diff options
author | Juerg Haefliger <juergh@gmail.com> | 2007-06-09 14:11:16 (GMT) |
---|---|---|
committer | Mark M. Hoffman <mhoffman@lightlink.com> | 2007-07-19 18:22:11 (GMT) |
commit | 9431996f55f8a3c04cdcb63895cf7661e135fadb (patch) | |
tree | 063732da70fa3fc5ff08f868962f4f07d4b1dfd2 /drivers/hwmon | |
parent | 87f0f31baf9ea2cb273d7fb56b3ebf9df5096884 (diff) | |
download | linux-fsl-qoriq-9431996f55f8a3c04cdcb63895cf7661e135fadb.tar.xz |
hwmon: New SMSC DME1737 driver
Add support for the hardware monitoring and fan control
capabilities of the SMSC DME1737 and Asus A8000 Super-I/O chips.
The hardware monitoring logic of this chip is similar to the LM85 but
has some additional features that this driver supports. Even though
it's a Super-I/O chip, the hardware monitoring logic can only be
accessed via SMBus.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Diffstat (limited to 'drivers/hwmon')
-rw-r--r-- | drivers/hwmon/Kconfig | 12 | ||||
-rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
-rw-r--r-- | drivers/hwmon/dme1737.c | 2080 |
3 files changed, 2093 insertions, 0 deletions
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 13eea47..f848e34 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -442,6 +442,18 @@ config SENSORS_SIS5595 This driver can also be built as a module. If so, the module will be called sis5595. +config SENSORS_DME1737 + tristate "SMSC DME1737 and compatibles" + depends on I2C && EXPERIMENTAL + select HWMON_VID + help + If you say yes here you get support for the hardware monitoring + and fan control features of the SMSC DME1737 (and compatibles + like the Asus A8000) Super-I/O chip. + + This driver can also be built as a module. If so, the module + will be called dme1737. + config SENSORS_SMSC47M1 tristate "SMSC LPC47M10x and compatibles" help diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index cfaf338..3618773 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -25,6 +25,7 @@ obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o obj-$(CONFIG_SENSORS_AMS) += ams/ obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o obj-$(CONFIG_SENSORS_CORETEMP) += coretemp.o +obj-$(CONFIG_SENSORS_DME1737) += dme1737.o obj-$(CONFIG_SENSORS_DS1621) += ds1621.o obj-$(CONFIG_SENSORS_F71805F) += f71805f.o obj-$(CONFIG_SENSORS_FSCHER) += fscher.o diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c new file mode 100644 index 0000000..be3aaa5 --- /dev/null +++ b/drivers/hwmon/dme1737.c @@ -0,0 +1,2080 @@ +/* + * dme1737.c - driver for the SMSC DME1737 and Asus A8000 Super-I/O chips + * integrated hardware monitoring features. + * Copyright (c) 2007 Juerg Haefliger <juergh@gmail.com> + * + * This driver is based on the LM85 driver. The hardware monitoring + * capabilities of the DME1737 are very similar to the LM85 with some + * additional features. Even though the DME1737 is a Super-I/O chip, the + * hardware monitoring registers are only accessible via SMBus. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/hwmon-vid.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <asm/io.h> + +/* Module load parameters */ +static int force_start; +module_param(force_start, bool, 0); +MODULE_PARM_DESC(force_start, "Force the chip to start monitoring inputs"); + +/* Addresses to scan */ +static unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END}; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(dme1737); + +/* --------------------------------------------------------------------- + * Registers + * + * The sensors are defined as follows: + * + * Voltages Temperatures + * -------- ------------ + * in0 +5VTR (+5V stdby) temp1 Remote diode 1 + * in1 Vccp (proc core) temp2 Internal temp + * in2 VCC (internal +3.3V) temp3 Remote diode 2 + * in3 +5V + * in4 +12V + * in5 VTR (+3.3V stby) + * in6 Vbat + * + * --------------------------------------------------------------------- */ + +/* Voltages (in) numbered 0-6 (ix) */ +#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) \ + : 0x94 + (ix)) +#define DME1737_REG_IN_MIN(ix) ((ix) < 5 ? 0x44 + (ix) * 2 \ + : 0x91 + (ix) * 2) +#define DME1737_REG_IN_MAX(ix) ((ix) < 5 ? 0x45 + (ix) * 2 \ + : 0x92 + (ix) * 2) + +/* Temperatures (temp) numbered 0-2 (ix) */ +#define DME1737_REG_TEMP(ix) (0x25 + (ix)) +#define DME1737_REG_TEMP_MIN(ix) (0x4e + (ix) * 2) +#define DME1737_REG_TEMP_MAX(ix) (0x4f + (ix) * 2) +#define DME1737_REG_TEMP_OFFSET(ix) ((ix) == 0 ? 0x1f \ + : 0x1c + (ix)) + +/* Voltage and temperature LSBs + * The LSBs (4 bits each) are stored in 5 registers with the following layouts: + * IN_TEMP_LSB(0) = [in5, in6] + * IN_TEMP_LSB(1) = [temp3, temp1] + * IN_TEMP_LSB(2) = [in4, temp2] + * IN_TEMP_LSB(3) = [in3, in0] + * IN_TEMP_LSB(4) = [in2, in1] */ +#define DME1737_REG_IN_TEMP_LSB(ix) (0x84 + (ix)) +static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0}; +static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4}; +static const u8 DME1737_REG_TEMP_LSB[] = {1, 2, 1}; +static const u8 DME1737_REG_TEMP_LSB_SHL[] = {4, 4, 0}; + +/* Fans numbered 0-5 (ix) */ +#define DME1737_REG_FAN(ix) ((ix) < 4 ? 0x28 + (ix) * 2 \ + : 0xa1 + (ix) * 2) +#define DME1737_REG_FAN_MIN(ix) ((ix) < 4 ? 0x54 + (ix) * 2 \ + : 0xa5 + (ix) * 2) +#define DME1737_REG_FAN_OPT(ix) ((ix) < 4 ? 0x90 + (ix) \ + : 0xb2 + (ix)) +#define DME1737_REG_FAN_MAX(ix) (0xb4 + (ix)) /* only for fan[4-5] */ + +/* PWMs numbered 0-2, 4-5 (ix) */ +#define DME1737_REG_PWM(ix) ((ix) < 3 ? 0x30 + (ix) \ + : 0xa1 + (ix)) +#define DME1737_REG_PWM_CONFIG(ix) (0x5c + (ix)) /* only for pwm[0-2] */ +#define DME1737_REG_PWM_MIN(ix) (0x64 + (ix)) /* only for pwm[0-2] */ +#define DME1737_REG_PWM_FREQ(ix) ((ix) < 3 ? 0x5f + (ix) \ + : 0xa3 + (ix)) +/* The layout of the ramp rate registers is different from the other pwm + * registers. The bits for the 3 PWMs are stored in 2 registers: + * PWM_RR(0) = [OFF3, OFF2, OFF1, RES, RR1E, RR1-2, RR1-1, RR1-0] + * PWM_RR(1) = [RR2E, RR2-2, RR2-1, RR2-0, RR3E, RR3-2, RR3-1, RR3-0] */ +#define DME1737_REG_PWM_RR(ix) (0x62 + (ix)) /* only for pwm[0-2] */ + +/* Thermal zones 0-2 */ +#define DME1737_REG_ZONE_LOW(ix) (0x67 + (ix)) +#define DME1737_REG_ZONE_ABS(ix) (0x6a + (ix)) +/* The layout of the hysteresis registers is different from the other zone + * registers. The bits for the 3 zones are stored in 2 registers: + * ZONE_HYST(0) = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0] + * ZONE_HYST(1) = [H3-3, H3-2, H3-1, H3-0, RES, RES, RES, RES] */ +#define DME1737_REG_ZONE_HYST(ix) (0x6d + (ix)) + +/* Alarm registers and bit mapping + * The 3 8-bit alarm registers will be concatenated to a single 32-bit + * alarm value [0, ALARM3, ALARM2, ALARM1]. */ +#define DME1737_REG_ALARM1 0x41 +#define DME1737_REG_ALARM2 0x42 +#define DME1737_REG_ALARM3 0x83 +static const u8 DME1737_BIT_ALARM_IN[] = {0, 1, 2, 3, 8, 16, 17}; +static const u8 DME1737_BIT_ALARM_TEMP[] = {4, 5, 6}; +static const u8 DME1737_BIT_ALARM_FAN[] = {10, 11, 12, 13, 22, 23}; + +/* Miscellaneous registers */ +#define DME1737_REG_COMPANY 0x3e +#define DME1737_REG_VERSTEP 0x3f +#define DME1737_REG_CONFIG 0x40 +#define DME1737_REG_CONFIG2 0x7f +#define DME1737_REG_VID 0x43 +#define DME1737_REG_TACH_PWM 0x81 + +/* --------------------------------------------------------------------- + * Misc defines + * --------------------------------------------------------------------- */ + +/* Chip identification */ +#define DME1737_COMPANY_SMSC 0x5c +#define DME1737_VERSTEP 0x88 +#define DME1737_VERSTEP_MASK 0xf8 + +/* --------------------------------------------------------------------- + * Data structures and manipulation thereof + * --------------------------------------------------------------------- */ + +struct dme1737_data { + struct i2c_client client; + struct class_device *class_dev; + + struct mutex update_lock; + int valid; /* !=0 if following fields are valid */ + unsigned long last_update; /* in jiffies */ + unsigned long last_vbat; /* in jiffies */ + + u8 vid; + u8 pwm_rr_en; + u8 has_pwm; + u8 has_fan; + + /* Register values */ + u16 in[7]; + u8 in_min[7]; + u8 in_max[7]; + s16 temp[3]; + s8 temp_min[3]; + s8 temp_max[3]; + s8 temp_offset[3]; + u8 config; + u8 config2; + u8 vrm; + u16 fan[6]; + u16 fan_min[6]; + u8 fan_max[2]; + u8 fan_opt[6]; + u8 pwm[6]; + u8 pwm_min[3]; + u8 pwm_config[3]; + u8 pwm_acz[3]; + u8 pwm_freq[6]; + u8 pwm_rr[2]; + u8 zone_low[3]; + u8 zone_abs[3]; + u8 zone_hyst[2]; + u32 alarms; +}; + +/* Nominal voltage values */ +static const int IN_NOMINAL[] = {5000, 2250, 3300, 5000, 12000, 3300, 3300}; + +/* Voltage input + * Voltage inputs have 16 bits resolution, limit values have 8 bits + * resolution. */ +static inline int IN_FROM_REG(int reg, int ix, int res) +{ + return (reg * IN_NOMINAL[ix] + (3 << (res - 3))) / (3 << (res - 2)); +} + +static inline int IN_TO_REG(int val, int ix) +{ + return SENSORS_LIMIT((val * 192 + IN_NOMINAL[ix] / 2) / + IN_NOMINAL[ix], 0, 255); +} + +/* Temperature input + * The register values represent temperatures in 2's complement notation from + * -127 degrees C to +127 degrees C. Temp inputs have 16 bits resolution, limit + * values have 8 bits resolution. */ +static inline int TEMP_FROM_REG(int reg, int res) +{ + return (reg * 1000) >> (res - 8); +} + +static inline int TEMP_TO_REG(int val) +{ + return SENSORS_LIMIT((val < 0 ? val - 500 : val + 500) / 1000, + -128, 127); +} + +/* Temperature range */ +static const int TEMP_RANGE[] = {2000, 2500, 3333, 4000, 5000, 6666, 8000, + 10000, 13333, 16000, 20000, 26666, 32000, + 40000, 53333, 80000}; + +static inline int TEMP_RANGE_FROM_REG(int reg) +{ + return TEMP_RANGE[(reg >> 4) & 0x0f]; +} + +static int TEMP_RANGE_TO_REG(int val, int reg) +{ + int i; + + for (i = 15; i > 0; i--) { + if (val > (TEMP_RANGE[i] + TEMP_RANGE[i - 1] + 1) / 2) { + break; + } + } + + return (reg & 0x0f) | (i << 4); +} + +/* Temperature hysteresis + * Register layout: + * reg[0] = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0] + * reg[1] = [H3-3, H3-2, H3-1, H3-0, xxxx, xxxx, xxxx, xxxx] */ +static inline int TEMP_HYST_FROM_REG(int reg, int ix) +{ + return (((ix == 1) ? reg : reg >> 4) & 0x0f) * 1000; +} + +static inline int TEMP_HYST_TO_REG(int val, int ix, int reg) +{ + int hyst = SENSORS_LIMIT((val + 500) / 1000, 0, 15); + + return (ix == 1) ? (reg & 0xf0) | hyst : (reg & 0x0f) | (hyst << 4); +} + +/* Fan input RPM */ +static inline int FAN_FROM_REG(int reg, int tpc) +{ + return (reg == 0 || reg == 0xffff) ? 0 : + (tpc == 0) ? 90000 * 60 / reg : tpc * reg; +} + +static inline int FAN_TO_REG(int val, int tpc) +{ + return SENSORS_LIMIT((tpc == 0) ? 90000 * 60 / val : val / tpc, + 0, 0xffff); +} + +/* Fan TPC (tach pulse count) + * Converts a register value to a TPC multiplier or returns 0 if the tachometer + * is configured in legacy (non-tpc) mode */ +static inline int FAN_TPC_FROM_REG(int reg) +{ + return (reg & 0x20) ? 0 : 60 >> (reg & 0x03); +} + +/* Fan type + * The type of a fan is expressed in number of pulses-per-revolution that it + * emits */ +static inline int FAN_TYPE_FROM_REG(int reg) +{ + int edge = (reg >> 1) & 0x03; + + return (edge > 0) ? 1 << (edge - 1) : 0; +} + +static inline int FAN_TYPE_TO_REG(int val, int reg) +{ + int edge = (val == 4) ? 3 : val; + + return (reg & 0xf9) | (edge << 1); +} + +/* Fan max RPM */ +static const int FAN_MAX[] = {0x54, 0x38, 0x2a, 0x21, 0x1c, 0x18, 0x15, 0x12, + 0x11, 0x0f, 0x0e}; + +static int FAN_MAX_FROM_REG(int reg) +{ + int i; + + for (i = 10; i > 0; i--) { + if (reg == FAN_MAX[i]) { + break; + } + } + + return 1000 + i * 500; +} + +static int FAN_MAX_TO_REG(int val) +{ + int i; + + for (i = 10; i > 0; i--) { + if (val > (1000 + (i - 1) * 500)) { + break; + } + } + + return FAN_MAX[i]; +} + +/* PWM enable + * Register to enable mapping: + * 000: 2 fan on zone 1 auto + * 001: 2 fan on zone 2 auto + * 010: 2 fan on zone 3 auto + * 011: 0 fan full on + * 100: -1 fan disabled + * 101: 2 fan on hottest of zones 2,3 auto + * 110: 2 fan on hottest of zones 1,2,3 auto + * 111: 1 fan in manual mode */ +static inline int PWM_EN_FROM_REG(int reg) +{ + static const int en[] = {2, 2, 2, 0, -1, 2, 2, 1}; + + return en[(reg >> 5) & 0x07]; +} + +static inline int PWM_EN_TO_REG(int val, int reg) +{ + int en = (val == 1) ? 7 : 3; + + return (reg & 0x1f) | ((en & 0x07) << 5); +} + +/* PWM auto channels zone + * Register to auto channels zone mapping (ACZ is a bitfield with bit x + * corresponding to zone x+1): + * 000: 001 fan on zone 1 auto + * 001: 010 fan on zone 2 auto + * 010: 100 fan on zone 3 auto + * 011: 000 fan full on + * 100: 000 fan disabled + * 101: 110 fan on hottest of zones 2,3 auto + * 110: 111 fan on hottest of zones 1,2,3 auto + * 111: 000 fan in manual mode */ +static inline int PWM_ACZ_FROM_REG(int reg) +{ + static const int acz[] = {1, 2, 4, 0, 0, 6, 7, 0}; + + return acz[(reg >> 5) & 0x07]; +} + +static inline int PWM_ACZ_TO_REG(int val, int reg) +{ + int acz = (val == 4) ? 2 : val - 1; + + return (reg & 0x1f) | ((acz & 0x07) << 5); +} + +/* PWM frequency */ +static const int PWM_FREQ[] = {11, 15, 22, 29, 35, 44, 59, 88, + 15000, 20000, 30000, 25000, 0, 0, 0, 0}; + +static inline int PWM_FREQ_FROM_REG(int reg) +{ + return PWM_FREQ[reg & 0x0f]; +} + +static int PWM_FREQ_TO_REG(int val, int reg) +{ + int i; + + /* the first two cases are special - stupid chip design! */ + if (val > 27500) { + i = 10; + } else if (val > 22500) { + i = 11; + } else { + for (i = 9; i > 0; i--) { + if (val > (PWM_FREQ[i] + PWM_FREQ[i - 1] + 1) / 2) { + break; + } + } + } + + return (reg & 0xf0) | i; +} + +/* PWM ramp rate + * Register layout: + * reg[0] = [OFF3, OFF2, OFF1, RES, RR1-E, RR1-2, RR1-1, RR1-0] + * reg[1] = [RR2-E, RR2-2, RR2-1, RR2-0, RR3-E, RR3-2, RR3-1, RR3-0] */ +static const u8 PWM_RR[] = {206, 104, 69, 41, 26, 18, 10, 5}; + +static inline int PWM_RR_FROM_REG(int reg, int ix) +{ + int rr = (ix == 1) ? reg >> 4 : reg; + + return (rr & 0x08) ? PWM_RR[rr & 0x07] : 0; +} + +static int PWM_RR_TO_REG(int val, int ix, int reg) +{ + int i; + + for (i = 0; i < 7; i++) { + if (val > (PWM_RR[i] + PWM_RR[i + 1] + 1) / 2) { + break; + } + } + + return (ix == 1) ? (reg & 0x8f) | (i << 4) : (reg & 0xf8) | i; +} + +/* PWM ramp rate enable */ +static inline int PWM_RR_EN_FROM_REG(int reg, int ix) +{ + return PWM_RR_FROM_REG(reg, ix) ? 1 : 0; +} + +static inline int PWM_RR_EN_TO_REG(int val, int ix, int reg) +{ + int en = (ix == 1) ? 0x80 : 0x08; + + return val ? reg | en : reg & ~en; +} + +/* PWM min/off + * The PWM min/off bits are part of the PMW ramp rate register 0 (see above for + * the register layout). */ +static inline int PWM_OFF_FROM_REG(int reg, int ix) +{ + return (reg >> (ix + 5)) & 0x01; +} + +static inline int PWM_OFF_TO_REG(int val, int ix, int reg) +{ + return (reg & ~(1 << (ix + 5))) | ((val & 0x01) << (ix + 5)); +} + +/* --------------------------------------------------------------------- + * Device I/O access + * --------------------------------------------------------------------- */ + +static u8 dme1737_read(struct i2c_client *client, u8 reg) +{ + s32 val = i2c_smbus_read_byte_data(client, reg); + + if (val < 0) { + dev_warn(&client->dev, "Read from register 0x%02x failed! " + "Please report to the driver maintainer.\n", reg); + } + + return val; +} + +static s32 dme1737_write(struct i2c_client *client, u8 reg, u8 value) +{ + s32 res = i2c_smbus_write_byte_data(client, reg, value); + + if (res < 0) { + dev_warn(&client->dev, "Write to register 0x%02x failed! " + "Please report to the driver maintainer.\n", reg); + } + + return res; +} + +static struct dme1737_data *dme1737_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + int ix; + u8 lsb[5]; + + mutex_lock(&data->update_lock); + + /* Enable a Vbat monitoring cycle every 10 mins */ + if (time_after(jiffies, data->last_vbat + 600 * HZ) || !data->valid) { + dme1737_write(client, DME1737_REG_CONFIG, dme1737_read(client, + DME1737_REG_CONFIG) | 0x10); + data->last_vbat = jiffies; + } + + /* Sample register contents every 1 sec */ + if (time_after(jiffies, data->last_update + HZ) || !data->valid) { + data->vid = dme1737_read(client, DME1737_REG_VID) & 0x3f; + + /* In (voltage) registers */ + for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) { + /* Voltage inputs are stored as 16 bit values even + * though they have only 12 bits resolution. This is + * to make it consistent with the temp inputs. */ + data->in[ix] = dme1737_read(client, + DME1737_REG_IN(ix)) << 8; + data->in_min[ix] = dme1737_read(client, + DME1737_REG_IN_MIN(ix)); + data->in_max[ix] = dme1737_read(client, + DME1737_REG_IN_MAX(ix)); + } + + /* Temp registers */ + for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) { + /* Temp inputs are stored as 16 bit values even + * though they have only 12 bits resolution. This is + * to take advantage of implicit conversions between + * register values (2's complement) and temp values + * (signed decimal). */ + data->temp[ix] = dme1737_read(client, + DME1737_REG_TEMP(ix)) << 8; + data->temp_min[ix] = dme1737_read(client, + DME1737_REG_TEMP_MIN(ix)); + data->temp_max[ix] = dme1737_read(client, + DME1737_REG_TEMP_MAX(ix)); + data->temp_offset[ix] = dme1737_read(client, + DME1737_REG_TEMP_OFFSET(ix)); + } + + /* In and temp LSB registers + * The LSBs are latched when the MSBs are read, so the order in + * which the registers are read (MSB first, then LSB) is + * important! */ + for (ix = 0; ix < ARRAY_SIZE(lsb); ix++) { + lsb[ix] = dme1737_read(client, + DME1737_REG_IN_TEMP_LSB(ix)); + } + for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) { + data->in[ix] |= (lsb[DME1737_REG_IN_LSB[ix]] << + DME1737_REG_IN_LSB_SHL[ix]) & 0xf0; + } + for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) { + data->temp[ix] |= (lsb[DME1737_REG_TEMP_LSB[ix]] << + DME1737_REG_TEMP_LSB_SHL[ix]) & 0xf0; + } + + /* Fan registers */ + for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) { + /* Skip reading registers if optional fans are not + * present */ + if (!(data->has_fan & (1 << ix))) { + continue; + } + data->fan[ix] = dme1737_read(client, + DME1737_REG_FAN(ix)); + data->fan[ix] |= dme1737_read(client, + DME1737_REG_FAN(ix) + 1) << 8; + data->fan_min[ix] = dme1737_read(client, + DME1737_REG_FAN_MIN(ix)); + data->fan_min[ix] |= dme1737_read(client, + DME1737_REG_FAN_MIN(ix) + 1) << 8; + data->fan_opt[ix] = dme1737_read(client, + DME1737_REG_FAN_OPT(ix)); + /* fan_max exists only for fan[5-6] */ + if (ix > 3) { + data->fan_max[ix - 4] = dme1737_read(client, + DME1737_REG_FAN_MAX(ix)); + } + } + + /* PWM registers */ + for (ix = 0; ix < ARRAY_SIZE(data->pwm); ix++) { + /* Skip reading registers if optional PWMs are not + * present */ + if (!(data->has_pwm & (1 << ix))) { + continue; + } + data->pwm[ix] = dme1737_read(client, + DME1737_REG_PWM(ix)); + data->pwm_freq[ix] = dme1737_read(client, + DME1737_REG_PWM_FREQ(ix)); + /* pwm_config and pwm_min exist only for pwm[1-3] */ + if (ix < 3) { + data->pwm_config[ix] = dme1737_read(client, + DME1737_REG_PWM_CONFIG(ix)); + data->pwm_min[ix] = dme1737_read(client, + DME1737_REG_PWM_MIN(ix)); + } + } + for (ix = 0; ix < ARRAY_SIZE(data->pwm_rr); ix++) { + data->pwm_rr[ix] = dme1737_read(client, + DME1737_REG_PWM_RR(ix)); + } + + /* Thermal zone registers */ + for (ix = 0; ix < ARRAY_SIZE(data->zone_low); ix++) { + data->zone_low[ix] = dme1737_read(client, + DME1737_REG_ZONE_LOW(ix)); + data->zone_abs[ix] = dme1737_read(client, + DME1737_REG_ZONE_ABS(ix)); + } + for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) { + data->zone_hyst[ix] = dme1737_read(client, + DME1737_REG_ZONE_HYST(ix)); + } + + /* Alarm registers */ + data->alarms = dme1737_read(client, + DME1737_REG_ALARM1); + /* Bit 7 tells us if the other alarm registers are non-zero and + * therefore also need to be read */ + if (data->alarms & 0x80) { + data->alarms |= dme1737_read(client, + DME1737_REG_ALARM2) << 8; + data->alarms |= dme1737_read(client, + DME1737_REG_ALARM3) << 16; + } + + data->last_update = jiffies; + data->valid = 1; + } + + mutex_unlock(&data->update_lock); + + return data; +} + +/* --------------------------------------------------------------------- + * Voltage sysfs attributes + * ix = [0-5] + * --------------------------------------------------------------------- */ + +#define SYS_IN_INPUT 0 +#define SYS_IN_MIN 1 +#define SYS_IN_MAX 2 +#define SYS_IN_ALARM 3 + +static ssize_t show_in(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + int res; + + switch (fn) { + case SYS_IN_INPUT: + res = IN_FROM_REG(data->in[ix], ix, 16); + break; + case SYS_IN_MIN: + res = IN_FROM_REG(data->in_min[ix], ix, 8); + break; + case SYS_IN_MAX: + res = IN_FROM_REG(data->in_max[ix], ix, 8); + break; + case SYS_IN_ALARM: + res = (data->alarms >> DME1737_BIT_ALARM_IN[ix]) & 0x01; + break; + default: + res = 0; + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + + return sprintf(buf, "%d\n", res); +} + +static ssize_t set_in(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + switch (fn) { + case SYS_IN_MIN: + data->in_min[ix] = IN_TO_REG(val, ix); + dme1737_write(client, DME1737_REG_IN_MIN(ix), + data->in_min[ix]); + break; + case SYS_IN_MAX: + data->in_max[ix] = IN_TO_REG(val, ix); + dme1737_write(client, DME1737_REG_IN_MAX(ix), + data->in_max[ix]); + break; + default: + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + mutex_unlock(&data->update_lock); + + return count; +} + +/* --------------------------------------------------------------------- + * Temperature sysfs attributes + * ix = [0-2] + * --------------------------------------------------------------------- */ + +#define SYS_TEMP_INPUT 0 +#define SYS_TEMP_MIN 1 +#define SYS_TEMP_MAX 2 +#define SYS_TEMP_OFFSET 3 +#define SYS_TEMP_ALARM 4 +#define SYS_TEMP_FAULT 5 + +static ssize_t show_temp(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + int res; + + switch (fn) { + case SYS_TEMP_INPUT: + res = TEMP_FROM_REG(data->temp[ix], 16); + break; + case SYS_TEMP_MIN: + res = TEMP_FROM_REG(data->temp_min[ix], 8); + break; + case SYS_TEMP_MAX: + res = TEMP_FROM_REG(data->temp_max[ix], 8); + break; + case SYS_TEMP_OFFSET: + res = TEMP_FROM_REG(data->temp_offset[ix], 8); + break; + case SYS_TEMP_ALARM: + res = (data->alarms >> DME1737_BIT_ALARM_TEMP[ix]) & 0x01; + break; + case SYS_TEMP_FAULT: + res = (data->temp[ix] == 0x0800); + break; + default: + res = 0; + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + + return sprintf(buf, "%d\n", res); +} + +static ssize_t set_temp(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + switch (fn) { + case SYS_TEMP_MIN: + data->temp_min[ix] = TEMP_TO_REG(val); + dme1737_write(client, DME1737_REG_TEMP_MIN(ix), + data->temp_min[ix]); + break; + case SYS_TEMP_MAX: + data->temp_max[ix] = TEMP_TO_REG(val); + dme1737_write(client, DME1737_REG_TEMP_MAX(ix), + data->temp_max[ix]); + break; + case SYS_TEMP_OFFSET: + data->temp_offset[ix] = TEMP_TO_REG(val); + dme1737_write(client, DME1737_REG_TEMP_OFFSET(ix), + data->temp_offset[ix]); + break; + default: + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + mutex_unlock(&data->update_lock); + + return count; +} + +/* --------------------------------------------------------------------- + * Zone sysfs attributes + * ix = [0-2] + * --------------------------------------------------------------------- */ + +#define SYS_ZONE_AUTO_CHANNELS_TEMP 0 +#define SYS_ZONE_AUTO_POINT1_TEMP_HYST 1 +#define SYS_ZONE_AUTO_POINT1_TEMP 2 +#define SYS_ZONE_AUTO_POINT2_TEMP 3 +#define SYS_ZONE_AUTO_POINT3_TEMP 4 + +static ssize_t show_zone(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + int res; + + switch (fn) { + case SYS_ZONE_AUTO_CHANNELS_TEMP: + /* check config2 for non-standard temp-to-zone mapping */ + if ((ix == 1) && (data->config2 & 0x02)) { + res = 4; + } else { + res = 1 << ix; + } + break; + case SYS_ZONE_AUTO_POINT1_TEMP_HYST: + res = TEMP_FROM_REG(data->zone_low[ix], 8) - + TEMP_HYST_FROM_REG(data->zone_hyst[ix == 2], ix); + break; + case SYS_ZONE_AUTO_POINT1_TEMP: + res = TEMP_FROM_REG(data->zone_low[ix], 8); + break; + case SYS_ZONE_AUTO_POINT2_TEMP: + /* pwm_freq holds the temp range bits in the upper nibble */ + res = TEMP_FROM_REG(data->zone_low[ix], 8) + + TEMP_RANGE_FROM_REG(data->pwm_freq[ix]); + break; + case SYS_ZONE_AUTO_POINT3_TEMP: + res = TEMP_FROM_REG(data->zone_abs[ix], 8); + break; + default: + res = 0; + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + + return sprintf(buf, "%d\n", res); +} + +static ssize_t set_zone(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + switch (fn) { + case SYS_ZONE_AUTO_POINT1_TEMP_HYST: + /* Refresh the cache */ + data->zone_low[ix] = dme1737_read(client, + DME1737_REG_ZONE_LOW(ix)); + /* Modify the temp hyst value */ + data->zone_hyst[ix == 2] = TEMP_HYST_TO_REG( + TEMP_FROM_REG(data->zone_low[ix], 8) - + val, ix, dme1737_read(client, + DME1737_REG_ZONE_HYST(ix == 2))); + dme1737_write(client, DME1737_REG_ZONE_HYST(ix == 2), + data->zone_hyst[ix == 2]); + break; + case SYS_ZONE_AUTO_POINT1_TEMP: + data->zone_low[ix] = TEMP_TO_REG(val); + dme1737_write(client, DME1737_REG_ZONE_LOW(ix), + data->zone_low[ix]); + break; + case SYS_ZONE_AUTO_POINT2_TEMP: + /* Refresh the cache */ + data->zone_low[ix] = dme1737_read(client, + DME1737_REG_ZONE_LOW(ix)); + /* Modify the temp range value (which is stored in the upper + * nibble of the pwm_freq register) */ + data->pwm_freq[ix] = TEMP_RANGE_TO_REG(val - + TEMP_FROM_REG(data->zone_low[ix], 8), + dme1737_read(client, + DME1737_REG_PWM_FREQ(ix))); + dme1737_write(client, DME1737_REG_PWM_FREQ(ix), + data->pwm_freq[ix]); + break; + case SYS_ZONE_AUTO_POINT3_TEMP: + data->zone_abs[ix] = TEMP_TO_REG(val); + dme1737_write(client, DME1737_REG_ZONE_ABS(ix), + data->zone_abs[ix]); + break; + default: + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + mutex_unlock(&data->update_lock); + + return count; +} + +/* --------------------------------------------------------------------- + * Fan sysfs attributes + * ix = [0-5] + * --------------------------------------------------------------------- */ + +#define SYS_FAN_INPUT 0 +#define SYS_FAN_MIN 1 +#define SYS_FAN_MAX 2 +#define SYS_FAN_ALARM 3 +#define SYS_FAN_TYPE 4 + +static ssize_t show_fan(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + int res; + + switch (fn) { + case SYS_FAN_INPUT: + res = FAN_FROM_REG(data->fan[ix], + ix < 4 ? 0 : + FAN_TPC_FROM_REG(data->fan_opt[ix])); + break; + case SYS_FAN_MIN: + res = FAN_FROM_REG(data->fan_min[ix], + ix < 4 ? 0 : + FAN_TPC_FROM_REG(data->fan_opt[ix])); + break; + case SYS_FAN_MAX: + /* only valid for fan[5-6] */ + res = FAN_MAX_FROM_REG(data->fan_max[ix - 4]); + break; + case SYS_FAN_ALARM: + res = (data->alarms >> DME1737_BIT_ALARM_FAN[ix]) & 0x01; + break; + case SYS_FAN_TYPE: + /* only valid for fan[1-4] */ + res = FAN_TYPE_FROM_REG(data->fan_opt[ix]); + break; + default: + res = 0; + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + + return sprintf(buf, "%d\n", res); +} + +static ssize_t set_fan(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + switch (fn) { + case SYS_FAN_MIN: + if (ix < 4) { + data->fan_min[ix] = FAN_TO_REG(val, 0); + } else { + /* Refresh the cache */ + data->fan_opt[ix] = dme1737_read(client, + DME1737_REG_FAN_OPT(ix)); + /* Modify the fan min value */ + data->fan_min[ix] = FAN_TO_REG(val, + FAN_TPC_FROM_REG(data->fan_opt[ix])); + } + dme1737_write(client, DME1737_REG_FAN_MIN(ix), + data->fan_min[ix] & 0xff); + dme1737_write(client, DME1737_REG_FAN_MIN(ix) + 1, + data->fan_min[ix] >> 8); + break; + case SYS_FAN_MAX: + /* Only valid for fan[5-6] */ + data->fan_max[ix - 4] = FAN_MAX_TO_REG(val); + dme1737_write(client, DME1737_REG_FAN_MAX(ix), + data->fan_max[ix - 4]); + break; + case SYS_FAN_TYPE: + /* Only valid for fan[1-4] */ + if (!(val == 1 || val == 2 || val == 4)) { + count = -EINVAL; + dev_warn(&client->dev, "Fan type value %ld not " + "supported. Choose one of 1, 2, or 4.\n", + val); + goto exit; + } + data->fan_opt[ix] = FAN_TYPE_TO_REG(val, dme1737_read(client, + DME1737_REG_FAN_OPT(ix))); + dme1737_write(client, DME1737_REG_FAN_OPT(ix), + data->fan_opt[ix]); + break; + default: + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } +exit: + mutex_unlock(&data->update_lock); + + return count; +} + +/* --------------------------------------------------------------------- + * PWM sysfs attributes + * ix = [0-4] + * --------------------------------------------------------------------- */ + +#define SYS_PWM 0 +#define SYS_PWM_FREQ 1 +#define SYS_PWM_ENABLE 2 +#define SYS_PWM_RAMP_RATE 3 +#define SYS_PWM_AUTO_CHANNELS_ZONE 4 +#define SYS_PWM_AUTO_PWM_MIN 5 +#define SYS_PWM_AUTO_POINT1_PWM 6 +#define SYS_PWM_AUTO_POINT2_PWM 7 + +static ssize_t show_pwm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + int res; + + switch (fn) { + case SYS_PWM: + if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 0) { + res = 255; + } else { + res = data->pwm[ix]; + } + break; + case SYS_PWM_FREQ: + res = PWM_FREQ_FROM_REG(data->pwm_freq[ix]); + break; + case SYS_PWM_ENABLE: + if (ix > 3) { + res = 1; /* pwm[5-6] hard-wired to manual mode */ + } else { + res = PWM_EN_FROM_REG(data->pwm_config[ix]); + } + break; + case SYS_PWM_RAMP_RATE: + /* Only valid for pwm[1-3] */ + res = PWM_RR_FROM_REG(data->pwm_rr[ix > 0], ix); + break; + case SYS_PWM_AUTO_CHANNELS_ZONE: + /* Only valid for pwm[1-3] */ + if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { + res = PWM_ACZ_FROM_REG(data->pwm_config[ix]); + } else { + res = data->pwm_acz[ix]; + } + break; + case SYS_PWM_AUTO_PWM_MIN: + /* Only valid for pwm[1-3] */ + if (PWM_OFF_FROM_REG(data->pwm_rr[0], ix)) { + res = data->pwm_min[ix]; + } else { + res = 0; + } + break; + case SYS_PWM_AUTO_POINT1_PWM: + /* Only valid for pwm[1-3] */ + res = data->pwm_min[ix]; + break; + case SYS_PWM_AUTO_POINT2_PWM: + /* Only valid for pwm[1-3] */ + res = 255; /* hard-wired */ + break; + default: + res = 0; + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } + + return sprintf(buf, "%d\n", res); +} + +static struct attribute *dme1737_attr_pwm[]; +static void dme1737_chmod_file(struct i2c_client*, struct attribute*, mode_t); + +static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 + *sensor_attr_2 = to_sensor_dev_attr_2(attr); + int ix = sensor_attr_2->index; + int fn = sensor_attr_2->nr; + long val = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->update_lock); + switch (fn) { + case SYS_PWM: + data->pwm[ix] = SENSORS_LIMIT(val, 0, 255); + dme1737_write(client, DME1737_REG_PWM(ix), data->pwm[ix]); + break; + case SYS_PWM_FREQ: + data->pwm_freq[ix] = PWM_FREQ_TO_REG(val, dme1737_read(client, + DME1737_REG_PWM_FREQ(ix))); + dme1737_write(client, DME1737_REG_PWM_FREQ(ix), + data->pwm_freq[ix]); + break; + case SYS_PWM_ENABLE: + /* Only valid for pwm[1-3] */ + if (val < 0 || val > 2) { + count = -EINVAL; + dev_warn(&client->dev, "PWM enable %ld not " + "supported. Choose one of 0, 1, or 2.\n", + val); + goto exit; + } + /* Refresh the cache */ + data->pwm_config[ix] = dme1737_read(client, + DME1737_REG_PWM_CONFIG(ix)); + if (val == PWM_EN_FROM_REG(data->pwm_config[ix])) { + /* Bail out if no change */ + goto exit; + } + /* Do some housekeeping if we are currently in auto mode */ + if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { + /* Save the current zone channel assignment */ + data->pwm_acz[ix] = PWM_ACZ_FROM_REG( + data->pwm_config[ix]); + /* Save the current ramp rate state and disable it */ + data->pwm_rr[ix > 0] = dme1737_read(client, + DME1737_REG_PWM_RR(ix > 0)); + data->pwm_rr_en &= ~(1 << ix); + if (PWM_RR_EN_FROM_REG(data->pwm_rr[ix > 0], ix)) { + data->pwm_rr_en |= (1 << ix); + data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(0, ix, + data->pwm_rr[ix > 0]); + dme1737_write(client, + DME1737_REG_PWM_RR(ix > 0), + data->pwm_rr[ix > 0]); + } + } + /* Set the new PWM mode */ + switch (val) { + case 0: + /* Change permissions of pwm[ix] to read-only */ + dme1737_chmod_file(client, dme1737_attr_pwm[ix], + S_IRUGO); + /* Turn fan fully on */ + data->pwm_config[ix] = PWM_EN_TO_REG(0, + data->pwm_config[ix]); + dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), + data->pwm_config[ix]); + break; + case 1: + /* Turn on manual mode */ + data->pwm_config[ix] = PWM_EN_TO_REG(1, + data->pwm_config[ix]); + dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), + data->pwm_config[ix]); + /* Change permissions of pwm[ix] to read-writeable */ + dme1737_chmod_file(client, dme1737_attr_pwm[ix], + S_IRUGO | S_IWUSR); + break; + case 2: + /* Change permissions of pwm[ix] to read-only */ + dme1737_chmod_file(client, dme1737_attr_pwm[ix], + S_IRUGO); + /* Turn on auto mode using the saved zone channel + * assignment */ + data->pwm_config[ix] = PWM_ACZ_TO_REG( + data->pwm_acz[ix], + data->pwm_config[ix]); + dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), + data->pwm_config[ix]); + /* Enable PWM ramp rate if previously enabled */ + if (data->pwm_rr_en & (1 << ix)) { + data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(1, ix, + dme1737_read(client, + DME1737_REG_PWM_RR(ix > 0))); + dme1737_write(client, + DME1737_REG_PWM_RR(ix > 0), + data->pwm_rr[ix > 0]); + } + break; + } + break; + case SYS_PWM_RAMP_RATE: + /* Only valid for pwm[1-3] */ + /* Refresh the cache */ + data->pwm_config[ix] = dme1737_read(client, + DME1737_REG_PWM_CONFIG(ix)); + data->pwm_rr[ix > 0] = dme1737_read(client, + DME1737_REG_PWM_RR(ix > 0)); + /* Set the ramp rate value */ + if (val > 0) { + data->pwm_rr[ix > 0] = PWM_RR_TO_REG(val, ix, + data->pwm_rr[ix > 0]); + } + /* Enable/disable the feature only if the associated PWM + * output is in automatic mode. */ + if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { + data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(val > 0, ix, + data->pwm_rr[ix > 0]); + } + dme1737_write(client, DME1737_REG_PWM_RR(ix > 0), + data->pwm_rr[ix > 0]); + break; + case SYS_PWM_AUTO_CHANNELS_ZONE: + /* Only valid for pwm[1-3] */ + if (!(val == 1 || val == 2 || val == 4 || + val == 6 || val == 7)) { + count = -EINVAL; + dev_warn(&client->dev, "PWM auto channels zone %ld " + "not supported. Choose one of 1, 2, 4, 6, " + "or 7.\n", val); + goto exit; + } + /* Refresh the cache */ + data->pwm_config[ix] = dme1737_read(client, + DME1737_REG_PWM_CONFIG(ix)); + if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { + /* PWM is already in auto mode so update the temp + * channel assignment */ + data->pwm_config[ix] = PWM_ACZ_TO_REG(val, + data->pwm_config[ix]); + dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), + data->pwm_config[ix]); + } else { + /* PWM is not in auto mode so we save the temp + * channel assignment for later use */ + data->pwm_acz[ix] = val; + } + break; + case SYS_PWM_AUTO_PWM_MIN: + /* Only valid for pwm[1-3] */ + /* Refresh the cache */ + data->pwm_min[ix] = dme1737_read(client, + DME1737_REG_PWM_MIN(ix)); + /* There are only 2 values supported for the auto_pwm_min + * value: 0 or auto_point1_pwm. So if the temperature drops + * below the auto_point1_temp_hyst value, the fan either turns + * off or runs at auto_point1_pwm duty-cycle. */ + if (val > ((data->pwm_min[ix] + 1) / 2)) { + data->pwm_rr[0] = PWM_OFF_TO_REG(1, ix, + dme1737_read(client, + DME1737_REG_PWM_RR(0))); + + } else { + data->pwm_rr[0] = PWM_OFF_TO_REG(0, ix, + dme1737_read(client, + DME1737_REG_PWM_RR(0))); + + } + dme1737_write(client, DME1737_REG_PWM_RR(0), + data->pwm_rr[0]); + break; + case SYS_PWM_AUTO_POINT1_PWM: + /* Only valid for pwm[1-3] */ + data->pwm_min[ix] = SENSORS_LIMIT(val, 0, 255); + dme1737_write(client, DME1737_REG_PWM_MIN(ix), + data->pwm_min[ix]); + break; + default: + dev_dbg(dev, "Unknown attr fetch (%d)\n", fn); + } +exit: + mutex_unlock(&data->update_lock); + + return count; +} + +/* --------------------------------------------------------------------- + * Miscellaneous sysfs attributes + * --------------------------------------------------------------------- */ + +static ssize_t show_vrm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + + return sprintf(buf, "%d\n", data->vrm); +} + +static ssize_t set_vrm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct dme1737_data *data = i2c_get_clientdata(client); + long val = simple_strtol(buf, NULL, 10); + + data->vrm = val; + return count; +} + +static ssize_t show_vid(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct dme1737_data *data = dme1737_update_device(dev); + + return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm)); +} + +/* --------------------------------------------------------------------- + * Sysfs device attribute defines and structs + * --------------------------------------------------------------------- */ + +/* Voltages 0-6 */ + +#define SENSOR_DEVICE_ATTR_IN(ix) \ +static SENSOR_DEVICE_ATTR_2(in##ix##_input, S_IRUGO, \ + show_in, NULL, SYS_IN_INPUT, ix); \ +static SENSOR_DEVICE_ATTR_2(in##ix##_min, S_IRUGO | S_IWUSR, \ + show_in, set_in, SYS_IN_MIN, ix); \ +static SENSOR_DEVICE_ATTR_2(in##ix##_max, S_IRUGO | S_IWUSR, \ + show_in, set_in, SYS_IN_MAX, ix); \ +static SENSOR_DEVICE_ATTR_2(in##ix##_alarm, S_IRUGO, \ + show_in, NULL, SYS_IN_ALARM, ix) + +SENSOR_DEVICE_ATTR_IN(0); +SENSOR_DEVICE_ATTR_IN(1); +SENSOR_DEVICE_ATTR_IN(2); +SENSOR_DEVICE_ATTR_IN(3); +SENSOR_DEVICE_ATTR_IN(4); +SENSOR_DEVICE_ATTR_IN(5); +SENSOR_DEVICE_ATTR_IN(6); + +/* Temperatures 1-3 */ + +#define SENSOR_DEVICE_ATTR_TEMP(ix) \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_input, S_IRUGO, \ + show_temp, NULL, SYS_TEMP_INPUT, ix-1); \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_min, S_IRUGO | S_IWUSR, \ + show_temp, set_temp, SYS_TEMP_MIN, ix-1); \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_max, S_IRUGO | S_IWUSR, \ + show_temp, set_temp, SYS_TEMP_MAX, ix-1); \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_offset, S_IRUGO, \ + show_temp, set_temp, SYS_TEMP_OFFSET, ix-1); \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_alarm, S_IRUGO, \ + show_temp, NULL, SYS_TEMP_ALARM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(temp##ix##_fault, S_IRUGO, \ + show_temp, NULL, SYS_TEMP_FAULT, ix-1) + +SENSOR_DEVICE_ATTR_TEMP(1); +SENSOR_DEVICE_ATTR_TEMP(2); +SENSOR_DEVICE_ATTR_TEMP(3); + +/* Zones 1-3 */ + +#define SENSOR_DEVICE_ATTR_ZONE(ix) \ +static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_channels_temp, S_IRUGO, \ + show_zone, NULL, SYS_ZONE_AUTO_CHANNELS_TEMP, ix-1); \ +static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp_hyst, S_IRUGO, \ + show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP_HYST, ix-1); \ +static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp, S_IRUGO, \ + show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP, ix-1); \ +static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point2_temp, S_IRUGO, \ + show_zone, set_zone, SYS_ZONE_AUTO_POINT2_TEMP, ix-1); \ +static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point3_temp, S_IRUGO, \ + show_zone, set_zone, SYS_ZONE_AUTO_POINT3_TEMP, ix-1) + +SENSOR_DEVICE_ATTR_ZONE(1); +SENSOR_DEVICE_ATTR_ZONE(2); +SENSOR_DEVICE_ATTR_ZONE(3); + +/* Fans 1-4 */ + +#define SENSOR_DEVICE_ATTR_FAN_1TO4(ix) \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \ + show_fan, NULL, SYS_FAN_INPUT, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \ + show_fan, set_fan, SYS_FAN_MIN, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \ + show_fan, NULL, SYS_FAN_ALARM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_type, S_IRUGO | S_IWUSR, \ + show_fan, set_fan, SYS_FAN_TYPE, ix-1) + +SENSOR_DEVICE_ATTR_FAN_1TO4(1); +SENSOR_DEVICE_ATTR_FAN_1TO4(2); +SENSOR_DEVICE_ATTR_FAN_1TO4(3); +SENSOR_DEVICE_ATTR_FAN_1TO4(4); + +/* Fans 5-6 */ + +#define SENSOR_DEVICE_ATTR_FAN_5TO6(ix) \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \ + show_fan, NULL, SYS_FAN_INPUT, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \ + show_fan, set_fan, SYS_FAN_MIN, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \ + show_fan, NULL, SYS_FAN_ALARM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(fan##ix##_max, S_IRUGO | S_IWUSR, \ + show_fan, set_fan, SYS_FAN_MAX, ix-1) + +SENSOR_DEVICE_ATTR_FAN_5TO6(5); +SENSOR_DEVICE_ATTR_FAN_5TO6(6); + +/* PWMs 1-3 */ + +#define SENSOR_DEVICE_ATTR_PWM_1TO3(ix) \ +static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_ENABLE, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_ramp_rate, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_RAMP_RATE, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_channels_zone, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_AUTO_CHANNELS_ZONE, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_pwm_min, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_AUTO_PWM_MIN, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point1_pwm, S_IRUGO, \ + show_pwm, set_pwm, SYS_PWM_AUTO_POINT1_PWM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point2_pwm, S_IRUGO, \ + show_pwm, NULL, SYS_PWM_AUTO_POINT2_PWM, ix-1) + +SENSOR_DEVICE_ATTR_PWM_1TO3(1); +SENSOR_DEVICE_ATTR_PWM_1TO3(2); +SENSOR_DEVICE_ATTR_PWM_1TO3(3); + +/* PWMs 5-6 */ + +#define SENSOR_DEVICE_ATTR_PWM_5TO6(ix) \ +static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO | S_IWUSR, \ + show_pwm, set_pwm, SYS_PWM, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \ + show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \ +static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \ + show_pwm, NULL, SYS_PWM_ENABLE, ix-1) + +SENSOR_DEVICE_ATTR_PWM_5TO6(5); +SENSOR_DEVICE_ATTR_PWM_5TO6(6); + +/* Misc */ + +static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm); +static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL); + +#define SENSOR_DEV_ATTR_IN(ix) \ +&sensor_dev_attr_in##ix##_input.dev_attr.attr, \ +&sensor_dev_attr_in##ix##_min.dev_attr.attr, \ +&sensor_dev_attr_in##ix##_max.dev_attr.attr, \ +&sensor_dev_attr_in##ix##_alarm.dev_attr.attr + +/* These attributes are read-writeable only if the chip is *not* locked */ +#define SENSOR_DEV_ATTR_TEMP_LOCK(ix) \ +&sensor_dev_attr_temp##ix##_offset.dev_attr.attr + +#define SENSOR_DEV_ATTR_TEMP(ix) \ +SENSOR_DEV_ATTR_TEMP_LOCK(ix), \ +&sensor_dev_attr_temp##ix##_input.dev_attr.attr, \ +&sensor_dev_attr_temp##ix##_min.dev_attr.attr, \ +&sensor_dev_attr_temp##ix##_max.dev_attr.attr, \ +&sensor_dev_attr_temp##ix##_alarm.dev_attr.attr, \ +&sensor_dev_attr_temp##ix##_fault.dev_attr.attr + +/* These attributes are read-writeable only if the chip is *not* locked */ +#define SENSOR_DEV_ATTR_ZONE_LOCK(ix) \ +&sensor_dev_attr_zone##ix##_auto_point1_temp_hyst.dev_attr.attr, \ +&sensor_dev_attr_zone##ix##_auto_point1_temp.dev_attr.attr, \ +&sensor_dev_attr_zone##ix##_auto_point2_temp.dev_attr.attr, \ +&sensor_dev_attr_zone##ix##_auto_point3_temp.dev_attr.attr + +#define SENSOR_DEV_ATTR_ZONE(ix) \ +SENSOR_DEV_ATTR_ZONE_LOCK(ix), \ +&sensor_dev_attr_zone##ix##_auto_channels_temp.dev_attr.attr + +#define SENSOR_DEV_ATTR_FAN_1TO4(ix) \ +&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_type.dev_attr.attr + +#define SENSOR_DEV_ATTR_FAN_5TO6(ix) \ +&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \ +&sensor_dev_attr_fan##ix##_max.dev_attr.attr + +/* These attributes are read-writeable only if the chip is *not* locked */ +#define SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix) \ +&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_ramp_rate.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_auto_channels_zone.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_auto_pwm_min.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_auto_point1_pwm.dev_attr.attr + +#define SENSOR_DEV_ATTR_PWM_1TO3(ix) \ +SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix), \ +&sensor_dev_attr_pwm##ix.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_auto_point2_pwm.dev_attr.attr + +/* These attributes are read-writeable only if the chip is *not* locked */ +#define SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix) \ +&sensor_dev_attr_pwm##ix.dev_attr.attr, \ +&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr + +#define SENSOR_DEV_ATTR_PWM_5TO6(ix) \ +SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix), \ +&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr + +/* This struct holds all the attributes that are always present and need to be + * created unconditionally. The attributes that need modification of their + * permissions are created read-only and write permissions are added or removed + * on the fly when required */ +static struct attribute *dme1737_attr[] ={ + /* Voltages */ + SENSOR_DEV_ATTR_IN(0), + SENSOR_DEV_ATTR_IN(1), + SENSOR_DEV_ATTR_IN(2), + SENSOR_DEV_ATTR_IN(3), + SENSOR_DEV_ATTR_IN(4), + SENSOR_DEV_ATTR_IN(5), + SENSOR_DEV_ATTR_IN(6), + /* Temperatures */ + SENSOR_DEV_ATTR_TEMP(1), + SENSOR_DEV_ATTR_TEMP(2), + SENSOR_DEV_ATTR_TEMP(3), + /* Zones */ + SENSOR_DEV_ATTR_ZONE(1), + SENSOR_DEV_ATTR_ZONE(2), + SENSOR_DEV_ATTR_ZONE(3), + /* Misc */ + &dev_attr_vrm.attr, + &dev_attr_cpu0_vid.attr, + NULL +}; + +static const struct attribute_group dme1737_group = { + .attrs = dme1737_attr, +}; + +/* The following structs hold the PWM attributes, some of which are optional. + * Their creation depends on the chip configuration which is determined during + * module load. */ +static struct attribute *dme1737_attr_pwm1[] = { + SENSOR_DEV_ATTR_PWM_1TO3(1), + NULL +}; +static struct attribute *dme1737_attr_pwm2[] = { + SENSOR_DEV_ATTR_PWM_1TO3(2), + NULL +}; +static struct attribute *dme1737_attr_pwm3[] = { + SENSOR_DEV_ATTR_PWM_1TO3(3), + NULL +}; +static struct attribute *dme1737_attr_pwm5[] = { + SENSOR_DEV_ATTR_PWM_5TO6(5), + NULL +}; +static struct attribute *dme1737_attr_pwm6[] = { + SENSOR_DEV_ATTR_PWM_5TO6(6), + NULL +}; + +static const struct attribute_group dme1737_pwm_group[] = { + { .attrs = dme1737_attr_pwm1 }, + { .attrs = dme1737_attr_pwm2 }, + { .attrs = dme1737_attr_pwm3 }, + { .attrs = NULL }, + { .attrs = dme1737_attr_pwm5 }, + { .attrs = dme1737_attr_pwm6 }, +}; + +/* The following structs hold the fan attributes, some of which are optional. + * Their creation depends on the chip configuration which is determined during + * module load. */ +static struct attribute *dme1737_attr_fan1[] = { + SENSOR_DEV_ATTR_FAN_1TO4(1), + NULL +}; +static struct attribute *dme1737_attr_fan2[] = { + SENSOR_DEV_ATTR_FAN_1TO4(2), + NULL +}; +static struct attribute *dme1737_attr_fan3[] = { + SENSOR_DEV_ATTR_FAN_1TO4(3), + NULL +}; +static struct attribute *dme1737_attr_fan4[] = { + SENSOR_DEV_ATTR_FAN_1TO4(4), + NULL +}; +static struct attribute *dme1737_attr_fan5[] = { + SENSOR_DEV_ATTR_FAN_5TO6(5), + NULL +}; +static struct attribute *dme1737_attr_fan6[] = { + SENSOR_DEV_ATTR_FAN_5TO6(6), + NULL +}; + +static const struct attribute_group dme1737_fan_group[] = { + { .attrs = dme1737_attr_fan1 }, + { .attrs = dme1737_attr_fan2 }, + { .attrs = dme1737_attr_fan3 }, + { .attrs = dme1737_attr_fan4 }, + { .attrs = dme1737_attr_fan5 }, + { .attrs = dme1737_attr_fan6 }, +}; + +/* The permissions of all of the following attributes are changed to read- + * writeable if the chip is *not* locked. Otherwise they stay read-only. */ +static struct attribute *dme1737_attr_lock[] = { + /* Temperatures */ + SENSOR_DEV_ATTR_TEMP_LOCK(1), + SENSOR_DEV_ATTR_TEMP_LOCK(2), + SENSOR_DEV_ATTR_TEMP_LOCK(3), + /* Zones */ + SENSOR_DEV_ATTR_ZONE_LOCK(1), + SENSOR_DEV_ATTR_ZONE_LOCK(2), + SENSOR_DEV_ATTR_ZONE_LOCK(3), + NULL +}; + +static const struct attribute_group dme1737_lock_group = { + .attrs = dme1737_attr_lock, +}; + +/* The permissions of the following PWM attributes are changed to read- + * writeable if the chip is *not* locked and the respective PWM is available. + * Otherwise they stay read-only. */ +static struct attribute *dme1737_attr_pwm1_lock[] = { + SENSOR_DEV_ATTR_PWM_1TO3_LOCK(1), + NULL +}; +static struct attribute *dme1737_attr_pwm2_lock[] = { + SENSOR_DEV_ATTR_PWM_1TO3_LOCK(2), + NULL +}; +static struct attribute *dme1737_attr_pwm3_lock[] = { + SENSOR_DEV_ATTR_PWM_1TO3_LOCK(3), + NULL +}; +static struct attribute *dme1737_attr_pwm5_lock[] = { + SENSOR_DEV_ATTR_PWM_5TO6_LOCK(5), + NULL +}; +static struct attribute *dme1737_attr_pwm6_lock[] = { + SENSOR_DEV_ATTR_PWM_5TO6_LOCK(6), + NULL +}; + +static const struct attribute_group dme1737_pwm_lock_group[] = { + { .attrs = dme1737_attr_pwm1_lock }, + { .attrs = dme1737_attr_pwm2_lock }, + { .attrs = dme1737_attr_pwm3_lock }, + { .attrs = NULL }, + { .attrs = dme1737_attr_pwm5_lock }, + { .attrs = dme1737_attr_pwm6_lock }, +}; + +/* Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the + * chip is not locked. Otherwise they are read-only. */ +static struct attribute *dme1737_attr_pwm[] = { + &sensor_dev_attr_pwm1.dev_attr.attr, + &sensor_dev_attr_pwm2.dev_attr.attr, + &sensor_dev_attr_pwm3.dev_attr.attr, +}; + +/* --------------------------------------------------------------------- + * Super-IO functions + * --------------------------------------------------------------------- */ + +static inline int dme1737_sio_inb(int sio_cip, int reg) +{ + outb(reg, sio_cip); + return inb(sio_cip + 1); +} + +static inline void dme1737_sio_outb(int sio_cip, int reg, int val) +{ + outb(reg, sio_cip); + outb(val, sio_cip + 1); +} + +static int dme1737_sio_get_features(int sio_cip, struct i2c_client *client) +{ + struct dme1737_data *data = i2c_get_clientdata(client); + int err = 0, reg; + u16 addr; + + /* Enter configuration mode */ + outb(0x55, sio_cip); + + /* Check device ID + * The DME1737 can return either 0x78 or 0x77 as its device ID. */ + reg = dme1737_sio_inb(sio_cip, 0x20); + if (!(reg == 0x77 || reg == 0x78)) { + err = -ENODEV; + goto exit; + } + + /* Select logical device A (runtime registers) */ + dme1737_sio_outb(sio_cip, 0x07, 0x0a); + + /* Get the base address of the runtime registers */ + if (!(addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) | + dme1737_sio_inb(sio_cip, 0x61))) { + err = -ENODEV; + goto exit; + } + + /* Read the runtime registers to determine which optional features + * are enabled and available. Bits [3:2] of registers 0x43-0x46 are set + * to '10' if the respective feature is enabled. */ + if ((inb(addr + 0x43) & 0x0c) == 0x08) { /* fan6 */ + data->has_fan |= (1 << 5); + } + if ((inb(addr + 0x44) & 0x0c) == 0x08) { /* pwm6 */ + data->has_pwm |= (1 << 5); + } + if ((inb(addr + 0x45) & 0x0c) == 0x08) { /* fan5 */ + data->has_fan |= (1 << 4); + } + if ((inb(addr + 0x46) & 0x0c) == 0x08) { /* pwm5 */ + data->has_pwm |= (1 << 4); + } + +exit: + /* Exit configuration mode */ + outb(0xaa, sio_cip); + + return err; +} + +/* --------------------------------------------------------------------- + * Device detection, registration and initialization + * --------------------------------------------------------------------- */ + +static struct i2c_driver dme1737_driver; + +static void dme1737_chmod_file(struct i2c_client *client, + struct attribute *attr, mode_t mode) +{ + if (sysfs_chmod_file(&client->dev.kobj, attr, mode)) { + dev_warn(&client->dev, "Failed to change permissions of %s.\n", + attr->name); + } +} + +static void dme1737_chmod_group(struct i2c_client *client, + const struct attribute_group *group, + mode_t mode) +{ + struct attribute **attr; + + for (attr = group->attrs; *attr; attr++) { + dme1737_chmod_file(client, *attr, mode); + } +} + +static int dme1737_init_client(struct i2c_client *client) +{ + struct dme1737_data *data = i2c_get_clientdata(client); + int ix; + u8 reg; + + data->config = dme1737_read(client, DME1737_REG_CONFIG); + /* Inform if part is not monitoring/started */ + if (!(data->config & 0x01)) { + if (!force_start) { + dev_err(&client->dev, "Device is not monitoring. " + "Use the force_start load parameter to " + "override.\n"); + return -EFAULT; + } + + /* Force monitoring */ + data->config |= 0x01; + dme1737_write(client, DME1737_REG_CONFIG, data->config); + } + /* Inform if part is not ready */ + if (!(data->config & 0x04)) { + dev_err(&client->dev, "Device is not ready.\n"); + return -EFAULT; + } + + data->config2 = dme1737_read(client, DME1737_REG_CONFIG2); + /* Check if optional fan3 input is enabled */ + if (data->config2 & 0x04) { + data->has_fan |= (1 << 2); + } + + /* Fan4 and pwm3 are only available if the client's I2C address + * is the default 0x2e. Otherwise the I/Os associated with these + * functions are used for addr enable/select. */ + if (client->addr == 0x2e) { + data->has_fan |= (1 << 3); + data->has_pwm |= (1 << 2); + } + + /* Determine if the optional fan[5-6] and/or pwm[5-6] are enabled. + * For this, we need to query the runtime registers through the + * Super-IO LPC interface. Try both config ports 0x2e and 0x4e. */ + if (dme1737_sio_get_features(0x2e, client) && + dme1737_sio_get_features(0x4e, client)) { + dev_warn(&client->dev, "Failed to query Super-IO for optional " + "features.\n"); + } + + /* Fan1, fan2, pwm1, and pwm2 are always present */ + data->has_fan |= 0x03; + data->has_pwm |= 0x03; + + dev_info(&client->dev, "Optional features: pwm3=%s, pwm5=%s, pwm6=%s, " + "fan3=%s, fan4=%s, fan5=%s, fan6=%s.\n", + (data->has_pwm & (1 << 2)) ? "yes" : "no", + (data->has_pwm & (1 << 4)) ? "yes" : "no", + (data->has_pwm & (1 << 5)) ? "yes" : "no", + (data->has_fan & (1 << 2)) ? "yes" : "no", + (data->has_fan & (1 << 3)) ? "yes" : "no", + (data->has_fan & (1 << 4)) ? "yes" : "no", + (data->has_fan & (1 << 5)) ? "yes" : "no"); + + reg = dme1737_read(client, DME1737_REG_TACH_PWM); + /* Inform if fan-to-pwm mapping differs from the default */ + if (reg != 0xa4) { + dev_warn(&client->dev, "Non-standard fan to pwm mapping: " + "fan1->pwm%d, fan2->pwm%d, fan3->pwm%d, " + "fan4->pwm%d. Please report to the driver " + "maintainer.\n", + (reg & 0x03) + 1, ((reg >> 2) & 0x03) + 1, + ((reg >> 4) & 0x03) + 1, ((reg >> 6) & 0x03) + 1); + } + + /* Switch pwm[1-3] to manual mode if they are currently disabled and + * set the duty-cycles to 0% (which is identical to the PWMs being + * disabled). */ + if (!(data->config & 0x02)) { + for (ix = 0; ix < 3; ix++) { + data->pwm_config[ix] = dme1737_read(client, + DME1737_REG_PWM_CONFIG(ix)); + if ((data->has_pwm & (1 << ix)) && + (PWM_EN_FROM_REG(data->pwm_config[ix]) == -1)) { + dev_info(&client->dev, "Switching pwm%d to " + "manual mode.\n", ix + 1); + data->pwm_config[ix] = PWM_EN_TO_REG(1, + data->pwm_config[ix]); + dme1737_write(client, DME1737_REG_PWM(ix), 0); + dme1737_write(client, + DME1737_REG_PWM_CONFIG(ix), + data->pwm_config[ix]); + } + } + } + + /* Initialize the default PWM auto channels zone (acz) assignments */ + data->pwm_acz[0] = 1; /* pwm1 -> zone1 */ + data->pwm_acz[1] = 2; /* pwm2 -> zone2 */ + data->pwm_acz[2] = 4; /* pwm3 -> zone3 */ + + /* Set VRM */ + data->vrm = vid_which_vrm(); + + return 0; +} + +static int dme1737_detect(struct i2c_adapter *adapter, int address, + int kind) +{ + u8 company, verstep = 0; + struct i2c_client *client; + struct dme1737_data *data; + int ix, err = 0; + const char *name; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { + goto exit; + } + + if (!(data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL))) { + err = -ENOMEM; + goto exit; + } + + client = &data->client; + i2c_set_clientdata(client, data); + client->addr = address; + client->adapter = adapter; + client->driver = &dme1737_driver; + + /* A negative kind means that the driver was loaded with no force + * parameter (default), so we must identify the chip. */ + if (kind < 0) { + company = dme1737_read(client, DME1737_REG_COMPANY); + verstep = dme1737_read(client, DME1737_REG_VERSTEP); + + if (!((company == DME1737_COMPANY_SMSC) && + ((verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP))) { + err = -ENODEV; + goto exit_kfree; + } + } + + kind = dme1737; + name = "dme1737"; + + /* Fill in the remaining client fields and put it into the global + * list */ + strlcpy(client->name, name, I2C_NAME_SIZE); + mutex_init(&data->update_lock); + + /* Tell the I2C layer a new client has arrived */ + if ((err = i2c_attach_client(client))) { + goto exit_kfree; + } + + /* Initialize the DME1737 chip */ + if ((err = dme1737_init_client(client))) { + goto exit_detach; + } + + /* Create standard sysfs attributes */ + if ((err = sysfs_create_group(&client->dev.kobj, &dme1737_group))) { + goto exit_detach; + } + + /* Create fan sysfs attributes */ + for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { + if (data->has_fan & (1 << ix)) { + if ((err = sysfs_create_group(&client->dev.kobj, + &dme1737_fan_group[ix]))) { + goto exit_remove; + } + } + } + + /* Create PWM sysfs attributes */ + for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) { + if (data->has_pwm & (1 << ix)) { + if ((err = sysfs_create_group(&client->dev.kobj, + &dme1737_pwm_group[ix]))) { + goto exit_remove; + } + } + } + + /* Inform if the device is locked. Otherwise change the permissions of + * selected attributes from read-only to read-writeable. */ + if (data->config & 0x02) { + dev_info(&client->dev, "Device is locked. Some attributes " + "will be read-only.\n"); + } else { + /* Change permissions of standard attributes */ + dme1737_chmod_group(client, &dme1737_lock_group, + S_IRUGO | S_IWUSR); + + /* Change permissions of PWM attributes */ + for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_lock_group); ix++) { + if (data->has_pwm & (1 << ix)) { + dme1737_chmod_group(client, + &dme1737_pwm_lock_group[ix], + S_IRUGO | S_IWUSR); + } + } + + /* Change permissions of pwm[1-3] if in manual mode */ + for (ix = 0; ix < 3; ix++) { + if ((data->has_pwm & (1 << ix)) && + (PWM_EN_FROM_REG(data->pwm_config[ix]) == 1)) { + dme1737_chmod_file(client, + dme1737_attr_pwm[ix], + S_IRUGO | S_IWUSR); + } + } + } + + /* Register device */ + data->class_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->class_dev)) { + err = PTR_ERR(data->class_dev); + goto exit_remove; + } + + dev_info(&adapter->dev, "Found a DME1737 chip at 0x%02x " + "(rev 0x%02x)\n", client->addr, verstep); + + return 0; + +exit_remove: + for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { + if (data->has_fan & (1 << ix)) { + sysfs_remove_group(&client->dev.kobj, + &dme1737_fan_group[ix]); + } + } + for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) { + if (data->has_pwm & (1 << ix)) { + sysfs_remove_group(&client->dev.kobj, + &dme1737_pwm_group[ix]); + } + } + sysfs_remove_group(&client->dev.kobj, &dme1737_group); +exit_detach: + i2c_detach_client(client); +exit_kfree: + kfree(data); +exit: + return err; +} + +static int dme1737_attach_adapter(struct i2c_adapter *adapter) +{ + if (!(adapter->class & I2C_CLASS_HWMON)) { + return 0; + } + + return i2c_probe(adapter, &addr_data, dme1737_detect); +} + +static int dme1737_detach_client(struct i2c_client *client) +{ + struct dme1737_data *data = i2c_get_clientdata(client); + int ix, err; + + hwmon_device_unregister(data->class_dev); + + for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { + if (data->has_fan & (1 << ix)) { + sysfs_remove_group(&client->dev.kobj, + &dme1737_fan_group[ix]); + } + } + for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) { + if (data->has_pwm & (1 << ix)) { + sysfs_remove_group(&client->dev.kobj, + &dme1737_pwm_group[ix]); + } + } + sysfs_remove_group(&client->dev.kobj, &dme1737_group); + + if ((err = i2c_detach_client(client))) { + return err; + } + + kfree(data); + return 0; +} + +static struct i2c_driver dme1737_driver = { + .driver = { + .name = "dme1737", + }, + .attach_adapter = dme1737_attach_adapter, + .detach_client = dme1737_detach_client, +}; + +static int __init dme1737_init(void) +{ + return i2c_add_driver(&dme1737_driver); +} + +static void __exit dme1737_exit(void) +{ + i2c_del_driver(&dme1737_driver); +} + +MODULE_AUTHOR("Juerg Haefliger <juergh@gmail.com>"); +MODULE_DESCRIPTION("DME1737 sensors"); +MODULE_LICENSE("GPL"); + +module_init(dme1737_init); +module_exit(dme1737_exit); |