diff options
-rw-r--r-- | arch/x86/kernel/acpi/boot.c | 65 |
1 files changed, 7 insertions, 58 deletions
diff --git a/arch/x86/kernel/acpi/boot.c b/arch/x86/kernel/acpi/boot.c index 6ee96b5..fb5e882 100644 --- a/arch/x86/kernel/acpi/boot.c +++ b/arch/x86/kernel/acpi/boot.c @@ -1162,22 +1162,9 @@ int mp_register_gsi(struct device *dev, u32 gsi, int triggering, int polarity) { int ioapic; int ioapic_pin; -#ifdef CONFIG_X86_32 -#define MAX_GSI_NUM 4096 -#define IRQ_COMPRESSION_START 64 - - static int pci_irq = IRQ_COMPRESSION_START; - /* - * Mapping between Global System Interrupts, which - * represent all possible interrupts, and IRQs - * assigned to actual devices. - */ - static int gsi_to_irq[MAX_GSI_NUM]; -#else if (acpi_irq_model != ACPI_IRQ_MODEL_IOAPIC) return gsi; -#endif /* Don't set up the ACPI SCI because it's already set up */ if (acpi_gbl_FADT.sci_interrupt == gsi) @@ -1196,66 +1183,28 @@ int mp_register_gsi(struct device *dev, u32 gsi, int triggering, int polarity) gsi = ioapic_renumber_irq(ioapic, gsi); #endif - /* - * Avoid pin reprogramming. PRTs typically include entries - * with redundant pin->gsi mappings (but unique PCI devices); - * we only program the IOAPIC on the first. - */ if (ioapic_pin > MP_MAX_IOAPIC_PIN) { printk(KERN_ERR "Invalid reference to IOAPIC pin " "%d-%d\n", mp_ioapic_routing[ioapic].apic_id, ioapic_pin); return gsi; } + + /* + * Avoid pin reprogramming. PRTs typically include entries + * with redundant pin->gsi mappings (but unique PCI devices); + * we only program the IOAPIC on the first. + */ if (test_bit(ioapic_pin, mp_ioapic_routing[ioapic].pin_programmed)) { pr_debug("Pin %d-%d already programmed\n", mp_ioapic_routing[ioapic].apic_id, ioapic_pin); -#ifdef CONFIG_X86_32 - return (gsi < IRQ_COMPRESSION_START ? gsi : gsi_to_irq[gsi]); -#else return gsi; -#endif } - set_bit(ioapic_pin, mp_ioapic_routing[ioapic].pin_programmed); -#ifdef CONFIG_X86_32 - /* - * For GSI >= 64, use IRQ compression - */ - if ((gsi >= IRQ_COMPRESSION_START) - && (triggering == ACPI_LEVEL_SENSITIVE)) { - /* - * For PCI devices assign IRQs in order, avoiding gaps - * due to unused I/O APIC pins. - */ - int irq = gsi; - if (gsi < MAX_GSI_NUM) { - /* - * Retain the VIA chipset work-around (gsi > 15), but - * avoid a problem where the 8254 timer (IRQ0) is setup - * via an override (so it's not on pin 0 of the ioapic), - * and at the same time, the pin 0 interrupt is a PCI - * type. The gsi > 15 test could cause these two pins - * to be shared as IRQ0, and they are not shareable. - * So test for this condition, and if necessary, avoid - * the pin collision. - */ - gsi = pci_irq++; - /* - * Don't assign IRQ used by ACPI SCI - */ - if (gsi == acpi_gbl_FADT.sci_interrupt) - gsi = pci_irq++; - gsi_to_irq[irq] = gsi; - } else { - printk(KERN_ERR "GSI %u is too high\n", gsi); - return gsi; - } - } -#endif io_apic_set_pci_routing(dev, ioapic, ioapic_pin, gsi, triggering == ACPI_EDGE_SENSITIVE ? 0 : 1, polarity == ACPI_ACTIVE_HIGH ? 0 : 1); + return gsi; } |