diff options
Diffstat (limited to 'arch/arm/mach-at91')
-rw-r--r-- | arch/arm/mach-at91/Kconfig | 20 | ||||
-rw-r--r-- | arch/arm/mach-at91/at91sam9g45_devices.c | 2 | ||||
-rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c | 23 | ||||
-rw-r--r-- | arch/arm/mach-at91/include/mach/cpu.h | 9 |
4 files changed, 36 insertions, 18 deletions
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index e35d54d..2fd8843 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -289,13 +289,6 @@ config MACH_NEOCORE926 help Select this if you are using the Adeneo Neocore 926 board. -config MACH_AT91SAM9G20EK_2MMC - bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots" - depends on ARCH_AT91SAM9G20 - help - Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit - Rev A or B modified for 2 MMC Slots. - endif # ---------------------------------------------------------- @@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" depends on ARCH_AT91SAM9G20 help - Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit + that embeds only one SD/MMC slot. + +config MACH_AT91SAM9G20EK_2MMC + bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit + with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and + onwards. config MACH_CPU9G20 bool "Eukrea CPU9G20 board" @@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD config MTD_NAND_ATMEL_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c index d581cff..332b784 100644 --- a/arch/arm/mach-at91/at91sam9g45_devices.c +++ b/arch/arm/mach-at91/at91sam9g45_devices.c @@ -838,7 +838,7 @@ static void __init at91_add_device_rtt(void) * Watchdog * -------------------------------------------------------------------- */ -#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE) +#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) static struct platform_device at91sam9g45_wdt_device = { .name = "at91_wdt", .id = -1, diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c index a28e53f..a4102d7 100644 --- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c +++ b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c @@ -90,7 +90,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_ATMELMCI) +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -113,7 +113,7 @@ static struct spi_board_info ek_spi_devices[] = { * MACB Ethernet device */ static struct at91_eth_data __initdata ek_macb_data = { - .phy_irq_pin = AT91_PIN_PC12, + .phy_irq_pin = AT91_PIN_PB0, .is_rmii = 1, }; @@ -194,24 +194,27 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin and wp_pin are not connected + * wp_pin is not connected */ #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) static struct mci_platform_data __initdata ek_mmc_data = { .slot[0] = { .bus_width = 4, - .detect_pin = -ENODEV, + .detect_pin = AT91_PIN_PC2, .wp_pin = -ENODEV, }, .slot[1] = { .bus_width = 4, - .detect_pin = -ENODEV, + .detect_pin = AT91_PIN_PC9, .wp_pin = -ENODEV, }, }; #else -static struct amci_platform_data __initdata ek_mmc_data = { +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, /* Only one slot so use slot B */ + .wire4 = 1, + .det_pin = AT91_PIN_PC9, }; #endif @@ -221,13 +224,13 @@ static struct amci_platform_data __initdata ek_mmc_data = { static struct gpio_led ek_leds[] = { { /* "bottom" led, green, userled1 to be defined */ .name = "ds5", - .gpio = AT91_PIN_PB12, + .gpio = AT91_PIN_PB8, .active_low = 1, .default_trigger = "none", }, { /* "power" led, yellow */ .name = "ds1", - .gpio = AT91_PIN_PB13, + .gpio = AT91_PIN_PB9, .default_trigger = "heartbeat", } }; @@ -254,7 +257,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h index 34a9502..c22df30 100644 --- a/arch/arm/mach-at91/include/mach/cpu.h +++ b/arch/arm/mach-at91/include/mach/cpu.h @@ -25,6 +25,8 @@ #define ARCH_ID_AT91SAM9G20 0x019905a0 #define ARCH_ID_AT91SAM9RL64 0x019b03a0 #define ARCH_ID_AT91SAM9G45 0x819b05a0 +#define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */ +#define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */ #define ARCH_ID_AT91CAP9 0x039A03A0 #define ARCH_ID_AT91SAM9XE128 0x329973a0 @@ -41,6 +43,11 @@ static inline unsigned long at91_cpu_identify(void) return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION); } +static inline unsigned long at91_cpu_fully_identify(void) +{ + return at91_sys_read(AT91_DBGU_CIDR); +} + #define ARCH_EXID_AT91SAM9M11 0x00000001 #define ARCH_EXID_AT91SAM9M10 0x00000002 #define ARCH_EXID_AT91SAM9G45 0x00000004 @@ -118,8 +125,10 @@ static inline unsigned long at91cap9_rev_identify(void) #ifdef CONFIG_ARCH_AT91SAM9G45 #define cpu_is_at91sam9g45() (at91_cpu_identify() == ARCH_ID_AT91SAM9G45) +#define cpu_is_at91sam9g45es() (at91_cpu_fully_identify() == ARCH_ID_AT91SAM9G45ES) #else #define cpu_is_at91sam9g45() (0) +#define cpu_is_at91sam9g45es() (0) #endif #ifdef CONFIG_ARCH_AT91CAP9 |