diff options
| -rw-r--r-- | drivers/net/e1000e/hw.h | 4 | ||||
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 107 | ||||
| -rw-r--r-- | drivers/net/e1000e/lib.c | 6 |
3 files changed, 110 insertions, 7 deletions
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h index 163c1c0..fd44d9f 100644 --- a/drivers/net/e1000e/hw.h +++ b/drivers/net/e1000e/hw.h @@ -215,6 +215,7 @@ enum e1e_registers { E1000_SWSM = 0x05B50, /* SW Semaphore */ E1000_FWSM = 0x05B54, /* FW Semaphore */ E1000_SWSM2 = 0x05B58, /* Driver-only SW semaphore */ + E1000_CRC_OFFSET = 0x05F50, /* CRC Offset register */ E1000_HICR = 0x08F00, /* Host Interface Control */ }; @@ -302,6 +303,9 @@ enum e1e_registers { #define E1000_KMRNCTRLSTA_REN 0x00200000 #define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */ #define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */ +#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7 +#define E1000_KMRNCTRLSTA_K1_ENABLE 0x140E +#define E1000_KMRNCTRLSTA_K1_DISABLE 0x1400 #define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 #define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Control */ diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 0e0755f..d56c747 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -461,6 +461,95 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter) return 0; } +/** + * e1000_check_for_copper_link_ich8lan - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks to see of the link status of the hardware has changed. If a + * change in link status has been detected, then we read the PHY registers + * to get the current speed/duplex if link exists. + **/ +static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) +{ + struct e1000_mac_info *mac = &hw->mac; + s32 ret_val; + bool link; + + /* + * We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) { + ret_val = 0; + goto out; + } + + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000e_write_kmrn_reg(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + E1000_KMRNCTRLSTA_K1_ENABLE); + if (ret_val) + goto out; + } + + /* + * First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) + goto out; /* No link detected */ + + mac->get_link_status = false; + + if (hw->phy.type == e1000_phy_82578) { + ret_val = e1000_link_stall_workaround_hv(hw); + if (ret_val) + goto out; + } + + /* + * Check if there was DownShift, must be checked + * immediately after link-up + */ + e1000e_check_downshift(hw); + + /* + * If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + /* + * Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + e1000e_config_collision_dist(hw); + + /* + * Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = e1000e_config_fc_after_link_up(hw); + if (ret_val) + hw_dbg(hw, "Error configuring flow control\n"); + +out: + return ret_val; +} + static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; @@ -2224,6 +2313,14 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) } } + /* + * For PCH, this write will make sure that any noise + * will be detected as a CRC error and be dropped rather than show up + * as a bad packet to the DMA engine. + */ + if (hw->mac.type == e1000_pchlan) + ew32(CRC_OFFSET, 0x65656565); + ew32(IMC, 0xffffffff); icr = er32(ICR); @@ -2538,6 +2635,14 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, if (ret_val) return ret_val; + if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) { + ret_val = e1000e_write_kmrn_reg(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + E1000_KMRNCTRLSTA_K1_DISABLE); + if (ret_val) + return ret_val; + } + if ((hw->mac.type == e1000_ich8lan) && (hw->phy.type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { @@ -2984,7 +3089,7 @@ static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw) static struct e1000_mac_operations ich8_mac_ops = { .id_led_init = e1000e_id_led_init, .check_mng_mode = e1000_check_mng_mode_ich8lan, - .check_for_link = e1000e_check_for_copper_link, + .check_for_link = e1000_check_for_copper_link_ich8lan, /* cleanup_led dependent on mac type */ .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan, .get_bus_info = e1000_get_bus_info_ich8lan, diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c index be6d9e9..99ba2b8 100644 --- a/drivers/net/e1000e/lib.c +++ b/drivers/net/e1000e/lib.c @@ -378,12 +378,6 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) mac->get_link_status = 0; - if (hw->phy.type == e1000_phy_82578) { - ret_val = e1000_link_stall_workaround_hv(hw); - if (ret_val) - return ret_val; - } - /* * Check if there was DownShift, must be checked * immediately after link-up |