Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull x86 platform changes from Ingo Molnar.

Removes the Moorestown platform that nobody ever used.

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/platform: Move APIC ID validity check into platform APIC code
  x86/olpc/xo15/sci: Enable lid close wakeup control
  x86/geode/net5501: Add platform driver for Soekris Engineering net5501
  x86/geode/alix2: Supplement driver to include GPIO button support
  x86/mid/powerbtn: Use MSIC read/write instead of ipc_scu
  x86/mid/thermal: Turn off thermistor
  x86/mid/thermal: Add msic_thermal alias
  x86/mid/thermal: Convert to use Intel MSIC API
  x86/mid/scu_ipc: Remove Moorestown support
  x86/mid: Kill off Moorestown
  x86/mrst: Add msic_thermal platform support
  x86/config: Select MSIC MFD driver on Intel Medfield platform
  x86/mid: Remove Intel Moorestown
  x86/mrst: Set ISA bus type for fake MP IRQs
  x86/ioapic: Use legacy_pic to set correct gsi-irq mapping

7 files changed, 82 insertions, 931 deletions

diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 15dbd8c..2dc02c9 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -696,33 +696,11 @@ config INTEL_MID_POWER_BUTTON
 
 config INTEL_MFLD_THERMAL
        tristate "Thermal driver for Intel Medfield platform"
-       depends on INTEL_SCU_IPC && THERMAL
+       depends on MFD_INTEL_MSIC && THERMAL
        help
          Say Y here to enable thermal driver support for the  Intel Medfield
          platform.
 
-config RAR_REGISTER
-	bool "Restricted Access Region Register Driver"
-	depends on PCI && X86_MRST
-	default n
-	---help---
-	  This driver allows other kernel drivers access to the
-	  contents of the restricted access region control registers.
-
-	  The restricted access region control registers
-	  (rar_registers) are used to pass address and
-	  locking information on restricted access regions
-	  to other drivers that use restricted access regions.
-
-	  The restricted access regions are regions of memory
-	  on the Intel MID Platform that are not accessible to
-	  the x86 processor, but are accessible to dedicated
-	  processors on board peripheral devices.
-
-	  The purpose of the restricted access regions is to
-	  protect sensitive data from compromise by unauthorized
-	  programs running on the x86 processor.
-
 config INTEL_IPS
 	tristate "Intel Intelligent Power Sharing"
 	depends on ACPI
diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
index d328f21..bb94765 100644
--- a/drivers/platform/x86/Makefile
+++ b/drivers/platform/x86/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_TOSHIBA_BT_RFKILL)	+= toshiba_bluetooth.o
 obj-$(CONFIG_INTEL_SCU_IPC)	+= intel_scu_ipc.o
 obj-$(CONFIG_INTEL_SCU_IPC_UTIL) += intel_scu_ipcutil.o
 obj-$(CONFIG_INTEL_MFLD_THERMAL) += intel_mid_thermal.o
-obj-$(CONFIG_RAR_REGISTER)	+= intel_rar_register.o
 obj-$(CONFIG_INTEL_IPS)		+= intel_ips.o
 obj-$(CONFIG_GPIO_INTEL_PMIC)	+= intel_pmic_gpio.o
 obj-$(CONFIG_XO1_RFKILL)	+= xo1-rfkill.o
diff --git a/drivers/platform/x86/intel_mid_powerbtn.c b/drivers/platform/x86/intel_mid_powerbtn.c
index f1ae507..0903a88 100644
--- a/drivers/platform/x86/intel_mid_powerbtn.c
+++ b/drivers/platform/x86/intel_mid_powerbtn.c
@@ -23,21 +23,27 @@
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/input.h>
-
-#include <asm/intel_scu_ipc.h>
+#include <linux/mfd/intel_msic.h>
 
 #define DRIVER_NAME "msic_power_btn"
 
-#define MSIC_PB_STATUS	0x3f
 #define MSIC_PB_LEVEL	(1 << 3) /* 1 - release, 0 - press */
 
+/*
+ * MSIC document ti_datasheet defines the 1st bit reg 0x21 is used to mask
+ * power button interrupt
+ */
+#define MSIC_PWRBTNM    (1 << 0)
+
 static irqreturn_t mfld_pb_isr(int irq, void *dev_id)
 {
 	struct input_dev *input = dev_id;
 	int ret;
 	u8 pbstat;
 
-	ret = intel_scu_ipc_ioread8(MSIC_PB_STATUS, &pbstat);
+	ret = intel_msic_reg_read(INTEL_MSIC_PBSTATUS, &pbstat);
+	dev_dbg(input->dev.parent, "PB_INT status= %d\n", pbstat);
+
 	if (ret < 0) {
 		dev_err(input->dev.parent, "Read error %d while reading"
 			       " MSIC_PB_STATUS\n", ret);
@@ -88,6 +94,24 @@ static int __devinit mfld_pb_probe(struct platform_device *pdev)
 	}
 
 	platform_set_drvdata(pdev, input);
+
+	/*
+	 * SCU firmware might send power button interrupts to IA core before
+	 * kernel boots and doesn't get EOI from IA core. The first bit of
+	 * MSIC reg 0x21 is kept masked, and SCU firmware doesn't send new
+	 * power interrupt to Android kernel. Unmask the bit when probing
+	 * power button in kernel.
+	 * There is a very narrow race between irq handler and power button
+	 * initialization. The race happens rarely. So we needn't worry
+	 * about it.
+	 */
+	error = intel_msic_reg_update(INTEL_MSIC_IRQLVL1MSK, 0, MSIC_PWRBTNM);
+	if (error) {
+		dev_err(&pdev->dev, "Unable to clear power button interrupt, "
+				"error: %d\n", error);
+		goto err_free_irq;
+	}
+
 	return 0;
 
 err_free_irq:
diff --git a/drivers/platform/x86/intel_mid_thermal.c b/drivers/platform/x86/intel_mid_thermal.c
index ccd7b1f..2ee9766 100644
--- a/drivers/platform/x86/intel_mid_thermal.c
+++ b/drivers/platform/x86/intel_mid_thermal.c
@@ -33,18 +33,15 @@
 #include <linux/slab.h>
 #include <linux/pm.h>
 #include <linux/thermal.h>
-
-#include <asm/intel_scu_ipc.h>
+#include <linux/mfd/intel_msic.h>
 
 /* Number of thermal sensors */
 #define MSIC_THERMAL_SENSORS	4
 
 /* ADC1 - thermal registers */
-#define MSIC_THERM_ADC1CNTL1	0x1C0
 #define MSIC_ADC_ENBL		0x10
 #define MSIC_ADC_START		0x08
 
-#define MSIC_THERM_ADC1CNTL3	0x1C2
 #define MSIC_ADCTHERM_ENBL	0x04
 #define MSIC_ADCRRDATA_ENBL	0x05
 #define MSIC_CHANL_MASK_VAL	0x0F
@@ -75,8 +72,8 @@
 #define ADC_VAL60C		315
 
 /* ADC base addresses */
-#define ADC_CHNL_START_ADDR	0x1C5	/* increments by 1 */
-#define ADC_DATA_START_ADDR	0x1D4	/* increments by 2 */
+#define ADC_CHNL_START_ADDR	INTEL_MSIC_ADC1ADDR0	/* increments by 1 */
+#define ADC_DATA_START_ADDR	INTEL_MSIC_ADC1SNS0H	/* increments by 2 */
 
 /* MSIC die attributes */
 #define MSIC_DIE_ADC_MIN	488
@@ -189,17 +186,17 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
 	addr = td_info->chnl_addr;
 
 	/* Enable the msic for conversion before reading */
-	ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
 	if (ret)
 		return ret;
 
 	/* Re-toggle the RRDATARD bit (temporary workaround) */
-	ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
 	if (ret)
 		return ret;
 
 	/* Read the higher bits of data */
-	ret = intel_scu_ipc_ioread8(addr, &data);
+	ret = intel_msic_reg_read(addr, &data);
 	if (ret)
 		return ret;
 
@@ -207,7 +204,7 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
 	adc_val = (data << 2);
 	addr++;
 
-	ret = intel_scu_ipc_ioread8(addr, &data);/* Read lower bits */
+	ret = intel_msic_reg_read(addr, &data);/* Read lower bits */
 	if (ret)
 		return ret;
 
@@ -235,7 +232,7 @@ static int configure_adc(int val)
 	int ret;
 	uint8_t data;
 
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
 	if (ret)
 		return ret;
 
@@ -246,7 +243,7 @@ static int configure_adc(int val)
 		/* Just stop the ADC */
 		data &= (~MSIC_ADC_START);
 	}
-	return intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL1, data);
+	return intel_msic_reg_write(INTEL_MSIC_ADC1CNTL1, data);
 }
 
 /**
@@ -262,21 +259,21 @@ static int set_up_therm_channel(u16 base_addr)
 	int ret;
 
 	/* Enable all the sensor channels */
-	ret = intel_scu_ipc_iowrite8(base_addr, SKIN_SENSOR0_CODE);
+	ret = intel_msic_reg_write(base_addr, SKIN_SENSOR0_CODE);
 	if (ret)
 		return ret;
 
-	ret = intel_scu_ipc_iowrite8(base_addr + 1, SKIN_SENSOR1_CODE);
+	ret = intel_msic_reg_write(base_addr + 1, SKIN_SENSOR1_CODE);
 	if (ret)
 		return ret;
 
-	ret = intel_scu_ipc_iowrite8(base_addr + 2, SYS_SENSOR_CODE);
+	ret = intel_msic_reg_write(base_addr + 2, SYS_SENSOR_CODE);
 	if (ret)
 		return ret;
 
 	/* Since this is the last channel, set the stop bit
 	 * to 1 by ORing the DIE_SENSOR_CODE with 0x10 */
-	ret = intel_scu_ipc_iowrite8(base_addr + 3,
+	ret = intel_msic_reg_write(base_addr + 3,
 			(MSIC_DIE_SENSOR_CODE | 0x10));
 	if (ret)
 		return ret;
@@ -295,11 +292,11 @@ static int reset_stopbit(uint16_t addr)
 {
 	int ret;
 	uint8_t data;
-	ret = intel_scu_ipc_ioread8(addr, &data);
+	ret = intel_msic_reg_read(addr, &data);
 	if (ret)
 		return ret;
 	/* Set the stop bit to zero */
-	return intel_scu_ipc_iowrite8(addr, (data & 0xEF));
+	return intel_msic_reg_write(addr, (data & 0xEF));
 }
 
 /**
@@ -322,7 +319,7 @@ static int find_free_channel(void)
 	uint8_t data;
 
 	/* check whether ADC is enabled */
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
 	if (ret)
 		return ret;
 
@@ -331,7 +328,7 @@ static int find_free_channel(void)
 
 	/* ADC is already enabled; Looking for an empty channel */
 	for (i = 0; i < ADC_CHANLS_MAX; i++) {
-		ret = intel_scu_ipc_ioread8(ADC_CHNL_START_ADDR + i, &data);
+		ret = intel_msic_reg_read(ADC_CHNL_START_ADDR + i, &data);
 		if (ret)
 			return ret;
 
@@ -359,12 +356,14 @@ static int mid_initialize_adc(struct device *dev)
 	 * Ensure that adctherm is disabled before we
 	 * initialize the ADC
 	 */
-	ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL3, &data);
+	ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL3, &data);
 	if (ret)
 		return ret;
 
-	if (data & MSIC_ADCTHERM_MASK)
-		dev_warn(dev, "ADCTHERM already set");
+	data &= ~MSIC_ADCTHERM_MASK;
+	ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, data);
+	if (ret)
+		return ret;
 
 	/* Index of the first channel in which the stop bit is set */
 	channel_index = find_free_channel();
@@ -546,7 +545,7 @@ static int mid_thermal_remove(struct platform_device *pdev)
 	return configure_adc(0);
 }
 
-#define DRIVER_NAME "msic_sensor"
+#define DRIVER_NAME "msic_thermal"
 
 static const struct platform_device_id therm_id_table[] = {
 	{ DRIVER_NAME, 1 },
diff --git a/drivers/platform/x86/intel_rar_register.c b/drivers/platform/x86/intel_rar_register.c
deleted file mode 100644
index c8a6aed..0000000
--- a/drivers/platform/x86/intel_rar_register.c
+++ /dev/null
@@ -1,669 +0,0 @@
-/*
- *  rar_register.c - An Intel Restricted Access Region register driver
- *
- *  Copyright(c) 2009 Intel Corporation. All rights reserved.
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License as
- *  published by the Free Software Foundation; either version 2 of the
- *  License, or (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- *  General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA
- *  02111-1307, USA.
- *
- * -------------------------------------------------------------------
- *  20091204 Mark Allyn <mark.a.allyn@intel.com>
- *	     Ossama Othman <ossama.othman@intel.com>
- *	Cleanup per feedback from Alan Cox and Arjan Van De Ven
- *
- *  20090806 Ossama Othman <ossama.othman@intel.com>
- *      Return zero high address if upper 22 bits is zero.
- *      Cleaned up checkpatch errors.
- *      Clarified that driver is dealing with bus addresses.
- *
- *  20090702 Ossama Othman <ossama.othman@intel.com>
- *      Removed unnecessary include directives
- *      Cleaned up spinlocks.
- *      Cleaned up logging.
- *      Improved invalid parameter checks.
- *      Fixed and simplified RAR address retrieval and RAR locking
- *      code.
- *
- *  20090626 Mark Allyn <mark.a.allyn@intel.com>
- *      Initial publish
- */
-
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/spinlock.h>
-#include <linux/device.h>
-#include <linux/kernel.h>
-#include <linux/rar_register.h>
-
-/* === Lincroft Message Bus Interface === */
-#define LNC_MCR_OFFSET		0xD0	/* Message Control Register */
-#define LNC_MDR_OFFSET		0xD4	/* Message Data Register */
-
-/* Message Opcodes */
-#define LNC_MESSAGE_READ_OPCODE	0xD0
-#define LNC_MESSAGE_WRITE_OPCODE 0xE0
-
-/* Message Write Byte Enables */
-#define LNC_MESSAGE_BYTE_WRITE_ENABLES	0xF
-
-/* B-unit Port */
-#define LNC_BUNIT_PORT	0x3
-
-/* === Lincroft B-Unit Registers - Programmed by IA32 firmware === */
-#define LNC_BRAR0L	0x10
-#define LNC_BRAR0H	0x11
-#define LNC_BRAR1L	0x12
-#define LNC_BRAR1H	0x13
-/* Reserved for SeP */
-#define LNC_BRAR2L	0x14
-#define LNC_BRAR2H	0x15
-
-/* Moorestown supports three restricted access regions. */
-#define MRST_NUM_RAR 3
-
-/* RAR Bus Address Range */
-struct rar_addr {
-	dma_addr_t low;
-	dma_addr_t high;
-};
-
-/*
- *	We create one of these for each RAR
- */
-struct client {
-	int (*callback)(unsigned long data);
-	unsigned long driver_priv;
-	bool busy;
-};
-
-static DEFINE_MUTEX(rar_mutex);
-static DEFINE_MUTEX(lnc_reg_mutex);
-
-/*
- *	One per RAR device (currently only one device)
- */
-struct rar_device {
-	struct rar_addr rar_addr[MRST_NUM_RAR];
-	struct pci_dev *rar_dev;
-	bool registered;
-	bool allocated;
-	struct client client[MRST_NUM_RAR];
-};
-
-/* Current platforms have only one rar_device for 3 rar regions */
-static struct rar_device my_rar_device;
-
-/*
- *	Abstract out multiple device support. Current platforms only
- *	have a single RAR device.
- */
-
-/**
- *	alloc_rar_device	-	return a new RAR structure
- *
- *	Return a new (but not yet ready) RAR device object
- */
-static struct rar_device *alloc_rar_device(void)
-{
-	if (my_rar_device.allocated)
-		return NULL;
-	my_rar_device.allocated = 1;
-	return &my_rar_device;
-}
-
-/**
- *	free_rar_device		-	free a RAR object
- *	@rar: the RAR device being freed
- *
- *	Release a RAR object and any attached resources
- */
-static void free_rar_device(struct rar_device *rar)
-{
-	pci_dev_put(rar->rar_dev);
-	rar->allocated = 0;
-}
-
-/**
- *	_rar_to_device		-	return the device handling this RAR
- *	@rar: RAR number
- *	@off: returned offset
- *
- *	Internal helper for looking up RAR devices. This and alloc are the
- *	two functions that need touching to go to multiple RAR devices.
- */
-static struct rar_device *_rar_to_device(int rar, int *off)
-{
-	if (rar >= 0 && rar < MRST_NUM_RAR) {
-		*off = rar;
-		return &my_rar_device;
-	}
-	return NULL;
-}
-
-/**
- *	rar_to_device		-	return the device handling this RAR
- *	@rar: RAR number
- *	@off: returned offset
- *
- *	Return the device this RAR maps to if one is present, otherwise
- *	returns NULL. Reports the offset relative to the base of this
- *	RAR device in off.
- */
-static struct rar_device *rar_to_device(int rar, int *off)
-{
-	struct rar_device *rar_dev = _rar_to_device(rar, off);
-	if (rar_dev == NULL || !rar_dev->registered)
-		return NULL;
-	return rar_dev;
-}
-
-/**
- *	rar_to_client		-	return the client handling this RAR
- *	@rar: RAR number
- *
- *	Return the client this RAR maps to if a mapping is known, otherwise
- *	returns NULL.
- */
-static struct client *rar_to_client(int rar)
-{
-	int idx;
-	struct rar_device *r = _rar_to_device(rar, &idx);
-	if (r != NULL)
-		return &r->client[idx];
-	return NULL;
-}
-
-/**
- *	rar_read_addr		-	retrieve a RAR mapping
- *	@pdev: PCI device for the RAR
- *	@offset: offset for message
- *	@addr: returned address
- *
- *	Reads the address of a given RAR register. Returns 0 on success
- *	or an error code on failure.
- */
-static int rar_read_addr(struct pci_dev *pdev, int offset, dma_addr_t *addr)
-{
-	/*
-	 * ======== The Lincroft Message Bus Interface ========
-	 * Lincroft registers may be obtained via PCI from
-	 * the host bridge using the Lincroft Message Bus
-	 * Interface.  That message bus interface is generally
-	 * comprised of two registers: a control register (MCR, 0xDO)
-	 * and a data register (MDR, 0xD4).
-	 *
-	 * The MCR (message control register) format is the following:
-	 *   1.  [31:24]: Opcode
-	 *   2.  [23:16]: Port
-	 *   3.  [15:8]: Register Offset
-	 *   4.  [7:4]: Byte Enables (use 0xF to set all of these bits
-	 *              to 1)
-	 *   5.  [3:0]: reserved
-	 *
-	 *  Read (0xD0) and write (0xE0) opcodes are written to the
-	 *  control register when reading and writing to Lincroft
-	 *  registers, respectively.
-	 *
-	 *  We're interested in registers found in the Lincroft
-	 *  B-unit.  The B-unit port is 0x3.
-	 *
-	 *  The six B-unit RAR register offsets we use are listed
-	 *  earlier in this file.
-	 *
-	 *  Lastly writing to the MCR register requires the "Byte
-	 *  enables" bits to be set to 1.  This may be achieved by
-	 *  writing 0xF at bit 4.
-	 *
-	 * The MDR (message data register) format is the following:
-	 *   1. [31:0]: Read/Write Data
-	 *
-	 *  Data being read from this register is only available after
-	 *  writing the appropriate control message to the MCR
-	 *  register.
-	 *
-	 *  Data being written to this register must be written before
-	 *  writing the appropriate control message to the MCR
-	 *  register.
-	*/
-
-	int result;
-	u32 addr32;
-
-	/* Construct control message */
-	u32 const message =
-		 (LNC_MESSAGE_READ_OPCODE << 24)
-		 | (LNC_BUNIT_PORT << 16)
-		 | (offset << 8)
-		 | (LNC_MESSAGE_BYTE_WRITE_ENABLES << 4);
-
-	dev_dbg(&pdev->dev, "Offset for 'get' LNC MSG is %x\n", offset);
-
-	/*
-	* We synchronize access to the Lincroft MCR and MDR registers
-	* until BOTH the command is issued through the MCR register
-	* and the corresponding data is read from the MDR register.
-	* Otherwise a race condition would exist between accesses to
-	* both registers.
-	*/
-
-	mutex_lock(&lnc_reg_mutex);
-
-	/* Send the control message */
-	result = pci_write_config_dword(pdev, LNC_MCR_OFFSET, message);
-	if (!result) {
-		/* Read back the address as a 32bit value */
-		result = pci_read_config_dword(pdev, LNC_MDR_OFFSET, &addr32);
-		*addr = (dma_addr_t)addr32;
-	}
-	mutex_unlock(&lnc_reg_mutex);
-	return result;
-}
-
-/**
- *	rar_set_addr		-	Set a RAR mapping
- *	@pdev: PCI device for the RAR
- *	@offset: offset for message
- *	@addr: address to set
- *
- *	Sets the address of a given RAR register. Returns 0 on success
- *	or an error code on failure.
- */
-static int rar_set_addr(struct pci_dev *pdev,
-	int offset,
-	dma_addr_t addr)
-{
-	/*
-	* Data being written to this register must be written before
-	* writing the appropriate control message to the MCR
-	* register.
-	* See rar_get_addrs() for a description of the
-	* message bus interface being used here.
-	*/
-
-	int result;
-
-	/* Construct control message */
-	u32 const message = (LNC_MESSAGE_WRITE_OPCODE << 24)
-		| (LNC_BUNIT_PORT << 16)
-		| (offset << 8)
-		| (LNC_MESSAGE_BYTE_WRITE_ENABLES << 4);
-
-	/*
-	* We synchronize access to the Lincroft MCR and MDR registers
-	* until BOTH the command is issued through the MCR register
-	* and the corresponding data is read from the MDR register.
-	* Otherwise a race condition would exist between accesses to
-	* both registers.
-	*/
-
-	mutex_lock(&lnc_reg_mutex);
-
-	/* Send the control message */
-	result = pci_write_config_dword(pdev, LNC_MDR_OFFSET, addr);
-	if (!result)
-		/* And address */
-		result = pci_write_config_dword(pdev, LNC_MCR_OFFSET, message);
-
-	mutex_unlock(&lnc_reg_mutex);
-	return result;
-}
-
-/*
- *	rar_init_params		-	Initialize RAR parameters
- *	@rar: RAR device to initialise
- *
- *	Initialize RAR parameters, such as bus addresses, etc. Returns 0
- *	on success, or an error code on failure.
- */
-static int init_rar_params(struct rar_device *rar)
-{
-	struct pci_dev *pdev = rar->rar_dev;
-	unsigned int i;
-	int result = 0;
-	int offset = 0x10;	/* RAR 0 to 2 in order low/high/low/high/... */
-
-	/* Retrieve RAR start and end bus addresses.
-	* Access the RAR registers through the Lincroft Message Bus
-	* Interface on PCI device: 00:00.0 Host bridge.
-	*/
-
-	for (i = 0; i < MRST_NUM_RAR; ++i) {
-		struct rar_addr *addr = &rar->rar_addr[i];
-
-		result = rar_read_addr(pdev, offset++, &addr->low);
-		if (result != 0)
-			return result;
-
-		result = rar_read_addr(pdev, offset++, &addr->high);
-		if (result != 0)
-			return result;
-
-
-		/*
-		* Only the upper 22 bits of the RAR addresses are
-		* stored in their corresponding RAR registers so we
-		* must set the lower 10 bits accordingly.
-
-		* The low address has its lower 10 bits cleared, and
-		* the high address has all its lower 10 bits set,
-		* e.g.:
-		* low = 0x2ffffc00
-		*/
-
-		addr->low &= (dma_addr_t)0xfffffc00u;
-
-		/*
-		* Set bits 9:0 on uppser address if bits 31:10 are non
-		* zero; otherwize clear all bits
-		*/
-
-		if ((addr->high & 0xfffffc00u) == 0)
-			addr->high = 0;
-		else
-			addr->high |= 0x3ffu;
-	}
-	/* Done accessing the device. */
-
-	if (result == 0) {
-		for (i = 0; i != MRST_NUM_RAR; ++i) {
-			/*
-			* "BRAR" refers to the RAR registers in the
-			* Lincroft B-unit.
-			*/
-			dev_info(&pdev->dev, "BRAR[%u] bus address range = "
-			  "[%lx, %lx]\n", i,
-			  (unsigned long)rar->rar_addr[i].low,
-			  (unsigned long)rar->rar_addr[i].high);
-		}
-	}
-	return result;
-}
-
-/**
- *	rar_get_address		-	get the bus address in a RAR
- *	@start: return value of start address of block
- *	@end: return value of end address of block
- *
- *	The rar_get_address function is used by other device drivers
- *	to obtain RAR address information on a RAR. It takes three
- *	parameters:
- *
- *	The function returns a 0 upon success or an error if there is no RAR
- *	facility on this system.
- */
-int rar_get_address(int rar_index, dma_addr_t *start, dma_addr_t *end)
-{
-	int idx;
-	struct rar_device *rar = rar_to_device(rar_index, &idx);
-
-	if (rar == NULL) {
-		WARN_ON(1);
-		return -ENODEV;
-	}
-
-	*start = rar->rar_addr[idx].low;
-	*end = rar->rar_addr[idx].high;
-	return 0;
-}
-EXPORT_SYMBOL(rar_get_address);
-
-/**
- *	rar_lock	-	lock a RAR register
- *	@rar_index: RAR to lock (0-2)
- *
- *	The rar_lock function is ued by other device drivers to lock an RAR.
- *	once a RAR is locked, it stays locked until the next system reboot.
- *
- *	The function returns a 0 upon success or an error if there is no RAR
- *	facility on this system, or the locking fails
- */
-int rar_lock(int rar_index)
-{
-	struct rar_device *rar;
-	int result;
-	int idx;
-	dma_addr_t low, high;
-
-	rar = rar_to_device(rar_index, &idx);
-
-	if (rar == NULL) {
-		WARN_ON(1);
-		return -EINVAL;
-	}
-
-	low = rar->rar_addr[idx].low & 0xfffffc00u;
-	high = rar->rar_addr[idx].high & 0xfffffc00u;
-
-	/*
-	* Only allow I/O from the graphics and Langwell;
-	* not from the x86 processor
-	*/
-
-	if (rar_index == RAR_TYPE_VIDEO) {
-		low |= 0x00000009;
-		high |= 0x00000015;
-	} else if (rar_index == RAR_TYPE_AUDIO) {
-		/* Only allow I/O from Langwell; nothing from x86 */
-		low |= 0x00000008;
-		high |= 0x00000018;
-	} else
-		/* Read-only from all agents */
-		high |= 0x00000018;
-
-	/*
-	* Now program the register using the Lincroft message
-	* bus interface.
-	*/
-	result = rar_set_addr(rar->rar_dev,
-				2 * idx, low);
-
-	if (result == 0)
-		result = rar_set_addr(rar->rar_dev,
-				2 * idx + 1, high);
-
-	return result;
-}
-EXPORT_SYMBOL(rar_lock);
-
-/**
- *	register_rar		-	register a RAR handler
- *	@num: RAR we wish to register for
- *	@callback: function to call when RAR support is available
- *	@data: data to pass to this function
- *
- *	The register_rar function is to used by other device drivers
- *	to ensure that this driver is ready. As we cannot be sure of
- *	the compile/execute order of drivers in the kernel, it is
- *	best to give this driver a callback function to call when
- *	it is ready to give out addresses. The callback function
- *	would have those steps that continue the initialization of
- *	a driver that do require a valid RAR address. One of those
- *	steps would be to call rar_get_address()
- *
- *	This function return 0 on success or an error code on failure.
- */
-int register_rar(int num, int (*callback)(unsigned long data),
-							unsigned long data)
-{
-	/* For now we hardcode a single RAR device */
-	struct rar_device *rar;
-	struct client *c;
-	int idx;
-	int retval = 0;
-
-	mutex_lock(&rar_mutex);
-
-	/* Do we have a client mapping for this RAR number ? */
-	c = rar_to_client(num);
-	if (c == NULL) {
-		retval = -ERANGE;
-		goto done;
-	}
-	/* Is it claimed ? */
-	if (c->busy) {
-		retval = -EBUSY;
-		goto done;
-	}
-	c->busy = 1;
-
-	/* See if we have a handler for this RAR yet, if we do then fire it */
-	rar = rar_to_device(num, &idx);
-
-	if (rar) {
-		/*
-		* if the driver already registered, then we can simply
-		* call the callback right now
-		*/
-		(*callback)(data);
-		goto done;
-	}
-
-	/* Arrange to be called back when the hardware is found */
-	c->callback = callback;
-	c->driver_priv = data;
-done:
-	mutex_unlock(&rar_mutex);
-	return retval;
-}
-EXPORT_SYMBOL(register_rar);
-
-/**
- *	unregister_rar	-	release a RAR allocation
- *	@num: RAR number
- *
- *	Releases a RAR allocation, or pending allocation. If a callback is
- *	pending then this function will either complete before the unregister
- *	returns or not at all.
- */
-
-void unregister_rar(int num)
-{
-	struct client *c;
-
-	mutex_lock(&rar_mutex);
-	c = rar_to_client(num);
-	if (c == NULL || !c->busy)
-		WARN_ON(1);
-	else
-		c->busy = 0;
-	mutex_unlock(&rar_mutex);
-}
-EXPORT_SYMBOL(unregister_rar);
-
-/**
- *	rar_callback		-	Process callbacks
- *	@rar: new RAR device
- *
- *	Process the callbacks for a newly found RAR device.
- */
-
-static void rar_callback(struct rar_device *rar)
-{
-	struct client *c = &rar->client[0];
-	int i;
-
-	mutex_lock(&rar_mutex);
-
-	rar->registered = 1;	/* Ensure no more callbacks queue */
-
-	for (i = 0; i < MRST_NUM_RAR; i++) {
-		if (c->callback && c->busy) {
-			c->callback(c->driver_priv);
-			c->callback = NULL;
-		}
-		c++;
-	}
-	mutex_unlock(&rar_mutex);
-}
-
-/**
- *	rar_probe		-	PCI probe callback
- *	@dev: PCI device
- *	@id: matching entry in the match table
- *
- *	A RAR device has been discovered. Initialise it and if successful
- *	process any pending callbacks that can now be completed.
- */
-static int rar_probe(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	int error;
-	struct rar_device *rar;
-
-	dev_dbg(&dev->dev, "PCI probe starting\n");
-
-	rar = alloc_rar_device();
-	if (rar == NULL)
-		return -EBUSY;
-
-	/* Enable the device */
-	error = pci_enable_device(dev);
-	if (error) {
-		dev_err(&dev->dev,
-			"Error enabling RAR register PCI device\n");
-		goto end_function;
-	}
-
-	/* Fill in the rar_device structure */
-	rar->rar_dev = pci_dev_get(dev);
-	pci_set_drvdata(dev, rar);
-
-	/*
-	 * Initialize the RAR parameters, which have to be retrieved
-	 * via the message bus interface.
-	 */
-	error = init_rar_params(rar);
-	if (error) {
-		pci_disable_device(dev);
-		dev_err(&dev->dev, "Error retrieving RAR addresses\n");
-		goto end_function;
-	}
-	/* now call anyone who has registered (using callbacks) */
-	rar_callback(rar);
-	return 0;
-end_function:
-	free_rar_device(rar);
-	return error;
-}
-
-static DEFINE_PCI_DEVICE_TABLE(rar_pci_id_tbl) = {
-	{ PCI_VDEVICE(INTEL, 0x4110) },
-	{ 0 }
-};
-
-MODULE_DEVICE_TABLE(pci, rar_pci_id_tbl);
-
-/* field for registering driver to PCI device */
-static struct pci_driver rar_pci_driver = {
-	.name = "rar_register_driver",
-	.id_table = rar_pci_id_tbl,
-	.probe = rar_probe,
-	/* Cannot be unplugged - no remove */
-};
-
-static int __init rar_init_handler(void)
-{
-	return pci_register_driver(&rar_pci_driver);
-}
-
-static void __exit rar_exit_handler(void)
-{
-	pci_unregister_driver(&rar_pci_driver);
-}
-
-module_init(rar_init_handler);
-module_exit(rar_exit_handler);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Intel Restricted Access Region Register Driver");
diff --git a/drivers/platform/x86/intel_scu_ipc.c b/drivers/platform/x86/intel_scu_ipc.c
index f00d0d1..9215ed7 100644
--- a/drivers/platform/x86/intel_scu_ipc.c
+++ b/drivers/platform/x86/intel_scu_ipc.c
@@ -159,7 +159,7 @@ static inline int busy_loop(void) /* Wait till scu status is busy */
 /* Read/Write power control(PMIC in Langwell, MSIC in PenWell) registers */
 static int pwr_reg_rdwr(u16 *addr, u8 *data, u32 count, u32 op, u32 id)
 {
-	int i, nc, bytes, d;
+	int nc;
 	u32 offset = 0;
 	int err;
 	u8 cbuf[IPC_WWBUF_SIZE] = { };
@@ -174,55 +174,34 @@ static int pwr_reg_rdwr(u16 *addr, u8 *data, u32 count, u32 op, u32 id)
 		return -ENODEV;
 	}
 
-	if (platform != MRST_CPU_CHIP_PENWELL) {
-		bytes = 0;
-		d = 0;
-		for (i = 0; i < count; i++) {
-			cbuf[bytes++] = addr[i];
-			cbuf[bytes++] = addr[i] >> 8;
-			if (id != IPC_CMD_PCNTRL_R)
-				cbuf[bytes++] = data[d++];
-			if (id == IPC_CMD_PCNTRL_M)
-				cbuf[bytes++] = data[d++];
-		}
-		for (i = 0; i < bytes; i += 4)
-			ipc_data_writel(wbuf[i/4], i);
-		ipc_command(bytes << 16 |  id << 12 | 0 << 8 | op);
-	} else {
-		for (nc = 0; nc < count; nc++, offset += 2) {
-			cbuf[offset] = addr[nc];
-			cbuf[offset + 1] = addr[nc] >> 8;
-		}
+	for (nc = 0; nc < count; nc++, offset += 2) {
+		cbuf[offset] = addr[nc];
+		cbuf[offset + 1] = addr[nc] >> 8;
+	}
 
-		if (id == IPC_CMD_PCNTRL_R) {
-			for (nc = 0, offset = 0; nc < count; nc++, offset += 4)
-				ipc_data_writel(wbuf[nc], offset);
-			ipc_command((count*2) << 16 |  id << 12 | 0 << 8 | op);
-		} else if (id == IPC_CMD_PCNTRL_W) {
-			for (nc = 0; nc < count; nc++, offset += 1)
-				cbuf[offset] = data[nc];
-			for (nc = 0, offset = 0; nc < count; nc++, offset += 4)
-				ipc_data_writel(wbuf[nc], offset);
-			ipc_command((count*3) << 16 |  id << 12 | 0 << 8 | op);
-		} else if (id == IPC_CMD_PCNTRL_M) {
-			cbuf[offset] = data[0];
-			cbuf[offset + 1] = data[1];
-			ipc_data_writel(wbuf[0], 0); /* Write wbuff */
-			ipc_command(4 << 16 |  id << 12 | 0 << 8 | op);
-		}
+	if (id == IPC_CMD_PCNTRL_R) {
+		for (nc = 0, offset = 0; nc < count; nc++, offset += 4)
+			ipc_data_writel(wbuf[nc], offset);
+		ipc_command((count*2) << 16 |  id << 12 | 0 << 8 | op);
+	} else if (id == IPC_CMD_PCNTRL_W) {
+		for (nc = 0; nc < count; nc++, offset += 1)
+			cbuf[offset] = data[nc];
+		for (nc = 0, offset = 0; nc < count; nc++, offset += 4)
+			ipc_data_writel(wbuf[nc], offset);
+		ipc_command((count*3) << 16 |  id << 12 | 0 << 8 | op);
+	} else if (id == IPC_CMD_PCNTRL_M) {
+		cbuf[offset] = data[0];
+		cbuf[offset + 1] = data[1];
+		ipc_data_writel(wbuf[0], 0); /* Write wbuff */
+		ipc_command(4 << 16 |  id << 12 | 0 << 8 | op);
 	}
 
 	err = busy_loop();
 	if (id == IPC_CMD_PCNTRL_R) { /* Read rbuf */
 		/* Workaround: values are read as 0 without memcpy_fromio */
 		memcpy_fromio(cbuf, ipcdev.ipc_base + 0x90, 16);
-		if (platform != MRST_CPU_CHIP_PENWELL) {
-			for (nc = 0, offset = 2; nc < count; nc++, offset += 3)
-				data[nc] = ipc_data_readb(offset);
-		} else {
-			for (nc = 0; nc < count; nc++)
-				data[nc] = ipc_data_readb(nc);
-		}
+		for (nc = 0; nc < count; nc++)
+			data[nc] = ipc_data_readb(nc);
 	}
 	mutex_unlock(&ipclock);
 	return err;
@@ -503,148 +482,6 @@ int intel_scu_ipc_i2c_cntrl(u32 addr, u32 *data)
 }
 EXPORT_SYMBOL(intel_scu_ipc_i2c_cntrl);
 
-#define IPC_FW_LOAD_ADDR 0xFFFC0000 /* Storage location for FW image */
-#define IPC_FW_UPDATE_MBOX_ADDR 0xFFFFDFF4 /* Mailbox between ipc and scu */
-#define IPC_MAX_FW_SIZE 262144 /* 256K storage size for loading the FW image */
-#define IPC_FW_MIP_HEADER_SIZE 2048 /* Firmware MIP header size */
-/* IPC inform SCU to get ready for update process */
-#define IPC_CMD_FW_UPDATE_READY  0x10FE
-/* IPC inform SCU to go for update process */
-#define IPC_CMD_FW_UPDATE_GO     0x20FE
-/* Status code for fw update */
-#define IPC_FW_UPDATE_SUCCESS	0x444f4e45 /* Status code 'DONE' */
-#define IPC_FW_UPDATE_BADN	0x4241444E /* Status code 'BADN' */
-#define IPC_FW_TXHIGH		0x54784849 /* Status code 'IPC_FW_TXHIGH' */
-#define IPC_FW_TXLOW		0x54784c4f /* Status code 'IPC_FW_TXLOW' */
-
-struct fw_update_mailbox {
-	u32    status;
-	u32    scu_flag;
-	u32    driver_flag;
-};
-
-
-/**
- *	intel_scu_ipc_fw_update	-	 Firmware update utility
- *	@buffer: firmware buffer
- *	@length: size of firmware buffer
- *
- *	This function provides an interface to load the firmware into
- *	the SCU. Returns 0 on success or -1 on failure
- */
-int intel_scu_ipc_fw_update(u8 *buffer, u32 length)
-{
-	void __iomem *fw_update_base;
-	struct fw_update_mailbox __iomem *mailbox = NULL;
-	int retry_cnt = 0;
-	u32 status;
-
-	mutex_lock(&ipclock);
-	fw_update_base = ioremap_nocache(IPC_FW_LOAD_ADDR, (128*1024));
-	if (fw_update_base == NULL) {
-		mutex_unlock(&ipclock);
-		return -ENOMEM;
-	}
-	mailbox = ioremap_nocache(IPC_FW_UPDATE_MBOX_ADDR,
-					sizeof(struct fw_update_mailbox));
-	if (mailbox == NULL) {
-		iounmap(fw_update_base);
-		mutex_unlock(&ipclock);
-		return -ENOMEM;
-	}
-
-	ipc_command(IPC_CMD_FW_UPDATE_READY);
-
-	/* Intitialize mailbox */
-	writel(0, &mailbox->status);
-	writel(0, &mailbox->scu_flag);
-	writel(0, &mailbox->driver_flag);
-
-	/* Driver copies the 2KB MIP header to SRAM at 0xFFFC0000*/
-	memcpy_toio(fw_update_base, buffer, 0x800);
-
-	/* Driver sends "FW Update" IPC command (CMD_ID 0xFE; MSG_ID 0x02).
-	* Upon receiving this command, SCU will write the 2K MIP header
-	* from 0xFFFC0000 into NAND.
-	* SCU will write a status code into the Mailbox, and then set scu_flag.
-	*/
-
-	ipc_command(IPC_CMD_FW_UPDATE_GO);
-
-	/*Driver stalls until scu_flag is set */
-	while (readl(&mailbox->scu_flag) != 1) {
-		rmb();
-		mdelay(1);
-	}
-
-	/* Driver checks Mailbox status.
-	 * If the status is 'BADN', then abort (bad NAND).
-	 * If the status is 'IPC_FW_TXLOW', then continue.
-	 */
-	while (readl(&mailbox->status) != IPC_FW_TXLOW) {
-		rmb();
-		mdelay(10);
-	}
-	mdelay(10);
-
-update_retry:
-	if (retry_cnt > 5)
-		goto update_end;
-
-	if (readl(&mailbox->status) != IPC_FW_TXLOW)
-		goto update_end;
-	buffer = buffer + 0x800;
-	memcpy_toio(fw_update_base, buffer, 0x20000);
-	writel(1, &mailbox->driver_flag);
-	while (readl(&mailbox->scu_flag) == 1) {
-		rmb();
-		mdelay(1);
-	}
-
-	/* check for 'BADN' */
-	if (readl(&mailbox->status) == IPC_FW_UPDATE_BADN)
-		goto update_end;
-
-	while (readl(&mailbox->status) != IPC_FW_TXHIGH) {
-		rmb();
-		mdelay(10);
-	}
-	mdelay(10);
-
-	if (readl(&mailbox->status) != IPC_FW_TXHIGH)
-		goto update_end;
-
-	buffer = buffer + 0x20000;
-	memcpy_toio(fw_update_base, buffer, 0x20000);
-	writel(0, &mailbox->driver_flag);
-
-	while (mailbox->scu_flag == 0) {
-		rmb();
-		mdelay(1);
-	}
-
-	/* check for 'BADN' */
-	if (readl(&mailbox->status) == IPC_FW_UPDATE_BADN)
-		goto update_end;
-
-	if (readl(&mailbox->status) == IPC_FW_TXLOW) {
-		++retry_cnt;
-		goto update_retry;
-	}
-
-update_end:
-	status = readl(&mailbox->status);
-
-	iounmap(fw_update_base);
-	iounmap(mailbox);
-	mutex_unlock(&ipclock);
-
-	if (status == IPC_FW_UPDATE_SUCCESS)
-		return 0;
-	return -EIO;
-}
-EXPORT_SYMBOL(intel_scu_ipc_fw_update);
-
 /*
  * Interrupt handler gets called when ioc bit of IPC_COMMAND_REG set to 1
  * When ioc bit is set to 1, caller api must wait for interrupt handler called
@@ -727,7 +564,6 @@ static void ipc_remove(struct pci_dev *pdev)
 }
 
 static DEFINE_PCI_DEVICE_TABLE(pci_ids) = {
-	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x080e)},
 	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x082a)},
 	{ 0,}
 };
diff --git a/drivers/platform/x86/intel_scu_ipcutil.c b/drivers/platform/x86/intel_scu_ipcutil.c
index 2d0f913..02bc5a6 100644
--- a/drivers/platform/x86/intel_scu_ipcutil.c
+++ b/drivers/platform/x86/intel_scu_ipcutil.c
@@ -26,13 +26,10 @@
 
 static int major;
 
-#define MAX_FW_SIZE 264192
-
 /* ioctl commnds */
 #define	INTE_SCU_IPC_REGISTER_READ	0
 #define INTE_SCU_IPC_REGISTER_WRITE	1
 #define INTE_SCU_IPC_REGISTER_UPDATE	2
-#define INTE_SCU_IPC_FW_UPDATE		0xA2
 
 struct scu_ipc_data {
 	u32     count;  /* No. of registers */
@@ -88,27 +85,14 @@ static long scu_ipc_ioctl(struct file *fp, unsigned int cmd,
 	if (!capable(CAP_SYS_RAWIO))
 		return -EPERM;
 
-	if (cmd == INTE_SCU_IPC_FW_UPDATE) {
-			u8 *fwbuf = kmalloc(MAX_FW_SIZE, GFP_KERNEL);
-			if (fwbuf == NULL)
-				return -ENOMEM;
-			if (copy_from_user(fwbuf, (u8 *)arg, MAX_FW_SIZE)) {
-				kfree(fwbuf);
-				return -EFAULT;
-			}
-			ret = intel_scu_ipc_fw_update(fwbuf, MAX_FW_SIZE);
-			kfree(fwbuf);
-			return ret;
-	} else {
-		if (copy_from_user(&data, argp, sizeof(struct scu_ipc_data)))
-			return -EFAULT;
-		ret = scu_reg_access(cmd, &data);
-		if (ret < 0)
-			return ret;
-		if (copy_to_user(argp, &data, sizeof(struct scu_ipc_data)))
-			return -EFAULT;
-		return 0;
-	}
+	if (copy_from_user(&data, argp, sizeof(struct scu_ipc_data)))
+		return -EFAULT;
+	ret = scu_reg_access(cmd, &data);
+	if (ret < 0)
+		return ret;
+	if (copy_to_user(argp, &data, sizeof(struct scu_ipc_data)))
+		return -EFAULT;
+	return 0;
 }
 
 static const struct file_operations scu_ipc_fops = {