abx500-chargalg: Add abx500 charging algorithm

This is a charging algorithm driver for abx500 variants. It is the central
entity for battery driver and is responsible for charging and monitoring
the battery driver. It is a hardware independant driver and also monitors
other abx500 power supply devices.

Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>

1 files changed, 273 insertions, 0 deletions

diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 9970337..8344196 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -152,6 +152,279 @@ struct abx500_init_settings {
 	u8 setting;
 };
 
+/* Battery driver related data */
+/*
+ * ADC for the battery thermistor.
+ * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
+ * with a NTC resistor to both identify the battery and to measure its
+ * temperature. Different phone manufactures uses different techniques to both
+ * identify the battery and to read its temperature.
+ */
+enum abx500_adc_therm {
+	ABx500_ADC_THERM_BATCTRL,
+	ABx500_ADC_THERM_BATTEMP,
+};
+
+/**
+ * struct abx500_res_to_temp - defines one point in a temp to res curve. To
+ * be used in battery packs that combines the identification resistor with a
+ * NTC resistor.
+ * @temp:			battery pack temperature in Celcius
+ * @resist:			NTC resistor net total resistance
+ */
+struct abx500_res_to_temp {
+	int temp;
+	int resist;
+};
+
+/**
+ * struct abx500_v_to_cap - Table for translating voltage to capacity
+ * @voltage:		Voltage in mV
+ * @capacity:		Capacity in percent
+ */
+struct abx500_v_to_cap {
+	int voltage;
+	int capacity;
+};
+
+/* Forward declaration */
+struct abx500_fg;
+
+/**
+ * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
+ * if not specified
+ * @recovery_sleep_timer:	Time between measurements while recovering
+ * @recovery_total_time:	Total recovery time
+ * @init_timer:			Measurement interval during startup
+ * @init_discard_time:		Time we discard voltage measurement at startup
+ * @init_total_time:		Total init time during startup
+ * @high_curr_time:		Time current has to be high to go to recovery
+ * @accu_charging:		FG accumulation time while charging
+ * @accu_high_curr:		FG accumulation time in high current mode
+ * @high_curr_threshold:	High current threshold, in mA
+ * @lowbat_threshold:		Low battery threshold, in mV
+ * @overbat_threshold:		Over battery threshold, in mV
+ * @battok_falling_th_sel0	Threshold in mV for battOk signal sel0
+ *				Resolution in 50 mV step.
+ * @battok_raising_th_sel1	Threshold in mV for battOk signal sel1
+ *				Resolution in 50 mV step.
+ * @user_cap_limit		Capacity reported from user must be within this
+ *				limit to be considered as sane, in percentage
+ *				points.
+ * @maint_thres			This is the threshold where we stop reporting
+ *				battery full while in maintenance, in per cent
+ */
+struct abx500_fg_parameters {
+	int recovery_sleep_timer;
+	int recovery_total_time;
+	int init_timer;
+	int init_discard_time;
+	int init_total_time;
+	int high_curr_time;
+	int accu_charging;
+	int accu_high_curr;
+	int high_curr_threshold;
+	int lowbat_threshold;
+	int overbat_threshold;
+	int battok_falling_th_sel0;
+	int battok_raising_th_sel1;
+	int user_cap_limit;
+	int maint_thres;
+};
+
+/**
+ * struct abx500_charger_maximization - struct used by the board config.
+ * @use_maxi:		Enable maximization for this battery type
+ * @maxi_chg_curr:	Maximum charger current allowed
+ * @maxi_wait_cycles:	cycles to wait before setting charger current
+ * @charger_curr_step	delta between two charger current settings (mA)
+ */
+struct abx500_maxim_parameters {
+	bool ena_maxi;
+	int chg_curr;
+	int wait_cycles;
+	int charger_curr_step;
+};
+
+/**
+ * struct abx500_battery_type - different batteries supported
+ * @name:			battery technology
+ * @resis_high:			battery upper resistance limit
+ * @resis_low:			battery lower resistance limit
+ * @charge_full_design:		Maximum battery capacity in mAh
+ * @nominal_voltage:		Nominal voltage of the battery in mV
+ * @termination_vol:		max voltage upto which battery can be charged
+ * @termination_curr		battery charging termination current in mA
+ * @recharge_vol		battery voltage limit that will trigger a new
+ *				full charging cycle in the case where maintenan-
+ *				-ce charging has been disabled
+ * @normal_cur_lvl:		charger current in normal state in mA
+ * @normal_vol_lvl:		charger voltage in normal state in mV
+ * @maint_a_cur_lvl:		charger current in maintenance A state in mA
+ * @maint_a_vol_lvl:		charger voltage in maintenance A state in mV
+ * @maint_a_chg_timer_h:	charge time in maintenance A state
+ * @maint_b_cur_lvl:		charger current in maintenance B state in mA
+ * @maint_b_vol_lvl:		charger voltage in maintenance B state in mV
+ * @maint_b_chg_timer_h:	charge time in maintenance B state
+ * @low_high_cur_lvl:		charger current in temp low/high state in mA
+ * @low_high_vol_lvl:		charger voltage in temp low/high state in mV'
+ * @battery_resistance:		battery inner resistance in mOhm.
+ * @n_r_t_tbl_elements:		number of elements in r_to_t_tbl
+ * @r_to_t_tbl:			table containing resistance to temp points
+ * @n_v_cap_tbl_elements:	number of elements in v_to_cap_tbl
+ * @v_to_cap_tbl:		Voltage to capacity (in %) table
+ * @n_batres_tbl_elements	number of elements in the batres_tbl
+ * @batres_tbl			battery internal resistance vs temperature table
+ */
+struct abx500_battery_type {
+	int name;
+	int resis_high;
+	int resis_low;
+	int charge_full_design;
+	int nominal_voltage;
+	int termination_vol;
+	int termination_curr;
+	int recharge_vol;
+	int normal_cur_lvl;
+	int normal_vol_lvl;
+	int maint_a_cur_lvl;
+	int maint_a_vol_lvl;
+	int maint_a_chg_timer_h;
+	int maint_b_cur_lvl;
+	int maint_b_vol_lvl;
+	int maint_b_chg_timer_h;
+	int low_high_cur_lvl;
+	int low_high_vol_lvl;
+	int battery_resistance;
+	int n_temp_tbl_elements;
+	struct abx500_res_to_temp *r_to_t_tbl;
+	int n_v_cap_tbl_elements;
+	struct abx500_v_to_cap *v_to_cap_tbl;
+	int n_batres_tbl_elements;
+	struct batres_vs_temp *batres_tbl;
+};
+
+/**
+ * struct abx500_bm_capacity_levels - abx500 capacity level data
+ * @critical:		critical capacity level in percent
+ * @low:		low capacity level in percent
+ * @normal:		normal capacity level in percent
+ * @high:		high capacity level in percent
+ * @full:		full capacity level in percent
+ */
+struct abx500_bm_capacity_levels {
+	int critical;
+	int low;
+	int normal;
+	int high;
+	int full;
+};
+
+/**
+ * struct abx500_bm_charger_parameters - Charger specific parameters
+ * @usb_volt_max:	maximum allowed USB charger voltage in mV
+ * @usb_curr_max:	maximum allowed USB charger current in mA
+ * @ac_volt_max:	maximum allowed AC charger voltage in mV
+ * @ac_curr_max:	maximum allowed AC charger current in mA
+ */
+struct abx500_bm_charger_parameters {
+	int usb_volt_max;
+	int usb_curr_max;
+	int ac_volt_max;
+	int ac_curr_max;
+};
+
+/**
+ * struct abx500_bm_data - abx500 battery management data
+ * @temp_under		under this temp, charging is stopped
+ * @temp_low		between this temp and temp_under charging is reduced
+ * @temp_high		between this temp and temp_over charging is reduced
+ * @temp_over		over this temp, charging is stopped
+ * @temp_now		present battery temperature
+ * @temp_interval_chg	temperature measurement interval in s when charging
+ * @temp_interval_nochg	temperature measurement interval in s when not charging
+ * @main_safety_tmr_h	safety timer for main charger
+ * @usb_safety_tmr_h	safety timer for usb charger
+ * @bkup_bat_v		voltage which we charge the backup battery with
+ * @bkup_bat_i		current which we charge the backup battery with
+ * @no_maintenance	indicates that maintenance charging is disabled
+ * @abx500_adc_therm	placement of thermistor, batctrl or battemp adc
+ * @chg_unknown_bat	flag to enable charging of unknown batteries
+ * @enable_overshoot	flag to enable VBAT overshoot control
+ * @auto_trig		flag to enable auto adc trigger
+ * @fg_res		resistance of FG resistor in 0.1mOhm
+ * @n_btypes		number of elements in array bat_type
+ * @batt_id		index of the identified battery in array bat_type
+ * @interval_charging	charge alg cycle period time when charging (sec)
+ * @interval_not_charging charge alg cycle period time when not charging (sec)
+ * @temp_hysteresis	temperature hysteresis
+ * @gnd_lift_resistance	Battery ground to phone ground resistance (mOhm)
+ * @maxi:		maximization parameters
+ * @cap_levels		capacity in percent for the different capacity levels
+ * @bat_type		table of supported battery types
+ * @chg_params		charger parameters
+ * @fg_params		fuel gauge parameters
+ */
+struct abx500_bm_data {
+	int temp_under;
+	int temp_low;
+	int temp_high;
+	int temp_over;
+	int temp_now;
+	int temp_interval_chg;
+	int temp_interval_nochg;
+	int main_safety_tmr_h;
+	int usb_safety_tmr_h;
+	int bkup_bat_v;
+	int bkup_bat_i;
+	bool no_maintenance;
+	bool chg_unknown_bat;
+	bool enable_overshoot;
+	bool auto_trig;
+	enum abx500_adc_therm adc_therm;
+	int fg_res;
+	int n_btypes;
+	int batt_id;
+	int interval_charging;
+	int interval_not_charging;
+	int temp_hysteresis;
+	int gnd_lift_resistance;
+	const struct abx500_maxim_parameters *maxi;
+	const struct abx500_bm_capacity_levels *cap_levels;
+	const struct abx500_battery_type *bat_type;
+	const struct abx500_bm_charger_parameters *chg_params;
+	const struct abx500_fg_parameters *fg_params;
+};
+
+struct abx500_chargalg_platform_data {
+	char **supplied_to;
+	size_t num_supplicants;
+};
+
+struct abx500_charger_platform_data {
+	char **supplied_to;
+	size_t num_supplicants;
+	bool autopower_cfg;
+};
+
+struct abx500_btemp_platform_data {
+	char **supplied_to;
+	size_t num_supplicants;
+};
+
+struct abx500_fg_platform_data {
+	char **supplied_to;
+	size_t num_supplicants;
+};
+
+struct abx500_bm_plat_data {
+	struct abx500_bm_data *battery;
+	struct abx500_charger_platform_data *charger;
+	struct abx500_btemp_platform_data *btemp;
+	struct abx500_fg_platform_data *fg;
+	struct abx500_chargalg_platform_data *chargalg;
+};
+
 int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
 	u8 value);
 int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,