x4000 +#define FPGA_REG1A_PE2_GLED 0x2000 +#define FPGA_REG1A_PE0_YLED 0x1000 +#define FPGA_REG1A_PE1_YLED 0x0800 +#define FPGA_REG1A_PE2_YLED 0x0400 +#define FPGA_REG1A_PE0_PWRON 0x0200 +#define FPGA_REG1A_PE1_PWRON 0x0100 +#define FPGA_REG1A_PE2_PWRON 0x0080 +#define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040 +#define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020 +#define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010 +#define FPGA_REG1A_PE_SPREAD0 0x0008 +#define FPGA_REG1A_PE_SPREAD1 0x0004 +#define FPGA_REG1A_PE_SELSOURCE_0 0x0002 +#define FPGA_REG1A_PE_SELSOURCE_1 0x0001 + +#define FPGA_REG1C 0x1c + +#define FPGA_REG1C_PE0_ROOTPOINT 0x8000 +#define FPGA_REG1C_PE1_ENDPOINT 0x4000 +#define FPGA_REG1C_PE2_ENDPOINT 0x2000 +#define FPGA_REG1C_PE0_PRSNT 0x1000 +#define FPGA_REG1C_PE1_PRSNT 0x0800 +#define FPGA_REG1C_PE2_PRSNT 0x0400 +#define FPGA_REG1C_PE0_WAKE 0x0080 +#define FPGA_REG1C_PE1_WAKE 0x0040 +#define FPGA_REG1C_PE2_WAKE 0x0020 +#define FPGA_REG1C_PE0_PERST 0x0010 +#define FPGA_REG1C_PE1_PERST 0x0008 +#define FPGA_REG1C_PE2_PERST 0x0004 + +/* + * Serial port defines + */ +#define RS_TABLE_SIZE 3 + +/* PIBS defined UART mappings, used before early_serial_setup */ +#define UART0_IO_BASE 0xa0000200 +#define UART1_IO_BASE 0xa0000300 +#define UART2_IO_BASE 0xa0000600 + +#define BASE_BAUD 11059200 +#define STD_UART_OP(num) \ + { 0, BASE_BAUD, 0, UART##num##_INT, \ + (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ + iomem_base: (void*)UART##num##_IO_BASE, \ + io_type: SERIAL_IO_MEM}, + +#define SERIAL_PORT_DFNS \ + STD_UART_OP(0) \ + STD_UART_OP(1) \ + STD_UART_OP(2) + +/* PCI support */ +#define YUCCA_PCIX_LOWER_IO 0x00000000 +#define YUCCA_PCIX_UPPER_IO 0x0000ffff +#define YUCCA_PCIX_LOWER_MEM 0x80000000 +#define YUCCA_PCIX_UPPER_MEM 0x8fffffff +#define YUCCA_PCIE_LOWER_MEM 0x90000000 +#define YUCCA_PCIE_MEM_SIZE 0x10000000 + +#define YUCCA_PCIX_MEM_SIZE 0x10000000 +#define YUCCA_PCIX_MEM_OFFSET 0x00000000 +#define YUCCA_PCIE_MEM_SIZE 0x10000000 +#define YUCCA_PCIE_MEM_OFFSET 0x00000000 + +#endif /* __ASM_YUCCA_H__ */ +#endif /* __KERNEL__ */ diff --git a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c index bd3ac01..16ad092 100644 --- a/arch/ppc/platforms/85xx/mpc85xx_ads_common.c +++ b/arch/ppc/platforms/85xx/mpc85xx_ads_common.c @@ -45,6 +45,8 @@ #include <mm/mmu_decl.h> +#include <syslib/ppc85xx_rio.h> + #include <platforms/85xx/mpc85xx_ads_common.h> #ifndef CONFIG_PCI @@ -189,3 +191,11 @@ mpc85xx_exclude_device(u_char bus, u_char devfn) } #endif /* CONFIG_PCI */ + +#ifdef CONFIG_RAPIDIO +void platform_rio_init(void) +{ + /* 512MB RIO LAW at 0xc0000000 */ + mpc85xx_rio_setup(0xc0000000, 0x20000000); +} +#endif /* CONFIG_RAPIDIO */ diff --git a/arch/ppc/platforms/85xx/stx_gp3.c b/arch/ppc/platforms/85xx/stx_gp3.c index 1e1b85f..15ce9d0 100644 --- a/arch/ppc/platforms/85xx/stx_gp3.c +++ b/arch/ppc/platforms/85xx/stx_gp3.c @@ -37,6 +37,7 @@ #include <linux/module.h> #include <linux/fsl_devices.h> #include <linux/interrupt.h> +#include <linux/rio.h> #include <asm/system.h> #include <asm/pgtable.h> @@ -57,6 +58,7 @@ #include <syslib/cpm2_pic.h> #include <syslib/ppc85xx_common.h> +#include <syslib/ppc85xx_rio.h> unsigned char __res[sizeof(bd_t)]; @@ -273,6 +275,18 @@ int mpc85xx_exclude_device(u_char bus, u_char devfn) } #endif /* CONFIG_PCI */ +#ifdef CONFIG_RAPIDIO +void +platform_rio_init(void) +{ + /* + * The STx firmware configures the RapidIO Local Access Window + * at 0xc0000000 with a size of 512MB. + */ + mpc85xx_rio_setup(0xc0000000, 0x20000000); +} +#endif /* CONFIG_RAPIDIO */ + void __init platform_init(unsigned long r3, unsigned long r4, unsigned long r5, unsigned long r6, unsigned long r7) diff --git a/arch/ppc/platforms/ev64360.c b/arch/ppc/platforms/ev64360.c index b132456..b9d844f 100644 --- a/arch/ppc/platforms/ev64360.c +++ b/arch/ppc/platforms/ev64360.c @@ -52,6 +52,8 @@ static u32 ev64360_bus_frequency; unsigned char __res[sizeof(bd_t)]; +TODC_ALLOC(); + static int __init ev64360_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) { @@ -182,6 +184,9 @@ ev64360_setup_peripherals(void) EV64360_RTC_WINDOW_BASE, EV64360_RTC_WINDOW_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_1_WIN); + TODC_INIT(TODC_TYPE_DS1501, 0, 0, + ioremap(EV64360_RTC_WINDOW_BASE, EV64360_RTC_WINDOW_SIZE), 8); + mv64x60_set_32bit_window(&bh, MV64x60_CPU2SRAM_WIN, EV64360_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2SRAM_WIN); @@ -496,6 +501,13 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5, ppc_md.power_off = ev64360_power_off; ppc_md.halt = ev64360_halt; ppc_md.find_end_of_memory = ev64360_find_end_of_memory; + ppc_md.init = NULL; + + ppc_md.time_init = todc_time_init; + ppc_md.set_rtc_time = todc_set_rtc_time; + ppc_md.get_rtc_time = todc_get_rtc_time; + ppc_md.nvram_read_val = todc_direct_read_val; + ppc_md.nvram_write_val = todc_direct_write_val; ppc_md.calibrate_decr = ev64360_calibrate_decr; #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE) diff --git a/arch/ppc/syslib/Makefile b/arch/ppc/syslib/Makefile index b4ef15b..5bd33ba 100644 --- a/arch/ppc/syslib/Makefile +++ b/arch/ppc/syslib/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_440EP) += ibm440gx_common.o obj-$(CONFIG_440GP) += ibm440gp_common.o obj-$(CONFIG_440GX) += ibm440gx_common.o obj-$(CONFIG_440SP) += ibm440gx_common.o ibm440sp_common.o +obj-$(CONFIG_440SPE) += ibm440gx_common.o ibm440sp_common.o ppc440spe_pcie.o ifeq ($(CONFIG_4xx),y) ifeq ($(CONFIG_VIRTEX_II_PRO),y) obj-$(CONFIG_40x) += xilinx_pic.o @@ -32,6 +33,7 @@ obj-$(CONFIG_PPC4xx_DMA) += ppc4xx_dma.o obj-$(CONFIG_PPC4xx_EDMA) += ppc4xx_sgdma.o ifeq ($(CONFIG_40x),y) obj-$(CONFIG_PCI) += pci_auto.o ppc405_pci.o +obj-$(CONFIG_RAPIDIO) += ppc85xx_rio.o endif endif obj-$(CONFIG_8xx) += m8xx_setup.o ppc8xx_pic.o $(wdt-mpc8xx-y) \ @@ -46,12 +48,14 @@ obj-$(CONFIG_BAMBOO) += pci_auto.o todc_time.o obj-$(CONFIG_CPCI690) += todc_time.o pci_auto.o obj-$(CONFIG_EBONY) += pci_auto.o todc_time.o obj-$(CONFIG_EV64260) += todc_time.o pci_auto.o +obj-$(CONFIG_EV64360) += todc_time.o obj-$(CONFIG_CHESTNUT) += mv64360_pic.o pci_auto.o obj-$(CONFIG_GEMINI) += open_pic.o obj-$(CONFIG_GT64260) += gt64260_pic.o obj-$(CONFIG_LOPEC) += pci_auto.o todc_time.o obj-$(CONFIG_HDPU) += pci_auto.o obj-$(CONFIG_LUAN) += pci_auto.o todc_time.o +obj-$(CONFIG_YUCCA) += pci_auto.o todc_time.o obj-$(CONFIG_KATANA) += pci_auto.o obj-$(CONFIG_MV64360) += mv64360_pic.o obj-$(CONFIG_MV64X60) += mv64x60.o mv64x60_win.o diff --git a/arch/ppc/syslib/ibm440sp_common.c b/arch/ppc/syslib/ibm440sp_common.c index 417d4cf..cdafda1 100644 --- a/arch/ppc/syslib/ibm440sp_common.c +++ b/arch/ppc/syslib/ibm440sp_common.c @@ -1,7 +1,7 @@ /* * arch/ppc/syslib/ibm440sp_common.c * - * PPC440SP system library + * PPC440SP/PPC440SPe system library * * Matt Porter <mporter@kernel.crashing.org> * Copyright 2002-2005 MontaVista Software Inc. @@ -35,7 +35,7 @@ unsigned long __init ibm440sp_find_end_of_memory(void) u32 mem_size = 0; /* Read two bank sizes and sum */ - for (i=0; i<2; i++) + for (i=0; i< MQ0_NUM_BANKS; i++) switch (mfdcr(DCRN_MQ0_BS0BAS + i) & MQ0_CONFIG_SIZE_MASK) { case MQ0_CONFIG_SIZE_8M: mem_size += PPC44x_MEM_SIZE_8M; diff --git a/arch/ppc/syslib/ibm44x_common.c b/arch/ppc/syslib/ibm44x_common.c index 5152c8e..71db11d 100644 --- a/arch/ppc/syslib/ibm44x_common.c +++ b/arch/ppc/syslib/ibm44x_common.c @@ -20,6 +20,7 @@ #include <linux/types.h> #include <linux/serial.h> #include <linux/module.h> +#include <linux/initrd.h> #include <asm/ibm44x.h> #include <asm/mmu.h> @@ -214,9 +215,20 @@ void __init ibm44x_platform_init(unsigned long r3, unsigned long r4, unsigned lo /* Called from machine_check_exception */ void platform_machine_check(struct pt_regs *regs) { +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) + printk("PLB0: BEAR=0x%08x%08x ACR= 0x%08x BESR= 0x%08x%08x\n", + mfdcr(DCRN_PLB0_BEARH), mfdcr(DCRN_PLB0_BEARL), + mfdcr(DCRN_PLB0_ACR), mfdcr(DCRN_PLB0_BESRH), + mfdcr(DCRN_PLB0_BESRL)); + printk("PLB1: BEAR=0x%08x%08x ACR= 0x%08x BESR= 0x%08x%08x\n", + mfdcr(DCRN_PLB1_BEARH), mfdcr(DCRN_PLB1_BEARL), + mfdcr(DCRN_PLB1_ACR), mfdcr(DCRN_PLB1_BESRH), + mfdcr(DCRN_PLB1_BESRL)); +#else printk("PLB0: BEAR=0x%08x%08x ACR= 0x%08x BESR= 0x%08x\n", mfdcr(DCRN_PLB0_BEARH), mfdcr(DCRN_PLB0_BEARL), mfdcr(DCRN_PLB0_ACR), mfdcr(DCRN_PLB0_BESR)); +#endif printk("POB0: BEAR=0x%08x%08x BESR0=0x%08x BESR1=0x%08x\n", mfdcr(DCRN_POB0_BEARH), mfdcr(DCRN_POB0_BEARL), mfdcr(DCRN_POB0_BESR0), mfdcr(DCRN_POB0_BESR1)); diff --git a/arch/ppc/syslib/ppc405_pci.c b/arch/ppc/syslib/ppc405_pci.c index 81c83bf..d6d838b 100644 --- a/arch/ppc/syslib/ppc405_pci.c +++ b/arch/ppc/syslib/ppc405_pci.c @@ -89,13 +89,6 @@ ppc4xx_find_bridges(void) isa_mem_base = 0; pci_dram_offset = 0; -#if (PSR_PCI_ARBIT_EN > 1) - /* Check if running in slave mode */ - if ((mfdcr(DCRN_CHPSR) & PSR_PCI_ARBIT_EN) == 0) { - printk("Running as PCI slave, kernel PCI disabled !\n"); - return; - } -#endif /* Setup PCI32 hose */ hose_a = pcibios_alloc_controller(); if (!hose_a) diff --git a/arch/ppc/syslib/ppc440spe_pcie.c b/arch/ppc/syslib/ppc440spe_pcie.c new file mode 100644 index 0000000..1509fc1 --- /dev/null +++ b/arch/ppc/syslib/ppc440spe_pcie.c @@ -0,0 +1,442 @@ +/* + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * Roland Dreier <rolandd@cisco.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/init.h> + +#include <asm/reg.h> +#include <asm/io.h> +#include <asm/ibm44x.h> + +#include "ppc440spe_pcie.h" + +static int +pcie_read_config(struct pci_bus *bus, unsigned int devfn, int offset, + int len, u32 *val) +{ + struct pci_controller *hose = bus->sysdata; + + if (PCI_SLOT(devfn) != 1) + return PCIBIOS_DEVICE_NOT_FOUND; + + offset += devfn << 12; + + /* + * Note: the caller has already checked that offset is + * suitably aligned and that len is 1, 2 or 4. + */ + switch (len) { + case 1: + *val = in_8(hose->cfg_data + offset); + break; + case 2: + *val = in_le16(hose->cfg_data + offset); + break; + default: + *val = in_le32(hose->cfg_data + offset); + break; + } + + if (0) printk("%s: read %x(%d) @ %x\n", __func__, *val, len, offset); + + return PCIBIOS_SUCCESSFUL; +} + +static int +pcie_write_config(struct pci_bus *bus, unsigned int devfn, int offset, + int len, u32 val) +{ + struct pci_controller *hose = bus->sysdata; + + if (PCI_SLOT(devfn) != 1) + return PCIBIOS_DEVICE_NOT_FOUND; + + offset += devfn << 12; + + switch (len) { + case 1: + out_8(hose->cfg_data + offset, val); + break; + case 2: + out_le16(hose->cfg_data + offset, val); + break; + default: + out_le32(hose->cfg_data + offset, val); + break; + } + return PCIBIOS_SUCCESSFUL; +} + +static struct pci_ops pcie_pci_ops = +{ + .read = pcie_read_config, + .write = pcie_write_config +}; + +enum { + PTYPE_ENDPOINT = 0x0, + PTYPE_LEGACY_ENDPOINT = 0x1, + PTYPE_ROOT_PORT = 0x4, + + LNKW_X1 = 0x1, + LNKW_X4 = 0x4, + LNKW_X8 = 0x8 +}; + +static void check_error(void) +{ + u32 valPE0, valPE1, valPE2; + + /* SDR0_PEGPLLLCT1 reset */ + if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) { + printk(KERN_INFO "PCIE: SDR0_PEGPLLLCT1 reset error 0x%8x\n", valPE0); + } + + valPE0 = SDR_READ(PESDR0_RCSSET); + valPE1 = SDR_READ(PESDR1_RCSSET); + valPE2 = SDR_READ(PESDR2_RCSSET); + + /* SDR0_PExRCSSET rstgu */ + if ( !(valPE0 & 0x01000000) || + !(valPE1 & 0x01000000) || + !(valPE2 & 0x01000000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstgu error\n"); + } + + /* SDR0_PExRCSSET rstdl */ + if ( !(valPE0 & 0x00010000) || + !(valPE1 & 0x00010000) || + !(valPE2 & 0x00010000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstdl error\n"); + } + + /* SDR0_PExRCSSET rstpyn */ + if ( (valPE0 & 0x00001000) || + (valPE1 & 0x00001000) || + (valPE2 & 0x00001000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstpyn error\n"); + } + + /* SDR0_PExRCSSET hldplb */ + if ( (valPE0 & 0x10000000) || + (valPE1 & 0x10000000) || + (valPE2 & 0x10000000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET hldplb error\n"); + } + + /* SDR0_PExRCSSET rdy */ + if ( (valPE0 & 0x00100000) || + (valPE1 & 0x00100000) || + (valPE2 & 0x00100000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rdy error\n"); + } + + /* SDR0_PExRCSSET shutdown */ + if ( (valPE0 & 0x00000100) || + (valPE1 & 0x00000100) || + (valPE2 & 0x00000100)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET shutdown error\n"); + } +} + +/* + * Initialize PCI Express core as described in User Manual section 27.12.1 + */ +int ppc440spe_init_pcie(void) +{ + /* Set PLL clock receiver to LVPECL */ + SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) | 1 << 28); + + check_error(); + + printk(KERN_INFO "PCIE initialization OK\n"); + + if (!(SDR_READ(PESDR0_PLLLCT2) & 0x10000)) + printk(KERN_INFO "PESDR_PLLCT2 resistance calibration failed (0x%08x)\n", + SDR_READ(PESDR0_PLLLCT2)); + + /* De-assert reset of PCIe PLL, wait for lock */ + SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) & ~(1 << 24)); + udelay(3); + + return 0; +} + +int ppc440spe_init_pcie_rootport(int port) +{ + static int core_init; + void __iomem *utl_base; + u32 val = 0; + int i; + + if (!core_init) { + ++core_init; + i = ppc440spe_init_pcie(); + if (i) + return i; + } + + /* + * Initialize various parts of the PCI Express core for our port: + * + * - Set as a root port and enable max width + * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). + * - Set up UTL configuration. + * - Increase SERDES drive strength to levels suggested by AMCC. + * - De-assert RSTPYN, RSTDL and RSTGU. + */ + switch (port) { + case 0: + SDR_WRITE(PESDR0_DLPSET, PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12); + + SDR_WRITE(PESDR0_UTLSET1, 0x21222222); + SDR_WRITE(PESDR0_UTLSET2, 0x11000000); + + SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); + + SDR_WRITE(PESDR0_RCSSET, + (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 1: + SDR_WRITE(PESDR1_DLPSET, PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); + + SDR_WRITE(PESDR1_UTLSET1, 0x21222222); + SDR_WRITE(PESDR1_UTLSET2, 0x11000000); + + SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); + + SDR_WRITE(PESDR1_RCSSET, + (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 2: + SDR_WRITE(PESDR2_DLPSET, PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); + + SDR_WRITE(PESDR2_UTLSET1, 0x21222222); + SDR_WRITE(PESDR2_UTLSET2, 0x11000000); + + SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); + + SDR_WRITE(PESDR2_RCSSET, + (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + } + + mdelay(1000); + + switch (port) { + case 0: val = SDR_READ(PESDR0_RCSSTS); break; + case 1: val = SDR_READ(PESDR1_RCSSTS); break; + case 2: val = SDR_READ(PESDR2_RCSSTS); break; + } + + if (!(val & (1 << 20))) + printk(KERN_INFO "PCIE%d: PGRST inactive\n", port); + else + printk(KERN_WARNING "PGRST for PCIE%d failed %08x\n", port, val); + + switch (port) { + case 0: printk(KERN_INFO "PCIE0: LOOP %08x\n", SDR_READ(PESDR0_LOOP)); break; + case 1: printk(KERN_INFO "PCIE1: LOOP %08x\n", SDR_READ(PESDR1_LOOP)); break; + case 2: printk(KERN_INFO "PCIE2: LOOP %08x\n", SDR_READ(PESDR2_LOOP)); break; + } + + /* + * Map UTL registers at 0xc_1000_0n00 + */ + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE0), 0x10000000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0x68782800); + break; + + case 1: + mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE1), 0x10001000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0x68782800); + break; + + case 2: + mtdcr(DCRN_PEGPL_REGBAH(PCIE2), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE2), 0x10002000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE2), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE2), 0x68782800); + } + + utl_base = ioremap64(0xc10000000ull + 0x1000 * port, 0x100); + + /* + * Set buffer allocations and then assert VRB and TXE. + */ + out_be32(utl_base + PEUTL_OUTTR, 0x08000000); + out_be32(utl_base + PEUTL_INTR, 0x02000000); + out_be32(utl_base + PEUTL_OPDBSZ, 0x10000000); + out_be32(utl_base + PEUTL_PBBSZ, 0x53000000); + out_be32(utl_base + PEUTL_IPHBSZ, 0x08000000); + out_be32(utl_base + PEUTL_IPDBSZ, 0x10000000); + out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000); + out_be32(utl_base + PEUTL_PCTL, 0x80800066); + + iounmap(utl_base); + + /* + * We map PCI Express configuration access into the 512MB regions + * PCIE0: 0xc_4000_0000 + * PCIE1: 0xc_8000_0000 + * PCIE2: 0xc_c000_0000 + */ + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); + mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ + break; + + case 1: + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); + mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ + break; + + case 2: + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); + mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ + break; + } + + /* + * Check for VC0 active and assert RDY. + */ + switch (port) { + case 0: + if (!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) + printk(KERN_WARNING "PCIE0: VC0 not active\n"); + SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); + break; + case 1: + if (!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) + printk(KERN_WARNING "PCIE0: VC0 not active\n"); + SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); + break; + case 2: + if (!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) + printk(KERN_WARNING "PCIE0: VC0 not active\n"); + SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); + break; + } + +#if 0 + /* Dump all config regs */ + for (i = 0x300; i <= 0x320; ++i) + printk("[%04x] 0x%08x\n", i, SDR_READ(i)); + for (i = 0x340; i <= 0x353; ++i) + printk("[%04x] 0x%08x\n", i, SDR_READ(i)); + for (i = 0x370; i <= 0x383; ++i) + printk("[%04x] 0x%08x\n", i, SDR_READ(i)); + for (i = 0x3a0; i <= 0x3a2; ++i) + printk("[%04x] 0x%08x\n", i, SDR_READ(i)); + for (i = 0x3c0; i <= 0x3c3; ++i) + printk("[%04x] 0x%08x\n", i, SDR_READ(i)); +#endif + + mdelay(100); + + return 0; +} + +void ppc440spe_setup_pcie(struct pci_controller *hose, int port) +{ + void __iomem *mbase; + + /* + * Map 16MB, which is enough for 4 bits of bus # + */ + hose->cfg_data = ioremap64(0xc40000000ull + port * 0x40000000, + 1 << 24); + hose->ops = &pcie_pci_ops; + + /* + * Set bus numbers on our root port + */ + mbase = ioremap64(0xc50000000ull + port * 0x40000000, 4096); + out_8(mbase + PCI_PRIMARY_BUS, 0); + out_8(mbase + PCI_SECONDARY_BUS, 0); + + /* + * Set up outbound translation to hose->mem_space from PLB + * addresses at an offset of 0xd_0000_0000. We set the low + * bits of the mask to 11 to turn off splitting into 8 + * subregions and to enable the outbound translation. + */ + out_le32(mbase + PECFG_POM0LAH, 0); + out_le32(mbase + PECFG_POM0LAL, hose->mem_space.start); + + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), hose->mem_space.start); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), + ~(hose->mem_space.end - hose->mem_space.start) | 3); + break; + case 1: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), hose->mem_space.start); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), + ~(hose->mem_space.end - hose->mem_space.start) | 3); + + break; + case 2: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), hose->mem_space.start); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), + ~(hose->mem_space.end - hose->mem_space.start) | 3); + break; + } + + /* Set up 16GB inbound memory window at 0 */ + out_le32(mbase + PCI_BASE_ADDRESS_0, 0); + out_le32(mbase + PCI_BASE_ADDRESS_1, 0); + out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); + out_le32(mbase + PECFG_BAR0LMPA, 0); + out_le32(mbase + PECFG_PIM0LAL, 0); + out_le32(mbase + PECFG_PIM0LAH, 0); + out_le32(mbase + PECFG_PIMEN, 0x1); + + /* Enable I/O, Mem, and Busmaster cycles */ + out_le16(mbase + PCI_COMMAND, + in_le16(mbase + PCI_COMMAND) | + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + + iounmap(mbase); +} diff --git a/arch/ppc/syslib/ppc440spe_pcie.h b/arch/ppc/syslib/ppc440spe_pcie.h new file mode 100644 index 0000000..55b765a --- /dev/null +++ b/arch/ppc/syslib/ppc440spe_pcie.h @@ -0,0 +1,149 @@ +/* + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * Roland Dreier <rolandd@cisco.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __PPC_SYSLIB_PPC440SPE_PCIE_H +#define __PPC_SYSLIB_PPC440SPE_PCIE_H + +#define DCRN_SDR0_CFGADDR 0x00e +#define DCRN_SDR0_CFGDATA 0x00f + +#define DCRN_PCIE0_BASE 0x100 +#define DCRN_PCIE1_BASE 0x120 +#define DCRN_PCIE2_BASE 0x140 +#define PCIE0 DCRN_PCIE0_BASE +#define PCIE1 DCRN_PCIE1_BASE +#define PCIE2 DCRN_PCIE2_BASE + +#define DCRN_PEGPL_CFGBAH(base) (base + 0x00) +#define DCRN_PEGPL_CFGBAL(base) (base + 0x01) +#define DCRN_PEGPL_CFGMSK(base) (base + 0x02) +#define DCRN_PEGPL_MSGBAH(base) (base + 0x03) +#define DCRN_PEGPL_MSGBAL(base) (base + 0x04) +#define DCRN_PEGPL_MSGMSK(base) (base + 0x05) +#define DCRN_PEGPL_OMR1BAH(base) (base + 0x06) +#define DCRN_PEGPL_OMR1BAL(base) (base + 0x07) +#define DCRN_PEGPL_OMR1MSKH(base) (base + 0x08) +#define DCRN_PEGPL_OMR1MSKL(base) (base + 0x09) +#define DCRN_PEGPL_REGBAH(base) (base + 0x12) +#define DCRN_PEGPL_REGBAL(base) (base + 0x13) +#define DCRN_PEGPL_REGMSK(base) (base + 0x14) +#define DCRN_PEGPL_SPECIAL(base) (base + 0x15) + +/* + * System DCRs (SDRs) + */ +#define PESDR0_PLLLCT1 0x03a0 +#define PESDR0_PLLLCT2 0x03a1 +#define PESDR0_PLLLCT3 0x03a2 + +#define PESDR0_UTLSET1 0x0300 +#define PESDR0_UTLSET2 0x0301 +#define PESDR0_DLPSET 0x0302 +#define PESDR0_LOOP 0x0303 +#define PESDR0_RCSSET 0x0304 +#define PESDR0_RCSSTS 0x0305 +#define PESDR0_HSSL0SET1 0x0306 +#define PESDR0_HSSL0SET2 0x0307 +#define PESDR0_HSSL0STS 0x0308 +#define PESDR0_HSSL1SET1 0x0309 +#define PESDR0_HSSL1SET2 0x030a +#define PESDR0_HSSL1STS 0x030b +#define PESDR0_HSSL2SET1 0x030c +#define PESDR0_HSSL2SET2 0x030d +#define PESDR0_HSSL2STS 0x030e +#define PESDR0_HSSL3SET1 0x030f +#define PESDR0_HSSL3SET2 0x0310 +#define PESDR0_HSSL3STS 0x0311 +#define PESDR0_HSSL4SET1 0x0312 +#define PESDR0_HSSL4SET2 0x0313 +#define PESDR0_HSSL4STS 0x0314 +#define PESDR0_HSSL5SET1 0x0315 +#define PESDR0_HSSL5SET2 0x0316 +#define PESDR0_HSSL5STS 0x0317 +#define PESDR0_HSSL6SET1 0x0318 +#define PESDR0_HSSL6SET2 0x0319 +#define PESDR0_HSSL6STS 0x031a +#define PESDR0_HSSL7SET1 0x031b +#define PESDR0_HSSL7SET2 0x031c +#define PESDR0_HSSL7STS 0x031d +#define PESDR0_HSSCTLSET 0x031e +#define PESDR0_LANE_ABCD 0x031f +#define PESDR0_LANE_EFGH 0x0320 + +#define PESDR1_UTLSET1 0x0340 +#define PESDR1_UTLSET2 0x0341 +#define PESDR1_DLPSET 0x0342 +#define PESDR1_LOOP 0x0343 +#define PESDR1_RCSSET 0x0344 +#define PESDR1_RCSSTS 0x0345 +#define PESDR1_HSSL0SET1 0x0346 +#define PESDR1_HSSL0SET2 0x0347 +#define PESDR1_HSSL0STS 0x0348 +#define PESDR1_HSSL1SET1 0x0349 +#define PESDR1_HSSL1SET2 0x034a +#define PESDR1_HSSL1STS 0x034b +#define PESDR1_HSSL2SET1 0x034c +#define PESDR1_HSSL2SET2 0x034d +#define PESDR1_HSSL2STS 0x034e +#define PESDR1_HSSL3SET1 0x034f +#define PESDR1_HSSL3SET2 0x0350 +#define PESDR1_HSSL3STS 0x0351 +#define PESDR1_HSSCTLSET 0x0352 +#define PESDR1_LANE_ABCD 0x0353 + +#define PESDR2_UTLSET1 0x0370 +#define PESDR2_UTLSET2 0x0371 +#define PESDR2_DLPSET 0x0372 +#define PESDR2_LOOP 0x0373 +#define PESDR2_RCSSET 0x0374 +#define PESDR2_RCSSTS 0x0375 +#define PESDR2_HSSL0SET1 0x0376 +#define PESDR2_HSSL0SET2 0x0377 +#define PESDR2_HSSL0STS 0x0378 +#define PESDR2_HSSL1SET1 0x0379 +#define PESDR2_HSSL1SET2 0x037a +#define PESDR2_HSSL1STS 0x037b +#define PESDR2_HSSL2SET1 0x037c +#define PESDR2_HSSL2SET2 0x037d +#define PESDR2_HSSL2STS 0x037e +#define PESDR2_HSSL3SET1 0x037f +#define PESDR2_HSSL3SET2 0x0380 +#define PESDR2_HSSL3STS 0x0381 +#define PESDR2_HSSCTLSET 0x0382 +#define PESDR2_LANE_ABCD 0x0383 + +/* + * UTL register offsets + */ +#define PEUTL_PBBSZ 0x20 +#define PEUTL_OPDBSZ 0x68 +#define PEUTL_IPHBSZ 0x70 +#define PEUTL_IPDBSZ 0x78 +#define PEUTL_OUTTR 0x90 +#define PEUTL_INTR 0x98 +#define PEUTL_PCTL 0xa0 +#define PEUTL_RCIRQEN 0xb8 + +/* + * Config space register offsets + */ +#define PECFG_BAR0LMPA 0x210 +#define PECFG_BAR0HMPA 0x214 +#define PECFG_PIMEN 0x33c +#define PECFG_PIM0LAL 0x340 +#define PECFG_PIM0LAH 0x344 +#define PECFG_POM0LAL 0x380 +#define PECFG_POM0LAH 0x384 + +int ppc440spe_init_pcie(void); +int ppc440spe_init_pcie_rootport(int port); +void ppc440spe_setup_pcie(struct pci_controller *hose, int port); + +#endif /* __PPC_SYSLIB_PPC440SPE_PCIE_H */ diff --git a/arch/ppc/syslib/ppc4xx_pic.c b/arch/ppc/syslib/ppc4xx_pic.c index 0b43563..aa41651 100644 --- a/arch/ppc/syslib/ppc4xx_pic.c +++ b/arch/ppc/syslib/ppc4xx_pic.c @@ -38,6 +38,7 @@ extern unsigned char ppc4xx_uic_ext_irq_cfg[] __attribute__ ((weak)); #define IRQ_MASK_UICx(irq) (1 << (31 - ((irq) & 0x1f))) #define IRQ_MASK_UIC1(irq) IRQ_MASK_UICx(irq) #define IRQ_MASK_UIC2(irq) IRQ_MASK_UICx(irq) +#define IRQ_MASK_UIC3(irq) IRQ_MASK_UICx(irq) #define UIC_HANDLERS(n) \ static void ppc4xx_uic##n##_enable(unsigned int irq) \ @@ -88,7 +89,38 @@ static void ppc4xx_uic##n##_end(unsigned int irq) \ .end = ppc4xx_uic##n##_end, \ } \ -#if NR_UICS == 3 +#if NR_UICS == 4 +#define ACK_UIC0_PARENT +#define ACK_UIC1_PARENT mtdcr(DCRN_UIC_SR(UIC0), UIC0_UIC1NC); +#define ACK_UIC2_PARENT mtdcr(DCRN_UIC_SR(UIC0), UIC0_UIC2NC); +#define ACK_UIC3_PARENT mtdcr(DCRN_UIC_SR(UIC0), UIC0_UIC3NC); +UIC_HANDLERS(0); +UIC_HANDLERS(1); +UIC_HANDLERS(2); +UIC_HANDLERS(3); + +static int ppc4xx_pic_get_irq(struct pt_regs *regs) +{ + u32 uic0 = mfdcr(DCRN_UIC_MSR(UIC0)); + if (uic0 & UIC0_UIC1NC) + return 64 - ffs(mfdcr(DCRN_UIC_MSR(UIC1))); + else if (uic0 & UIC0_UIC2NC) + return 96 - ffs(mfdcr(DCRN_UIC_MSR(UIC2))); + else if (uic0 & UIC0_UIC3NC) + return 128 - ffs(mfdcr(DCRN_UIC_MSR(UIC3))); + else + return uic0 ? 32 - ffs(uic0) : -1; +} + +static void __init ppc4xx_pic_impl_init(void) +{ + /* Enable cascade interrupts in UIC0 */ + ppc_cached_irq_mask[0] |= UIC0_UIC1NC | UIC0_UIC2NC | UIC0_UIC3NC; + mtdcr(DCRN_UIC_SR(UIC0), UIC0_UIC1NC | UIC0_UIC2NC | UIC0_UIC3NC); + mtdcr(DCRN_UIC_ER(UIC0), ppc_cached_irq_mask[0]); +} + +#elif NR_UICS == 3 #define ACK_UIC0_PARENT mtdcr(DCRN_UIC_SR(UICB), UICB_UIC0NC); #define ACK_UIC1_PARENT mtdcr(DCRN_UIC_SR(UICB), UICB_UIC1NC); #define ACK_UIC2_PARENT mtdcr(DCRN_UIC_SR(UICB), UICB_UIC2NC); @@ -170,6 +202,9 @@ static struct ppc4xx_uic_impl { { .decl = DECLARE_UIC(1), .base = UIC1 }, #if NR_UICS > 2 { .decl = DECLARE_UIC(2), .base = UIC2 }, +#if NR_UICS > 3 + { .decl = DECLARE_UIC(3), .base = UIC3 }, +#endif #endif #endif }; diff --git a/arch/ppc/syslib/ppc85xx_rio.c b/arch/ppc/syslib/ppc85xx_rio.c new file mode 100644 index 0000000..297f3b5 --- /dev/null +++ b/arch/ppc/syslib/ppc85xx_rio.c @@ -0,0 +1,938 @@ +/* + * MPC85xx RapidIO support + * + * Copyright 2005 MontaVista Software, Inc. + * Matt Porter <mporter@kernel.crashing.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/types.h> +#include <linux/dma-mapping.h> +#include <linux/interrupt.h> +#include <linux/rio.h> +#include <linux/rio_drv.h> + +#include <asm/io.h> + +#define RIO_REGS_BASE (CCSRBAR + 0xc0000) +#define RIO_ATMU_REGS_OFFSET 0x10c00 +#define RIO_MSG_REGS_OFFSET 0x11000 +#define RIO_MAINT_WIN_SIZE 0x400000 +#define RIO_DBELL_WIN_SIZE 0x1000 + +#define RIO_MSG_OMR_MUI 0x00000002 +#define RIO_MSG_OSR_TE 0x00000080 +#define RIO_MSG_OSR_QOI 0x00000020 +#define RIO_MSG_OSR_QFI 0x00000010 +#define RIO_MSG_OSR_MUB 0x00000004 +#define RIO_MSG_OSR_EOMI 0x00000002 +#define RIO_MSG_OSR_QEI 0x00000001 + +#define RIO_MSG_IMR_MI 0x00000002 +#define RIO_MSG_ISR_TE 0x00000080 +#define RIO_MSG_ISR_QFI 0x00000010 +#define RIO_MSG_ISR_DIQI 0x00000001 + +#define RIO_MSG_DESC_SIZE 32 +#define RIO_MSG_BUFFER_SIZE 4096 +#define RIO_MIN_TX_RING_SIZE 2 +#define RIO_MAX_TX_RING_SIZE 2048 +#define RIO_MIN_RX_RING_SIZE 2 +#define RIO_MAX_RX_RING_SIZE 2048 + +#define DOORBELL_DMR_DI 0x00000002 +#define DOORBELL_DSR_TE 0x00000080 +#define DOORBELL_DSR_QFI 0x00000010 +#define DOORBELL_DSR_DIQI 0x00000001 +#define DOORBELL_TID_OFFSET 0x03 +#define DOORBELL_SID_OFFSET 0x05 +#define DOORBELL_INFO_OFFSET 0x06 + +#define DOORBELL_MESSAGE_SIZE 0x08 +#define DBELL_SID(x) (*(u8 *)(x + DOORBELL_SID_OFFSET)) +#define DBELL_TID(x) (*(u8 *)(x + DOORBELL_TID_OFFSET)) +#define DBELL_INF(x) (*(u16 *)(x + DOORBELL_INFO_OFFSET)) + +#define is_power_of_2(x) (((x) & ((x) - 1)) == 0) + +struct rio_atmu_regs { + u32 rowtar; + u32 pad1; + u32 rowbar; + u32 pad2; + u32 rowar; + u32 pad3[3]; +}; + +struct rio_msg_regs { + u32 omr; + u32 osr; + u32 pad1; + u32 odqdpar; + u32 pad2; + u32 osar; + u32 odpr; + u32 odatr; + u32 odcr; + u32 pad3; + u32 odqepar; + u32 pad4[13]; + u32 imr; + u32 isr; + u32 pad5; + u32 ifqdpar; + u32 pad6; + u32 ifqepar; + u32 pad7[250]; + u32 dmr; + u32 dsr; + u32 pad8; + u32 dqdpar; + u32 pad9; + u32 dqepar; + u32 pad10[26]; + u32 pwmr; + u32 pwsr; + u32 pad11; + u32 pwqbar; +}; + +struct rio_tx_desc { + u32 res1; + u32 saddr; + u32 dport; + u32 dattr; + u32 res2; + u32 res3; + u32 dwcnt; + u32 res4; +}; + +static u32 regs_win; +static struct rio_atmu_regs *atmu_regs; +static struct rio_atmu_regs *maint_atmu_regs; +static struct rio_atmu_regs *dbell_atmu_regs; +static u32 dbell_win; +static u32 maint_win; +static struct rio_msg_regs *msg_regs; + +static struct rio_dbell_ring { + void *virt; + dma_addr_t phys; +} dbell_ring; + +static struct rio_msg_tx_ring { + void *virt; + dma_addr_t phys; + void *virt_buffer[RIO_MAX_TX_RING_SIZE]; + dma_addr_t phys_buffer[RIO_MAX_TX_RING_SIZE]; + int tx_slot; + int size; + void *dev_id; +} msg_tx_ring; + +static struct rio_msg_rx_ring { + void *virt; + dma_addr_t phys; + void *virt_buffer[RIO_MAX_RX_RING_SIZE]; + int rx_slot; + int size; + void *dev_id; +} msg_rx_ring; + +/** + * mpc85xx_rio_doorbell_send - Send a MPC85xx doorbell message + * @index: ID of RapidIO interface + * @destid: Destination ID of target device + * @data: 16-bit info field of RapidIO doorbell message + * + * Sends a MPC85xx doorbell message. Returns %0 on success or + * %-EINVAL on failure. + */ +static int mpc85xx_rio_doorbell_send(int index, u16 destid, u16 data) +{ + pr_debug("mpc85xx_doorbell_send: index %d destid %4.4x data %4.4x\n", + index, destid, data); + out_be32((void *)&dbell_atmu_regs->rowtar, destid << 22); + out_be16((void *)(dbell_win), data); + + return 0; +} + +/** + * mpc85xx_local_config_read - Generate a MPC85xx local config space read + * @index: ID of RapdiIO interface + * @offset: Offset into configuration space + * @len: Length (in bytes) of the maintenance transaction + * @data: Value to be read into + * + * Generates a MPC85xx local configuration space read. Returns %0 on + * success or %-EINVAL on failure. + */ +static int mpc85xx_local_config_read(int index, u32 offset, int len, u32 * data) +{ + pr_debug("mpc85xx_local_config_read: index %d offset %8.8x\n", index, + offset); + *data = in_be32((void *)(regs_win + offset)); + + return 0; +} + +/** + * mpc85xx_local_config_write - Generate a MPC85xx local config space write + * @index: ID of RapdiIO interface + * @offset: Offset into configuration space + * @len: Length (in bytes) of the maintenance transaction + * @data: Value to be written + * + * Generates a MPC85xx local configuration space write. Returns %0 on + * success or %-EINVAL on failure. + */ +static int mpc85xx_local_config_write(int index, u32 offset, int len, u32 data) +{ + pr_debug + ("mpc85xx_local_config_write: index %d offset %8.8x data %8.8x\n", + index, offset, data); + out_be32((void *)(regs_win + offset), data); + + return 0; +} + +/** + * mpc85xx_rio_config_read - Generate a MPC85xx read maintenance transaction + * @index: ID of RapdiIO interface + * @destid: Destination ID of transaction + * @hopcount: Number of hops to target device + * @offset: Offset into configuration space + * @len: Length (in bytes) of the maintenance transaction + * @val: Location to be read into + * + * Generates a MPC85xx read maintenance transaction. Returns %0 on + * success or %-EINVAL on failure. + */ +static int +mpc85xx_rio_config_read(int index, u16 destid, u8 hopcount, u32 offset, int len, + u32 * val) +{ + u8 *data; + + pr_debug + ("mpc85xx_rio_config_read: index %d destid %d hopcount %d offset %8.8x len %d\n", + index, destid, hopcount, offset, len); + out_be32((void *)&maint_atmu_regs->rowtar, + (destid << 22) | (hopcount << 12) | ((offset & ~0x3) >> 9)); + + data = (u8 *) maint_win + offset; + switch (len) { + case 1: + *val = in_8((u8 *) data); + break; + case 2: + *val = in_be16((u16 *) data); + break; + default: + *val = in_be32((u32 *) data); + break; + } + + return 0; +} + +/** + * mpc85xx_rio_config_write - Generate a MPC85xx write maintenance transaction + * @index: ID of RapdiIO interface + * @destid: Destination ID of transaction + * @hopcount: Number of hops to target device + * @offset: Offset into configuration space + * @len: Length (in bytes) of the maintenance transaction + * @val: Value to be written + * + * Generates an MPC85xx write maintenance transaction. Returns %0 on + * success or %-EINVAL on failure. + */ +static int +mpc85xx_rio_config_write(int index, u16 destid, u8 hopcount, u32 offset, + int len, u32 val) +{ + u8 *data; + pr_debug + ("mpc85xx_rio_config_write: index %d destid %d hopcount %d offset %8.8x len %d val %8.8x\n", + index, destid, hopcount, offset, len, val); + out_be32((void *)&maint_atmu_regs->rowtar, + (destid << 22) | (hopcount << 12) | ((offset & ~0x3) >> 9)); + + data = (u8 *) maint_win + offset; + switch (len) { + case 1: + out_8((u8 *) data, val); + break; + case 2: + out_be16((u16 *) data, val); + break; + default: + out_be32((u32 *) data, val); + break; + } + + return 0; +} + +/** + * rio_hw_add_outb_message - Add message to the MPC85xx outbound message queue + * @mport: Master port with outbound message queue + * @rdev: Target of outbound message + * @mbox: Outbound mailbox + * @buffer: Message to add to outbound queue + * @len: Length of message + * + * Adds the @buffer message to the MPC85xx outbound message queue. Returns + * %0 on success or %-EINVAL on failure. + */ +int +rio_hw_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox, + void *buffer, size_t len) +{ + u32 omr; + struct rio_tx_desc *desc = + (struct rio_tx_desc *)msg_tx_ring.virt + msg_tx_ring.tx_slot; + int ret = 0; + + pr_debug + ("RIO: rio_hw_add_outb_message(): destid %4.4x mbox %d buffer %8.8x len %8.8x\n", + rdev->destid, mbox, (int)buffer, len); + + if ((len < 8) || (len > RIO_MAX_MSG_SIZE)) { + ret = -EINVAL; + goto out; + } + + /* Copy and clear rest of buffer */ + memcpy(msg_tx_ring.virt_buffer[msg_tx_ring.tx_slot], buffer, len); + if (len < (RIO_MAX_MSG_SIZE - 4)) + memset((void *)((u32) msg_tx_ring. + virt_buffer[msg_tx_ring.tx_slot] + len), 0, + RIO_MAX_MSG_SIZE - len); + + /* Set mbox field for message */ + desc->dport = mbox & 0x3; + + /* Enable EOMI interrupt, set priority, and set destid */ + desc->dattr = 0x28000000 | (rdev->destid << 2); + + /* Set transfer size aligned to next power of 2 (in double words) */ + desc->dwcnt = is_power_of_2(len) ? len : 1 << get_bitmask_order(len); + + /* Set snooping and source buffer address */ + desc->saddr = 0x00000004 | msg_tx_ring.phys_buffer[msg_tx_ring.tx_slot]; + + /* Increment enqueue pointer */ + omr = in_be32((void *)&msg_regs->omr); + out_be32((void *)&msg_regs->omr, omr | RIO_MSG_OMR_MUI); + + /* Go to next descriptor */ + if (++msg_tx_ring.tx_slot == msg_tx_ring.size) + msg_tx_ring.tx_slot = 0; + + out: + return ret; +} + +EXPORT_SYMBOL_GPL(rio_hw_add_outb_message); + +/** + * mpc85xx_rio_tx_handler - MPC85xx outbound message interrupt handler + * @irq: Linux interrupt number + * @dev_instance: Pointer to interrupt-specific data + * @regs: Register context + * + * Handles outbound message interrupts. Executes a register outbound + * mailbox event handler and acks the interrupt occurence. + */ +static irqreturn_t +mpc85xx_rio_tx_handler(int irq, void *dev_instance, struct pt_regs *regs) +{ + int osr; + struct rio_mport *port = (struct rio_mport *)dev_instance; + + osr = in_be32((void *)&msg_regs->osr); + + if (osr & RIO_MSG_OSR_TE) { + pr_info("RIO: outbound message transmission error\n"); + out_be32((void *)&msg_regs->osr, RIO_MSG_OSR_TE); + goto out; + } + + if (osr & RIO_MSG_OSR_QOI) { + pr_info("RIO: outbound message queue overflow\n"); + out_be32((void *)&msg_regs->osr, RIO_MSG_OSR_QOI); + goto out; + } + + if (osr & RIO_MSG_OSR_EOMI) { + u32 dqp = in_be32((void *)&msg_regs->odqdpar); + int slot = (dqp - msg_tx_ring.phys) >> 5; + port->outb_msg[0].mcback(port, msg_tx_ring.dev_id, -1, slot); + + /* Ack the end-of-message interrupt */ + out_be32((void *)&msg_regs->osr, RIO_MSG_OSR_EOMI); + } + + out: + return IRQ_HANDLED; +} + +/** + * rio_open_outb_mbox - Initialize MPC85xx outbound mailbox + * @mport: Master port implementing the outbound message unit + * @dev_id: Device specific pointer to pass on event + * @mbox: Mailbox to open + * @entries: Number of entries in the outbound mailbox ring + * + * Initializes buffer ring, request the outbound message interrupt, + * and enables the outbound message unit. Returns %0 on success and + * %-EINVAL or %-ENOMEM on failure. + */ +int rio_open_outb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries) +{ + int i, j, rc = 0; + + if ((entries < RIO_MIN_TX_RING_SIZE) || + (entries > RIO_MAX_TX_RING_SIZE) || (!is_power_of_2(entries))) { + rc = -EINVAL; + goto out; + } + + /* Initialize shadow copy ring */ + msg_tx_ring.dev_id = dev_id; + msg_tx_ring.size = entries; + + for (i = 0; i < msg_tx_ring.size; i++) { + if (! + (msg_tx_ring.virt_buffer[i] = + dma_alloc_coherent(NULL, RIO_MSG_BUFFER_SIZE, + &msg_tx_ring.phys_buffer[i], + GFP_KERNEL))) { + rc = -ENOMEM; + for (j = 0; j < msg_tx_ring.size; j++) + if (msg_tx_ring.virt_buffer[j]) + dma_free_coherent(NULL, + RIO_MSG_BUFFER_SIZE, + msg_tx_ring. + virt_buffer[j], + msg_tx_ring. + phys_buffer[j]); + goto out; + } + } + + /* Initialize outbound message descriptor ring */ + if (!(msg_tx_ring.virt = dma_alloc_coherent(NULL, + msg_tx_ring.size * + RIO_MSG_DESC_SIZE, + &msg_tx_ring.phys, + GFP_KERNEL))) { + rc = -ENOMEM; + goto out_dma; + } + memset(msg_tx_ring.virt, 0, msg_tx_ring.size * RIO_MSG_DESC_SIZE); + msg_tx_ring.tx_slot = 0; + + /* Point dequeue/enqueue pointers at first entry in ring */ + out_be32((void *)&msg_regs->odqdpar, msg_tx_ring.phys); + out_be32((void *)&msg_regs->odqepar, msg_tx_ring.phys); + + /* Configure for snooping */ + out_be32((void *)&msg_regs->osar, 0x00000004); + + /* Clear interrupt status */ + out_be32((void *)&msg_regs->osr, 0x000000b3); + + /* Hook up outbound message handler */ + if ((rc = + request_irq(MPC85xx_IRQ_RIO_TX, mpc85xx_rio_tx_handler, 0, + "msg_tx", (void *)mport)) < 0) + goto out_irq; + + /* + * Configure outbound message unit + * Snooping + * Interrupts (all enabled, except QEIE) + * Chaining mode + * Disable + */ + out_be32((void *)&msg_regs->omr, 0x00100220); + + /* Set number of entries */ + out_be32((void *)&msg_regs->omr, + in_be32((void *)&msg_regs->omr) | + ((get_bitmask_order(entries) - 2) << 12)); + + /* Now enable the unit */ + out_be32((void *)&msg_regs->omr, in_be32((void *)&msg_regs->omr) | 0x1); + + out: + return rc; + + out_irq: + dma_free_coherent(NULL, msg_tx_ring.size * RIO_MSG_DESC_SIZE, + msg_tx_ring.virt, msg_tx_ring.phys); + + out_dma: + for (i = 0; i < msg_tx_ring.size; i++) + dma_free_coherent(NULL, RIO_MSG_BUFFER_SIZE, + msg_tx_ring.virt_buffer[i], + msg_tx_ring.phys_buffer[i]); + + return rc; +} + +/** + * rio_close_outb_mbox - Shut down MPC85xx outbound mailbox + * @mport: Master port implementing the outbound message unit + * @mbox: Mailbox to close + * + * Disables the outbound message unit, free all buffers, and + * frees the outbound message interrupt. + */ +void rio_close_outb_mbox(struct rio_mport *mport, int mbox) +{ + /* Disable inbound message unit */ + out_be32((void *)&msg_regs->omr, 0); + + /* Free ring */ + dma_free_coherent(NULL, msg_tx_ring.size * RIO_MSG_DESC_SIZE, + msg_tx_ring.virt, msg_tx_ring.phys); + + /* Free interrupt */ + free_irq(MPC85xx_IRQ_RIO_TX, (void *)mport); +} + +/** + * mpc85xx_rio_rx_handler - MPC85xx inbound message interrupt handler + * @irq: Linux interrupt number + * @dev_instance: Pointer to interrupt-specific data + * @regs: Register context + * + * Handles inbound message interrupts. Executes a registered inbound + * mailbox event handler and acks the interrupt occurence. + */ +static irqreturn_t +mpc85xx_rio_rx_handler(int irq, void *dev_instance, struct pt_regs *regs) +{ + int isr; + struct rio_mport *port = (struct rio_mport *)dev_instance; + + isr = in_be32((void *)&msg_regs->isr); + + if (isr & RIO_MSG_ISR_TE) { + pr_info("RIO: inbound message reception error\n"); + out_be32((void *)&msg_regs->isr, RIO_MSG_ISR_TE); + goto out; + } + + /* XXX Need to check/dispatch until queue empty */ + if (isr & RIO_MSG_ISR_DIQI) { + /* + * We implement *only* mailbox 0, but can receive messages + * for any mailbox/letter to that mailbox destination. So, + * make the callback with an unknown/invalid mailbox number + * argument. + */ + port->inb_msg[0].mcback(port, msg_rx_ring.dev_id, -1, -1); + + /* Ack the queueing interrupt */ + out_be32((void *)&msg_regs->isr, RIO_MSG_ISR_DIQI); + } + + out: + return IRQ_HANDLED; +} + +/** + * rio_open_inb_mbox - Initialize MPC85xx inbound mailbox + * @mport: Master port implementing the inbound message unit + * @dev_id: Device specific pointer to pass on event + * @mbox: Mailbox to open + * @entries: Number of entries in the inbound mailbox ring + * + * Initializes buffer ring, request the inbound message interrupt, + * and enables the inbound message unit. Returns %0 on success + * and %-EINVAL or %-ENOMEM on failure. + */ +int rio_open_inb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries) +{ + int i, rc = 0; + + if ((entries < RIO_MIN_RX_RING_SIZE) || + (entries > RIO_MAX_RX_RING_SIZE) || (!is_power_of_2(entries))) { + rc = -EINVAL; + goto out; + } + + /* Initialize client buffer ring */ + msg_rx_ring.dev_id = dev_id; + msg_rx_ring.size = entries; + msg_rx_ring.rx_slot = 0; + for (i = 0; i < msg_rx_ring.size; i++) + msg_rx_ring.virt_buffer[i] = NULL; + + /* Initialize inbound message ring */ + if (!(msg_rx_ring.virt = dma_alloc_coherent(NULL, + msg_rx_ring.size * + RIO_MAX_MSG_SIZE, + &msg_rx_ring.phys, + GFP_KERNEL))) { + rc = -ENOMEM; + goto out; + } + + /* Point dequeue/enqueue pointers at first entry in ring */ + out_be32((void *)&msg_regs->ifqdpar, (u32) msg_rx_ring.phys); + out_be32((void *)&msg_regs->ifqepar, (u32) msg_rx_ring.phys); + + /* Clear interrupt status */ + out_be32((void *)&msg_regs->isr, 0x00000091); + + /* Hook up inbound message handler */ + if ((rc = + request_irq(MPC85xx_IRQ_RIO_RX, mpc85xx_rio_rx_handler, 0, + "msg_rx", (void *)mport)) < 0) { + dma_free_coherent(NULL, RIO_MSG_BUFFER_SIZE, + msg_tx_ring.virt_buffer[i], + msg_tx_ring.phys_buffer[i]); + goto out; + } + + /* + * Configure inbound message unit: + * Snooping + * 4KB max message size + * Unmask all interrupt sources + * Disable + */ + out_be32((void *)&msg_regs->imr, 0x001b0060); + + /* Set number of queue entries */ + out_be32((void *)&msg_regs->imr, + in_be32((void *)&msg_regs->imr) | + ((get_bitmask_order(entries) - 2) << 12)); + + /* Now enable the unit */ + out_be32((void *)&msg_regs->imr, in_be32((void *)&msg_regs->imr) | 0x1); + + out: + return rc; +} + +/** + * rio_close_inb_mbox - Shut down MPC85xx inbound mailbox + * @mport: Master port implementing the inbound message unit + * @mbox: Mailbox to close + * + * Disables the inbound message unit, free all buffers, and + * frees the inbound message interrupt. + */ +void rio_close_inb_mbox(struct rio_mport *mport, int mbox) +{ + /* Disable inbound message unit */ + out_be32((void *)&msg_regs->imr, 0); + + /* Free ring */ + dma_free_coherent(NULL, msg_rx_ring.size * RIO_MAX_MSG_SIZE, + msg_rx_ring.virt, msg_rx_ring.phys); + + /* Free interrupt */ + free_irq(MPC85xx_IRQ_RIO_RX, (void *)mport); +} + +/** + * rio_hw_add_inb_buffer - Add buffer to the MPC85xx inbound message queue + * @mport: Master port implementing the inbound message unit + * @mbox: Inbound mailbox number + * @buf: Buffer to add to inbound queue + * + * Adds the @buf buffer to the MPC85xx inbound message queue. Returns + * %0 on success or %-EINVAL on failure. + */ +int rio_hw_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf) +{ + int rc = 0; + + pr_debug("RIO: rio_hw_add_inb_buffer(), msg_rx_ring.rx_slot %d\n", + msg_rx_ring.rx_slot); + + if (msg_rx_ring.virt_buffer[msg_rx_ring.rx_slot]) { + printk(KERN_ERR + "RIO: error adding inbound buffer %d, buffer exists\n", + msg_rx_ring.rx_slot); + rc = -EINVAL; + goto out; + } + + msg_rx_ring.virt_buffer[msg_rx_ring.rx_slot] = buf; + if (++msg_rx_ring.rx_slot == msg_rx_ring.size) + msg_rx_ring.rx_slot = 0; + + out: + return rc; +} + +EXPORT_SYMBOL_GPL(rio_hw_add_inb_buffer); + +/** + * rio_hw_get_inb_message - Fetch inbound message from the MPC85xx message unit + * @mport: Master port implementing the inbound message unit + * @mbox: Inbound mailbox number + * + * Gets the next available inbound message from the inbound message queue. + * A pointer to the message is returned on success or NULL on failure. + */ +void *rio_hw_get_inb_message(struct rio_mport *mport, int mbox) +{ + u32 imr; + u32 phys_buf, virt_buf; + void *buf = NULL; + int buf_idx; + + phys_buf = in_be32((void *)&msg_regs->ifqdpar); + + /* If no more messages, then bail out */ + if (phys_buf == in_be32((void *)&msg_regs->ifqepar)) + goto out2; + + virt_buf = (u32) msg_rx_ring.virt + (phys_buf - msg_rx_ring.phys); + buf_idx = (phys_buf - msg_rx_ring.phys) / RIO_MAX_MSG_SIZE; + buf = msg_rx_ring.virt_buffer[buf_idx]; + + if (!buf) { + printk(KERN_ERR + "RIO: inbound message copy failed, no buffers\n"); + goto out1; + } + + /* Copy max message size, caller is expected to allocate that big */ + memcpy(buf, (void *)virt_buf, RIO_MAX_MSG_SIZE); + + /* Clear the available buffer */ + msg_rx_ring.virt_buffer[buf_idx] = NULL; + + out1: + imr = in_be32((void *)&msg_regs->imr); + out_be32((void *)&msg_regs->imr, imr | RIO_MSG_IMR_MI); + + out2: + return buf; +} + +EXPORT_SYMBOL_GPL(rio_hw_get_inb_message); + +/** + * mpc85xx_rio_dbell_handler - MPC85xx doorbell interrupt handler + * @irq: Linux interrupt number + * @dev_instance: Pointer to interrupt-specific data + * @regs: Register context + * + * Handles doorbell interrupts. Parses a list of registered + * doorbell event handlers and executes a matching event handler. + */ +static irqreturn_t +mpc85xx_rio_dbell_handler(int irq, void *dev_instance, struct pt_regs *regs) +{ + int dsr; + struct rio_mport *port = (struct rio_mport *)dev_instance; + + dsr = in_be32((void *)&msg_regs->dsr); + + if (dsr & DOORBELL_DSR_TE) { + pr_info("RIO: doorbell reception error\n"); + out_be32((void *)&msg_regs->dsr, DOORBELL_DSR_TE); + goto out; + } + + if (dsr & DOORBELL_DSR_QFI) { + pr_info("RIO: doorbell queue full\n"); + out_be32((void *)&msg_regs->dsr, DOORBELL_DSR_QFI); + goto out; + } + + /* XXX Need to check/dispatch until queue empty */ + if (dsr & DOORBELL_DSR_DIQI) { + u32 dmsg = + (u32) dbell_ring.virt + + (in_be32((void *)&msg_regs->dqdpar) & 0xfff); + u32 dmr; + struct rio_dbell *dbell; + int found = 0; + + pr_debug + ("RIO: processing doorbell, sid %2.2x tid %2.2x info %4.4x\n", + DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg)); + + list_for_each_entry(dbell, &port->dbells, node) { + if ((dbell->res->start <= DBELL_INF(dmsg)) && + (dbell->res->end >= DBELL_INF(dmsg))) { + found = 1; + break; + } + } + if (found) { + dbell->dinb(port, dbell->dev_id, DBELL_SID(dmsg), DBELL_TID(dmsg), + DBELL_INF(dmsg)); + } else { + pr_debug + ("RIO: spurious doorbell, sid %2.2x tid %2.2x info %4.4x\n", + DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg)); + } + dmr = in_be32((void *)&msg_regs->dmr); + out_be32((void *)&msg_regs->dmr, dmr | DOORBELL_DMR_DI); + out_be32((void *)&msg_regs->dsr, DOORBELL_DSR_DIQI); + } + + out: + return IRQ_HANDLED; +} + +/** + * mpc85xx_rio_doorbell_init - MPC85xx doorbell interface init + * @mport: Master port implementing the inbound doorbell unit + * + * Initializes doorbell unit hardware and inbound DMA buffer + * ring. Called from mpc85xx_rio_setup(). Returns %0 on success + * or %-ENOMEM on failure. + */ +static int mpc85xx_rio_doorbell_init(struct rio_mport *mport) +{ + int rc = 0; + + /* Map outbound doorbell window immediately after maintenance window */ + if (!(dbell_win = + (u32) ioremap(mport->iores.start + RIO_MAINT_WIN_SIZE, + RIO_DBELL_WIN_SIZE))) { + printk(KERN_ERR + "RIO: unable to map outbound doorbell window\n"); + rc = -ENOMEM; + goto out; + } + + /* Initialize inbound doorbells */ + if (!(dbell_ring.virt = dma_alloc_coherent(NULL, + 512 * DOORBELL_MESSAGE_SIZE, + &dbell_ring.phys, + GFP_KERNEL))) { + printk(KERN_ERR "RIO: unable allocate inbound doorbell ring\n"); + rc = -ENOMEM; + iounmap((void *)dbell_win); + goto out; + } + + /* Point dequeue/enqueue pointers at first entry in ring */ + out_be32((void *)&msg_regs->dqdpar, (u32) dbell_ring.phys); + out_be32((void *)&msg_regs->dqepar, (u32) dbell_ring.phys); + + /* Clear interrupt status */ + out_be32((void *)&msg_regs->dsr, 0x00000091); + + /* Hook up doorbell handler */ + if ((rc = + request_irq(MPC85xx_IRQ_RIO_BELL, mpc85xx_rio_dbell_handler, 0, + "dbell_rx", (void *)mport) < 0)) { + iounmap((void *)dbell_win); + dma_free_coherent(NULL, 512 * DOORBELL_MESSAGE_SIZE, + dbell_ring.virt, dbell_ring.phys); + printk(KERN_ERR + "MPC85xx RIO: unable to request inbound doorbell irq"); + goto out; + } + + /* Configure doorbells for snooping, 512 entries, and enable */ + out_be32((void *)&msg_regs->dmr, 0x00108161); + + out: + return rc; +} + +static char *cmdline = NULL; + +static int mpc85xx_rio_get_hdid(int index) +{ + /* XXX Need to parse multiple entries in some format */ + if (!cmdline) + return -1; + + return simple_strtol(cmdline, NULL, 0); +} + +static int mpc85xx_rio_get_cmdline(char *s) +{ + if (!s) + return 0; + + cmdline = s; + return 1; +} + +__setup("riohdid=", mpc85xx_rio_get_cmdline); + +/** + * mpc85xx_rio_setup - Setup MPC85xx RapidIO interface + * @law_start: Starting physical address of RapidIO LAW + * @law_size: Size of RapidIO LAW + * + * Initializes MPC85xx RapidIO hardware interface, configures + * master port with system-specific info, and registers the + * master port with the RapidIO subsystem. + */ +void mpc85xx_rio_setup(int law_start, int law_size) +{ + struct rio_ops *ops; + struct rio_mport *port; + + ops = kmalloc(sizeof(struct rio_ops), GFP_KERNEL); + ops->lcread = mpc85xx_local_config_read; + ops->lcwrite = mpc85xx_local_config_write; + ops->cread = mpc85xx_rio_config_read; + ops->cwrite = mpc85xx_rio_config_write; + ops->dsend = mpc85xx_rio_doorbell_send; + + port = kmalloc(sizeof(struct rio_mport), GFP_KERNEL); + port->id = 0; + port->index = 0; + INIT_LIST_HEAD(&port->dbells); + port->iores.start = law_start; + port->iores.end = law_start + law_size; + port->iores.flags = IORESOURCE_MEM; + + rio_init_dbell_res(&port->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff); + rio_init_mbox_res(&port->riores[RIO_INB_MBOX_RESOURCE], 0, 0); + rio_init_mbox_res(&port->riores[RIO_OUTB_MBOX_RESOURCE], 0, 0); + strcpy(port->name, "RIO0 mport"); + + port->ops = ops; + port->host_deviceid = mpc85xx_rio_get_hdid(port->id); + + rio_register_mport(port); + + regs_win = (u32) ioremap(RIO_REGS_BASE, 0x20000); + atmu_regs = (struct rio_atmu_regs *)(regs_win + RIO_ATMU_REGS_OFFSET); + maint_atmu_regs = atmu_regs + 1; + dbell_atmu_regs = atmu_regs + 2; + msg_regs = (struct rio_msg_regs *)(regs_win + RIO_MSG_REGS_OFFSET); + + /* Configure maintenance transaction window */ + out_be32((void *)&maint_atmu_regs->rowbar, 0x000c0000); + out_be32((void *)&maint_atmu_regs->rowar, 0x80077015); + + maint_win = (u32) ioremap(law_start, RIO_MAINT_WIN_SIZE); + + /* Configure outbound doorbell window */ + out_be32((void *)&dbell_atmu_regs->rowbar, 0x000c0400); + out_be32((void *)&dbell_atmu_regs->rowar, 0x8004200b); + mpc85xx_rio_doorbell_init(port); +} diff --git a/arch/ppc/syslib/ppc85xx_rio.h b/arch/ppc/syslib/ppc85xx_rio.h new file mode 100644 index 0000000..c0827a2 --- /dev/null +++ b/arch/ppc/syslib/ppc85xx_rio.h @@ -0,0 +1,21 @@ +/* + * MPC85xx RapidIO definitions + * + * Copyright 2005 MontaVista Software, Inc. + * Matt Porter <mporter@kernel.crashing.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __PPC_SYSLIB_PPC85XX_RIO_H +#define __PPC_SYSLIB_PPC85XX_RIO_H + +#include <linux/config.h> +#include <linux/init.h> + +extern void mpc85xx_rio_setup(int law_start, int law_size); + +#endif /* __PPC_SYSLIB_PPC85XX_RIO_H */ diff --git a/arch/ppc/syslib/ppc_sys.c b/arch/ppc/syslib/ppc_sys.c index 62ee86e..603f011 100644 --- a/arch/ppc/syslib/ppc_sys.c +++ b/arch/ppc/syslib/ppc_sys.c @@ -14,6 +14,7 @@ * option) any later version. */ +#include <linux/string.h> #include <asm/ppc_sys.h> int (*ppc_sys_device_fixup) (struct platform_device * pdev); diff --git a/arch/ppc/syslib/prom.c b/arch/ppc/syslib/prom.c index 278da6e..1b9aa0d 100644 --- a/arch/ppc/syslib/prom.c +++ b/arch/ppc/syslib/prom.c @@ -1335,10 +1335,8 @@ release_OF_resource(struct device_node* node, int index) if (!res) return -ENODEV; - if (res->name) { - kfree(res->name); - res->name = NULL; - } + kfree(res->name); + res->name = NULL; release_resource(res); kfree(res); |