Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull TTY changes from Greg Kroah-Hartman:
 "As we skipped the merge window for 3.6-rc1 for the tty tree,
  everything is now settled down and working properly, so we are ready
  for 3.7-rc1.  Here's the patchset, it's big, but the large changes are
  removing a firmware file and adding a staging tty driver (it depended
  on the tty core changes, so it's going through this tree instead of
  the staging tree.)

  All of these patches have been in the linux-next tree for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up more-or-less trivial conflicts in
 - drivers/char/pcmcia/synclink_cs.c:
    tty NULL dereference fix vs tty_port_cts_enabled() helper function
 - drivers/staging/{Kconfig,Makefile}:
    add-add conflict (dgrp driver added close to other staging drivers)
 - drivers/staging/ipack/devices/ipoctal.c:
    "split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"

* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
  tty/serial: Add kgdb_nmi driver
  tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
  tty/serial/amba-pl011: Implement poll_init callback
  tty/serial/core: Introduce poll_init callback
  kdb: Turn KGDB_KDB=n stubs into static inlines
  kdb: Implement disable_nmi command
  kernel/debug: Mask KGDB NMI upon entry
  serial: pl011: handle corruption at high clock speeds
  serial: sccnxp: Make 'default' choice in switch last
  serial: sccnxp: Remove mask termios caps for SW flow control
  serial: sccnxp: Report actual baudrate back to core
  serial: samsung: Add poll_get_char & poll_put_char
  Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
  Powerpc 8xx CPM_UART maxidl should not depend on fifo size
  Powerpc 8xx CPM_UART too many interrupts
  Powerpc 8xx CPM_UART desynchronisation
  serial: set correct baud_base for EXSYS EX-41092 Dual 16950
  serial: omap: fix the reciever line error case
  8250: blacklist Winbond CIR port
  8250_pnp: do pnp probe before legacy probe
  ...

1 files changed, 32 insertions, 27 deletions

diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index a2f2365..f8ee250 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -1,5 +1,5 @@
 /*
- *  Probe module for 8250/16550-type ISAPNP serial ports.
+ *  Probe for 8250/16550-type ISAPNP serial ports.
  *
  *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
  *
@@ -25,7 +25,7 @@
 #include "8250.h"
 
 #define UNKNOWN_DEV 0x3000
-
+#define CIR_PORT	0x0800
 
 static const struct pnp_device_id pnp_dev_table[] = {
 	/* Archtek America Corp. */
@@ -362,6 +362,9 @@ static const struct pnp_device_id pnp_dev_table[] = {
 	{	"PNPCXXX",		UNKNOWN_DEV	},
 	/* More unknown PnP modems */
 	{	"PNPDXXX",		UNKNOWN_DEV	},
+	/* Winbond CIR port, should not be probed. We should keep track
+	   of it to prevent the legacy serial driver from probing it */
+	{	"WEC1022",		CIR_PORT	},
 	{	"",			0	}
 };
 
@@ -409,7 +412,7 @@ static int __devinit check_resources(struct pnp_dev *dev)
  * PnP modems, alternatively we must hardcode all modems in pnp_devices[]
  * table.
  */
-static int __devinit serial_pnp_guess_board(struct pnp_dev *dev, int *flags)
+static int __devinit serial_pnp_guess_board(struct pnp_dev *dev)
 {
 	if (!(check_name(pnp_dev_name(dev)) ||
 		(dev->card && check_name(dev->card->name))))
@@ -424,42 +427,49 @@ static int __devinit serial_pnp_guess_board(struct pnp_dev *dev, int *flags)
 static int __devinit
 serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 {
-	struct uart_port port;
+	struct uart_8250_port uart;
 	int ret, line, flags = dev_id->driver_data;
 
 	if (flags & UNKNOWN_DEV) {
-		ret = serial_pnp_guess_board(dev, &flags);
+		ret = serial_pnp_guess_board(dev);
 		if (ret < 0)
 			return ret;
 	}
 
-	memset(&port, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 	if (pnp_irq_valid(dev, 0))
-		port.irq = pnp_irq(dev, 0);
-	if (pnp_port_valid(dev, 0)) {
-		port.iobase = pnp_port_start(dev, 0);
-		port.iotype = UPIO_PORT;
+		uart.port.irq = pnp_irq(dev, 0);
+	if ((flags & CIR_PORT) && pnp_port_valid(dev, 2)) {
+		uart.port.iobase = pnp_port_start(dev, 2);
+		uart.port.iotype = UPIO_PORT;
+	} else if (pnp_port_valid(dev, 0)) {
+		uart.port.iobase = pnp_port_start(dev, 0);
+		uart.port.iotype = UPIO_PORT;
 	} else if (pnp_mem_valid(dev, 0)) {
-		port.mapbase = pnp_mem_start(dev, 0);
-		port.iotype = UPIO_MEM;
-		port.flags = UPF_IOREMAP;
+		uart.port.mapbase = pnp_mem_start(dev, 0);
+		uart.port.iotype = UPIO_MEM;
+		uart.port.flags = UPF_IOREMAP;
 	} else
 		return -ENODEV;
 
 #ifdef SERIAL_DEBUG_PNP
 	printk(KERN_DEBUG
 		"Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n",
-		       port.iobase, port.mapbase, port.irq, port.iotype);
+		       uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype);
 #endif
+	if (flags & CIR_PORT) {
+		uart.port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE;
+		uart.port.type = PORT_8250_CIR;
+	}
 
-	port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
 	if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
-		port.flags |= UPF_SHARE_IRQ;
-	port.uartclk = 1843200;
-	port.dev = &dev->dev;
+		uart.port.flags |= UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &dev->dev;
 
-	line = serial8250_register_port(&port);
-	if (line < 0)
+	line = serial8250_register_8250_port(&uart);
+	if (line < 0 || (flags & CIR_PORT))
 		return -ENODEV;
 
 	pnp_set_drvdata(dev, (void *)((long)line + 1));
@@ -507,18 +517,13 @@ static struct pnp_driver serial_pnp_driver = {
 	.id_table	= pnp_dev_table,
 };
 
-static int __init serial8250_pnp_init(void)
+int serial8250_pnp_init(void)
 {
 	return pnp_register_driver(&serial_pnp_driver);
 }
 
-static void __exit serial8250_pnp_exit(void)
+void serial8250_pnp_exit(void)
 {
 	pnp_unregister_driver(&serial_pnp_driver);
 }
 
-module_init(serial8250_pnp_init);
-module_exit(serial8250_pnp_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Generic 8250/16x50 PnP serial driver");