Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

2 files changed, 144 insertions, 31 deletions

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 83d800c..a587867 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -521,6 +521,7 @@ struct station_parameters {
  * @STATION_INFO_ASSOC_REQ_IES: @assoc_req_ies filled
  * @STATION_INFO_STA_FLAGS: @sta_flags filled
  * @STATION_INFO_BEACON_LOSS_COUNT: @beacon_loss_count filled
+ * @STATION_INFO_T_OFFSET: @t_offset filled
  */
 enum station_info_flags {
 	STATION_INFO_INACTIVE_TIME	= 1<<0,
@@ -542,7 +543,8 @@ enum station_info_flags {
 	STATION_INFO_CONNECTED_TIME	= 1<<16,
 	STATION_INFO_ASSOC_REQ_IES	= 1<<17,
 	STATION_INFO_STA_FLAGS		= 1<<18,
-	STATION_INFO_BEACON_LOSS_COUNT	= 1<<19
+	STATION_INFO_BEACON_LOSS_COUNT	= 1<<19,
+	STATION_INFO_T_OFFSET		= 1<<20,
 };
 
 /**
@@ -643,6 +645,7 @@ struct sta_bss_parameters {
  * @assoc_req_ies_len: Length of assoc_req_ies buffer in octets.
  * @sta_flags: station flags mask & values
  * @beacon_loss_count: Number of times beacon loss event has triggered.
+ * @t_offset: Time offset of the station relative to this host.
  */
 struct station_info {
 	u32 filled;
@@ -671,6 +674,7 @@ struct station_info {
 	size_t assoc_req_ies_len;
 
 	u32 beacon_loss_count;
+	s64 t_offset;
 
 	/*
 	 * Note: Add a new enum station_info_flags value for each new field and
@@ -798,6 +802,8 @@ struct mesh_config {
 	/* ttl used in path selection information elements */
 	u8  element_ttl;
 	bool auto_open_plinks;
+	/* neighbor offset synchronization */
+	u32 dot11MeshNbrOffsetMaxNeighbor;
 	/* HWMP parameters */
 	u8  dot11MeshHWMPmaxPREQretries;
 	u32 path_refresh_time;
@@ -821,6 +827,7 @@ struct mesh_config {
  * struct mesh_setup - 802.11s mesh setup configuration
  * @mesh_id: the mesh ID
  * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
+ * @sync_method: which synchronization method to use
  * @path_sel_proto: which path selection protocol to use
  * @path_metric: which metric to use
  * @ie: vendor information elements (optional)
@@ -834,8 +841,9 @@ struct mesh_config {
 struct mesh_setup {
 	const u8 *mesh_id;
 	u8 mesh_id_len;
-	u8  path_sel_proto;
-	u8  path_metric;
+	u8 sync_method;
+	u8 path_sel_proto;
+	u8 path_metric;
 	const u8 *ie;
 	u8 ie_len;
 	bool is_authenticated;
@@ -845,7 +853,7 @@ struct mesh_setup {
 
 /**
  * struct ieee80211_txq_params - TX queue parameters
- * @queue: TX queue identifier (NL80211_TXQ_Q_*)
+ * @ac: AC identifier
  * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
  * @cwmin: Minimum contention window [a value of the form 2^n-1 in the range
  *	1..32767]
@@ -854,7 +862,7 @@ struct mesh_setup {
  * @aifs: Arbitration interframe space [0..255]
  */
 struct ieee80211_txq_params {
-	enum nl80211_txq_q queue;
+	enum nl80211_ac ac;
 	u16 txop;
 	u16 cwmin;
 	u16 cwmax;
@@ -1336,6 +1344,9 @@ struct cfg80211_gtk_rekey_data {
  *	be %NULL or contain the enabled Wake-on-Wireless triggers that are
  *	configured for the device.
  * @resume: wiphy device needs to be resumed
+ * @set_wakeup: Called when WoWLAN is enabled/disabled, use this callback
+ *	to call device_set_wakeup_enable() to enable/disable wakeup from
+ *	the device.
  *
  * @add_virtual_intf: create a new virtual interface with the given name,
  *	must set the struct wireless_dev's iftype. Beware: You must create
@@ -1507,6 +1518,7 @@ struct cfg80211_gtk_rekey_data {
 struct cfg80211_ops {
 	int	(*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
 	int	(*resume)(struct wiphy *wiphy);
+	void	(*set_wakeup)(struct wiphy *wiphy, bool enabled);
 
 	struct net_device * (*add_virtual_intf)(struct wiphy *wiphy,
 						char *name,
@@ -3343,6 +3355,17 @@ int cfg80211_can_beacon_sec_chan(struct wiphy *wiphy,
 				 enum nl80211_channel_type channel_type);
 
 /*
+ * cfg80211_ch_switch_notify - update wdev channel and notify userspace
+ * @dev: the device which switched channels
+ * @freq: new channel frequency (in MHz)
+ * @type: channel type
+ *
+ * Acquires wdev_lock, so must only be called from sleepable driver context!
+ */
+void cfg80211_ch_switch_notify(struct net_device *dev, int freq,
+			       enum nl80211_channel_type type);
+
+/*
  * cfg80211_calculate_bitrate - calculate actual bitrate (in 100Kbps units)
  * @rate: given rate_info to calculate bitrate from
  *
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 9210bdc..32cd517 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -95,9 +95,11 @@ struct device;
  * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
  */
 enum ieee80211_max_queues {
-	IEEE80211_MAX_QUEUES =		4,
+	IEEE80211_MAX_QUEUES =		16,
 };
 
+#define IEEE80211_INVAL_HW_QUEUE	0xff
+
 /**
  * enum ieee80211_ac_numbers - AC numbers as used in mac80211
  * @IEEE80211_AC_VO: voice
@@ -244,7 +246,7 @@ enum ieee80211_rssi_event {
  * @channel_type: Channel type for this BSS -- the hardware might be
  *	configured for HT40+ while this BSS only uses no-HT, for
  *	example.
- * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
+ * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
  *	This field is only valid when the channel type is one of the HT types.
  * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
  *	implies disabled
@@ -522,7 +524,7 @@ struct ieee80211_tx_rate {
  *
  * @flags: transmit info flags, defined above
  * @band: the band to transmit on (use for checking for races)
- * @antenna_sel_tx: antenna to use, 0 for automatic diversity
+ * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
  * @ack_frame_id: internal frame ID for TX status, used internally
  * @control: union for control data
  * @status: union for status data
@@ -538,7 +540,7 @@ struct ieee80211_tx_info {
 	u32 flags;
 	u8 band;
 
-	u8 antenna_sel_tx;
+	u8 hw_queue;
 
 	u16 ack_frame_id;
 
@@ -564,7 +566,8 @@ struct ieee80211_tx_info {
 			u8 ampdu_ack_len;
 			int ack_signal;
 			u8 ampdu_len;
-			/* 15 bytes free */
+			u8 antenna;
+			/* 14 bytes free */
 		} status;
 		struct {
 			struct ieee80211_tx_rate driver_rates[
@@ -888,6 +891,8 @@ enum ieee80211_vif_flags {
  *	these need to be set (or cleared) when the interface is added
  *	or, if supported by the driver, the interface type is changed
  *	at runtime, mac80211 will never touch this field
+ * @hw_queue: hardware queue for each AC
+ * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
  * @drv_priv: data area for driver use, will always be aligned to
  *	sizeof(void *).
  */
@@ -896,7 +901,12 @@ struct ieee80211_vif {
 	struct ieee80211_bss_conf bss_conf;
 	u8 addr[ETH_ALEN];
 	bool p2p;
+
+	u8 cab_queue;
+	u8 hw_queue[IEEE80211_NUM_ACS];
+
 	u32 driver_flags;
+
 	/* must be last */
 	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
 };
@@ -1174,6 +1184,15 @@ enum sta_notify_cmd {
  * @IEEE80211_HW_SCAN_WHILE_IDLE: The device can do hw scan while
  *	being idle (i.e. mac80211 doesn't have to go idle-off during the
  *	the scan).
+ *
+ * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
+ *	a virtual monitor interface when monitor interfaces are the only
+ *	active interfaces.
+ *
+ * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
+ *	queue mapping in order to use different queues (not just one per AC)
+ *	for different virtual interfaces. See the doc section on HW queue
+ *	control for more details.
  */
 enum ieee80211_hw_flags {
 	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
@@ -1190,13 +1209,13 @@ enum ieee80211_hw_flags {
 	IEEE80211_HW_PS_NULLFUNC_STACK			= 1<<11,
 	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
 	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
-	/* reuse bit 14 */
+	IEEE80211_HW_WANT_MONITOR_VIF			= 1<<14,
 	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
 	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
 	IEEE80211_HW_SUPPORTS_UAPSD			= 1<<17,
 	IEEE80211_HW_REPORTS_TX_ACK_STATUS		= 1<<18,
 	IEEE80211_HW_CONNECTION_MONITOR			= 1<<19,
-	/* reuse bit 20 */
+	IEEE80211_HW_QUEUE_CONTROL			= 1<<20,
 	IEEE80211_HW_SUPPORTS_PER_STA_GTK		= 1<<21,
 	IEEE80211_HW_AP_LINK_PS				= 1<<22,
 	IEEE80211_HW_TX_AMPDU_SETUP_IN_HW		= 1<<23,
@@ -1266,6 +1285,9 @@ enum ieee80211_hw_flags {
  * @max_tx_aggregation_subframes: maximum number of subframes in an
  *	aggregate an HT driver will transmit, used by the peer as a
  *	hint to size its reorder buffer.
+ *
+ * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
+ *	(if %IEEE80211_HW_QUEUE_CONTROL is set)
  */
 struct ieee80211_hw {
 	struct ieee80211_conf conf;
@@ -1286,6 +1308,7 @@ struct ieee80211_hw {
 	u8 max_rate_tries;
 	u8 max_rx_aggregation_subframes;
 	u8 max_tx_aggregation_subframes;
+	u8 offchannel_tx_hw_queue;
 };
 
 /**
@@ -1694,6 +1717,61 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
  */
 
 /**
+ * DOC: HW queue control
+ *
+ * Before HW queue control was introduced, mac80211 only had a single static
+ * assignment of per-interface AC software queues to hardware queues. This
+ * was problematic for a few reasons:
+ * 1) off-channel transmissions might get stuck behind other frames
+ * 2) multiple virtual interfaces couldn't be handled correctly
+ * 3) after-DTIM frames could get stuck behind other frames
+ *
+ * To solve this, hardware typically uses multiple different queues for all
+ * the different usages, and this needs to be propagated into mac80211 so it
+ * won't have the same problem with the software queues.
+ *
+ * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
+ * flag that tells it that the driver implements its own queue control. To do
+ * so, the driver will set up the various queues in each &struct ieee80211_vif
+ * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
+ * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
+ * if necessary will queue the frame on the right software queue that mirrors
+ * the hardware queue.
+ * Additionally, the driver has to then use these HW queue IDs for the queue
+ * management functions (ieee80211_stop_queue() et al.)
+ *
+ * The driver is free to set up the queue mappings as needed, multiple virtual
+ * interfaces may map to the same hardware queues if needed. The setup has to
+ * happen during add_interface or change_interface callbacks. For example, a
+ * driver supporting station+station and station+AP modes might decide to have
+ * 10 hardware queues to handle different scenarios:
+ *
+ * 4 AC HW queues for 1st vif: 0, 1, 2, 3
+ * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
+ * after-DTIM queue for AP:   8
+ * off-channel queue:         9
+ *
+ * It would then set up the hardware like this:
+ *   hw.offchannel_tx_hw_queue = 9
+ *
+ * and the first virtual interface that is added as follows:
+ *   vif.hw_queue[IEEE80211_AC_VO] = 0
+ *   vif.hw_queue[IEEE80211_AC_VI] = 1
+ *   vif.hw_queue[IEEE80211_AC_BE] = 2
+ *   vif.hw_queue[IEEE80211_AC_BK] = 3
+ *   vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
+ * and the second virtual interface with 4-7.
+ *
+ * If queue 6 gets full, for example, mac80211 would only stop the second
+ * virtual interface's BE queue since virtual interface queues are per AC.
+ *
+ * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
+ * whenever the queue is not used (i.e. the interface is not in AP mode) if the
+ * queue could potentially be shared since mac80211 will look at cab_queue when
+ * a queue is stopped/woken even if the interface is not in AP mode.
+ */
+
+/**
  * enum ieee80211_filter_flags - hardware filter flags
  *
  * These flags determine what the filter in hardware should be
@@ -1780,6 +1858,18 @@ enum ieee80211_frame_release_type {
 };
 
 /**
+ * enum ieee80211_rate_control_changed - flags to indicate what changed
+ *
+ * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
+ *	to this station changed.
+ * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
+ */
+enum ieee80211_rate_control_changed {
+	IEEE80211_RC_BW_CHANGED		= BIT(0),
+	IEEE80211_RC_SMPS_CHANGED	= BIT(1),
+};
+
+/**
  * struct ieee80211_ops - callbacks from mac80211 to the driver
  *
  * This structure contains various callbacks that the driver may
@@ -1980,6 +2070,14 @@ enum ieee80211_frame_release_type {
  *	up the list of states.
  *	The callback can sleep.
  *
+ * @sta_rc_update: Notifies the driver of changes to the bitrates that can be
+ *	used to transmit to the station. The changes are advertised with bits
+ *	from &enum ieee80211_rate_control_changed and the values are reflected
+ *	in the station data. This callback should only be used when the driver
+ *	uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
+ *	otherwise the rate control algorithm is notified directly.
+ *	Must be atomic.
+ *
  * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
  *	bursting) for a hardware TX queue.
  *	Returns a negative error code on failure.
@@ -2135,6 +2233,7 @@ struct ieee80211_ops {
 #ifdef CONFIG_PM
 	int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
 	int (*resume)(struct ieee80211_hw *hw);
+	void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
 #endif
 	int (*add_interface)(struct ieee80211_hw *hw,
 			     struct ieee80211_vif *vif);
@@ -2196,8 +2295,12 @@ struct ieee80211_ops {
 			 struct ieee80211_sta *sta,
 			 enum ieee80211_sta_state old_state,
 			 enum ieee80211_sta_state new_state);
+	void (*sta_rc_update)(struct ieee80211_hw *hw,
+			      struct ieee80211_vif *vif,
+			      struct ieee80211_sta *sta,
+			      u32 changed);
 	int (*conf_tx)(struct ieee80211_hw *hw,
-		       struct ieee80211_vif *vif, u16 queue,
+		       struct ieee80211_vif *vif, u16 ac,
 		       const struct ieee80211_tx_queue_params *params);
 	u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
 	void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
@@ -3512,19 +3615,6 @@ void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
 /* Rate control API */
 
 /**
- * enum rate_control_changed - flags to indicate which parameter changed
- *
- * @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have
- *	changed, rate control algorithm can update its internal state if needed.
- * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed, the rate
- *	control algorithm needs to adjust accordingly.
- */
-enum rate_control_changed {
-	IEEE80211_RC_HT_CHANGED		= BIT(0),
-	IEEE80211_RC_SMPS_CHANGED	= BIT(1),
-};
-
-/**
  * struct ieee80211_tx_rate_control - rate control information for/from RC algo
  *
  * @hw: The hardware the algorithm is invoked for.
@@ -3569,9 +3659,8 @@ struct rate_control_ops {
 	void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
 			  struct ieee80211_sta *sta, void *priv_sta);
 	void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
-			    struct ieee80211_sta *sta,
-			    void *priv_sta, u32 changed,
-			    enum nl80211_channel_type oper_chan_type);
+			    struct ieee80211_sta *sta, void *priv_sta,
+			    u32 changed);
 	void (*free_sta)(void *priv, struct ieee80211_sta *sta,
 			 void *priv_sta);
 
@@ -3706,8 +3795,9 @@ void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
 
 void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
 
-int ieee80211_add_srates_ie(struct ieee80211_vif *vif, struct sk_buff *skb);
+int ieee80211_add_srates_ie(struct ieee80211_vif *vif,
+			    struct sk_buff *skb, bool need_basic);
 
 int ieee80211_add_ext_srates_ie(struct ieee80211_vif *vif,
-				struct sk_buff *skb);
+				struct sk_buff *skb, bool need_basic);
 #endif /* MAC80211_H */