Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull TTY changes from Greg Kroah-Hartman:
 "As we skipped the merge window for 3.6-rc1 for the tty tree,
  everything is now settled down and working properly, so we are ready
  for 3.7-rc1.  Here's the patchset, it's big, but the large changes are
  removing a firmware file and adding a staging tty driver (it depended
  on the tty core changes, so it's going through this tree instead of
  the staging tree.)

  All of these patches have been in the linux-next tree for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up more-or-less trivial conflicts in
 - drivers/char/pcmcia/synclink_cs.c:
    tty NULL dereference fix vs tty_port_cts_enabled() helper function
 - drivers/staging/{Kconfig,Makefile}:
    add-add conflict (dgrp driver added close to other staging drivers)
 - drivers/staging/ipack/devices/ipoctal.c:
    "split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"

* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
  tty/serial: Add kgdb_nmi driver
  tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
  tty/serial/amba-pl011: Implement poll_init callback
  tty/serial/core: Introduce poll_init callback
  kdb: Turn KGDB_KDB=n stubs into static inlines
  kdb: Implement disable_nmi command
  kernel/debug: Mask KGDB NMI upon entry
  serial: pl011: handle corruption at high clock speeds
  serial: sccnxp: Make 'default' choice in switch last
  serial: sccnxp: Remove mask termios caps for SW flow control
  serial: sccnxp: Report actual baudrate back to core
  serial: samsung: Add poll_get_char & poll_put_char
  Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
  Powerpc 8xx CPM_UART maxidl should not depend on fifo size
  Powerpc 8xx CPM_UART too many interrupts
  Powerpc 8xx CPM_UART desynchronisation
  serial: set correct baud_base for EXSYS EX-41092 Dual 16950
  serial: omap: fix the reciever line error case
  8250: blacklist Winbond CIR port
  8250_pnp: do pnp probe before legacy probe
  ...

1 files changed, 13 insertions, 13 deletions

diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index c13438c..8f1dd2c 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -171,7 +171,7 @@ static int __devinit hpdca_init_one(struct dio_dev *d,
 		return 0;
 	}
 #endif
-	memset(&port, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 
 	/* Memory mapped I/O */
 	port.iotype = UPIO_MEM;
@@ -182,7 +182,7 @@ static int __devinit hpdca_init_one(struct dio_dev *d,
 	port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
 	port.regshift = 1;
 	port.dev = &d->dev;
-	line = serial8250_register_port(&port);
+	line = serial8250_register_8250_port(&uart);
 
 	if (line < 0) {
 		printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
@@ -210,7 +210,7 @@ static int __init hp300_8250_init(void)
 #ifdef CONFIG_HPAPCI
 	int line;
 	unsigned long base;
-	struct uart_port uport;
+	struct uart_8250_port uart;
 	struct hp300_port *port;
 	int i;
 #endif
@@ -248,26 +248,26 @@ static int __init hp300_8250_init(void)
 		if (!port)
 			return -ENOMEM;
 
-		memset(&uport, 0, sizeof(struct uart_port));
+		memset(&uart, 0, sizeof(uart));
 
 		base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
 
 		/* Memory mapped I/O */
-		uport.iotype = UPIO_MEM;
-		uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
+		uart.port.iotype = UPIO_MEM;
+		uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
 			      | UPF_BOOT_AUTOCONF;
 		/* XXX - no interrupt support yet */
-		uport.irq = 0;
-		uport.uartclk = HPAPCI_BAUD_BASE * 16;
-		uport.mapbase = base;
-		uport.membase = (char *)(base + DIO_VIRADDRBASE);
-		uport.regshift = 2;
+		uart.port.irq = 0;
+		uart.port.uartclk = HPAPCI_BAUD_BASE * 16;
+		uart.port.mapbase = base;
+		uart.port.membase = (char *)(base + DIO_VIRADDRBASE);
+		uart.port.regshift = 2;
 
-		line = serial8250_register_port(&uport);
+		line = serial8250_register_8250_port(&uart);
 
 		if (line < 0) {
 			printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
-			       " %d irq %d failed\n", i, uport.irq);
+			       " %d irq %d failed\n", i, uart.port.irq);
 			kfree(port);
 			continue;
 		}