diff options
Diffstat (limited to 'arch/arm/mach-imx')
-rw-r--r-- | arch/arm/mach-imx/headsmp.S | 18 | ||||
-rw-r--r-- | arch/arm/mach-imx/pm-imx6q.c | 15 |
2 files changed, 9 insertions, 24 deletions
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S index 921fc15..a58c8b0 100644 --- a/arch/arm/mach-imx/headsmp.S +++ b/arch/arm/mach-imx/headsmp.S @@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup) #ifdef CONFIG_PM /* - * The following code is located into the .data section. This is to - * allow phys_l2x0_saved_regs to be accessed with a relative load - * as we are running on physical address here. + * The following code must assume it is running from physical address + * where absolute virtual addresses to the data section have to be + * turned into relative ones. */ - .data - .align #ifdef CONFIG_CACHE_L2X0 .macro pl310_resume - ldr r2, phys_l2x0_saved_regs + adr r0, l2x0_saved_regs_offset + ldr r2, [r0] + add r2, r2, r0 ldr r0, [r2, #L2X0_R_PHY_BASE] @ get physical base of l2x0 ldr r1, [r2, #L2X0_R_AUX_CTRL] @ get aux_ctrl value str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl @@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup) str r1, [r0, #L2X0_CTRL] @ re-enable L2 .endm - .globl phys_l2x0_saved_regs -phys_l2x0_saved_regs: - .long 0 +l2x0_saved_regs_offset: + .word l2x0_saved_regs - . + #else .macro pl310_resume .endm diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c index ee42d20..5faba7a 100644 --- a/arch/arm/mach-imx/pm-imx6q.c +++ b/arch/arm/mach-imx/pm-imx6q.c @@ -22,8 +22,6 @@ #include "common.h" #include "hardware.h" -extern unsigned long phys_l2x0_saved_regs; - static int imx6q_suspend_finish(unsigned long val) { cpu_do_idle(); @@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = { void __init imx6q_pm_init(void) { - /* - * The l2x0 core code provides an infrastucture to save and restore - * l2x0 registers across suspend/resume cycle. But because imx6q - * retains L2 content during suspend and needs to resume L2 before - * MMU is enabled, it can only utilize register saving support and - * have to take care of restoring on its own. So we save physical - * address of the data structure used by l2x0 core to save registers, - * and later restore the necessary ones in imx6q resume entry. - */ -#ifdef CONFIG_CACHE_L2X0 - phys_l2x0_saved_regs = __pa(&l2x0_saved_regs); -#endif - suspend_set_ops(&imx6q_pm_ops); } |