amd64_edac: add F10h-and-later methods-p1

Borislav:

Fail f10_early_channel_count() if error encountered while reading a NB
register since those cached register contents are accessed afterwards.

- fix/cleanup comments
- fix function return value patterns
- cleanup debug calls

Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

1 files changed, 181 insertions, 0 deletions

diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c
index 24c031f..b4ef2c7 100644
--- a/drivers/edac/amd64_edac.c
+++ b/drivers/edac/amd64_edac.c
@@ -1185,4 +1185,185 @@ static int k8_dbam_map_to_pages(struct amd64_pvt *pvt, int dram_map)
 	return nr_pages;
 }
 
+/*
+ * Get the number of DCT channels in use.
+ *
+ * Return:
+ *	number of Memory Channels in operation
+ * Pass back:
+ *	contents of the DCL0_LOW register
+ */
+static int f10_early_channel_count(struct amd64_pvt *pvt)
+{
+	int err = 0, channels = 0;
+	u32 dbam;
+
+	err = pci_read_config_dword(pvt->dram_f2_ctl, F10_DCLR_0, &pvt->dclr0);
+	if (err)
+		goto err_reg;
+
+	err = pci_read_config_dword(pvt->dram_f2_ctl, F10_DCLR_1, &pvt->dclr1);
+	if (err)
+		goto err_reg;
+
+	/* If we are in 128 bit mode, then we are using 2 channels */
+	if (pvt->dclr0 & F10_WIDTH_128) {
+		debugf0("Data WIDTH is 128 bits - 2 channels\n");
+		channels = 2;
+		return channels;
+	}
+
+	/*
+	 * Need to check if in UN-ganged mode: In such, there are 2 channels,
+	 * but they are NOT in 128 bit mode and thus the above 'dcl0' status bit
+	 * will be OFF.
+	 *
+	 * Need to check DCT0[0] and DCT1[0] to see if only one of them has
+	 * their CSEnable bit on. If so, then SINGLE DIMM case.
+	 */
+	debugf0("Data WIDTH is NOT 128 bits - need more decoding\n");
 
+	/*
+	 * Check DRAM Bank Address Mapping values for each DIMM to see if there
+	 * is more than just one DIMM present in unganged mode. Need to check
+	 * both controllers since DIMMs can be placed in either one.
+	 */
+	channels = 0;
+	err = pci_read_config_dword(pvt->dram_f2_ctl, DBAM0, &dbam);
+	if (err)
+		goto err_reg;
+
+	if (DBAM_DIMM(0, dbam) > 0)
+		channels++;
+	if (DBAM_DIMM(1, dbam) > 0)
+		channels++;
+	if (DBAM_DIMM(2, dbam) > 0)
+		channels++;
+	if (DBAM_DIMM(3, dbam) > 0)
+		channels++;
+
+	/* If more than 2 DIMMs are present, then we have 2 channels */
+	if (channels > 2)
+		channels = 2;
+	else if (channels == 0) {
+		/* No DIMMs on DCT0, so look at DCT1 */
+		err = pci_read_config_dword(pvt->dram_f2_ctl, DBAM1, &dbam);
+		if (err)
+			goto err_reg;
+
+		if (DBAM_DIMM(0, dbam) > 0)
+			channels++;
+		if (DBAM_DIMM(1, dbam) > 0)
+			channels++;
+		if (DBAM_DIMM(2, dbam) > 0)
+			channels++;
+		if (DBAM_DIMM(3, dbam) > 0)
+			channels++;
+
+		if (channels > 2)
+			channels = 2;
+	}
+
+	/* If we found ALL 0 values, then assume just ONE DIMM-ONE Channel */
+	if (channels == 0)
+		channels = 1;
+
+	debugf0("DIMM count= %d\n", channels);
+
+	return channels;
+
+err_reg:
+	return -1;
+
+}
+
+static int f10_dbam_map_to_pages(struct amd64_pvt *pvt, int dram_map)
+{
+	return 1 << (revf_quad_ddr2_shift[dram_map] - PAGE_SHIFT);
+}
+
+/* Enable extended configuration access via 0xCF8 feature */
+static void amd64_setup(struct amd64_pvt *pvt)
+{
+	u32 reg;
+
+	pci_read_config_dword(pvt->misc_f3_ctl, F10_NB_CFG_HIGH, &reg);
+
+	pvt->flags.cf8_extcfg = !!(reg & F10_NB_CFG_LOW_ENABLE_EXT_CFG);
+	reg |= F10_NB_CFG_LOW_ENABLE_EXT_CFG;
+	pci_write_config_dword(pvt->misc_f3_ctl, F10_NB_CFG_HIGH, reg);
+}
+
+/* Restore the extended configuration access via 0xCF8 feature */
+static void amd64_teardown(struct amd64_pvt *pvt)
+{
+	u32 reg;
+
+	pci_read_config_dword(pvt->misc_f3_ctl, F10_NB_CFG_HIGH, &reg);
+
+	reg &= ~F10_NB_CFG_LOW_ENABLE_EXT_CFG;
+	if (pvt->flags.cf8_extcfg)
+		reg |= F10_NB_CFG_LOW_ENABLE_EXT_CFG;
+	pci_write_config_dword(pvt->misc_f3_ctl, F10_NB_CFG_HIGH, reg);
+}
+
+static u64 f10_get_error_address(struct mem_ctl_info *mci,
+			struct amd64_error_info_regs *info)
+{
+	return (((u64) (info->nbeah & 0xffff)) << 32) +
+			(info->nbeal & ~0x01);
+}
+
+/*
+ * Read the Base and Limit registers for F10 based Memory controllers. Extract
+ * fields from the 'raw' reg into separate data fields.
+ *
+ * Isolates: BASE, LIMIT, IntlvEn, IntlvSel, RW_EN.
+ */
+static void f10_read_dram_base_limit(struct amd64_pvt *pvt, int dram)
+{
+	u32 high_offset, low_offset, high_base, low_base, high_limit, low_limit;
+
+	low_offset = K8_DRAM_BASE_LOW + (dram << 3);
+	high_offset = F10_DRAM_BASE_HIGH + (dram << 3);
+
+	/* read the 'raw' DRAM BASE Address register */
+	pci_read_config_dword(pvt->addr_f1_ctl, low_offset, &low_base);
+
+	/* Read from the ECS data register */
+	pci_read_config_dword(pvt->addr_f1_ctl, high_offset, &high_base);
+
+	/* Extract parts into separate data entries */
+	pvt->dram_rw_en[dram] = (low_base & 0x3);
+
+	if (pvt->dram_rw_en[dram] == 0)
+		return;
+
+	pvt->dram_IntlvEn[dram] = (low_base >> 8) & 0x7;
+
+	pvt->dram_base[dram] = (((((u64) high_base & 0x000000FF) << 32) |
+				((u64) low_base & 0xFFFF0000))) << 8;
+
+	low_offset = K8_DRAM_LIMIT_LOW + (dram << 3);
+	high_offset = F10_DRAM_LIMIT_HIGH + (dram << 3);
+
+	/* read the 'raw' LIMIT registers */
+	pci_read_config_dword(pvt->addr_f1_ctl, low_offset, &low_limit);
+
+	/* Read from the ECS data register for the HIGH portion */
+	pci_read_config_dword(pvt->addr_f1_ctl, high_offset, &high_limit);
+
+	debugf0("  HW Regs: BASE=0x%08x-%08x      LIMIT=  0x%08x-%08x\n",
+		high_base, low_base, high_limit, low_limit);
+
+	pvt->dram_DstNode[dram] = (low_limit & 0x7);
+	pvt->dram_IntlvSel[dram] = (low_limit >> 8) & 0x7;
+
+	/*
+	 * Extract address values and form a LIMIT address. Limit is the HIGHEST
+	 * memory location of the region, so low 24 bits need to be all ones.
+	 */
+	low_limit |= 0x0000FFFF;
+	pvt->dram_limit[dram] =
+		((((u64) high_limit << 32) + (u64) low_limit) << 8) | (0xFF);
+}