diff options
Diffstat (limited to 'arch/arm/mach-orion5x/ts409-setup.c')
| -rw-r--r-- | arch/arm/mach-orion5x/ts409-setup.c | 322 |
1 files changed, 322 insertions, 0 deletions
diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c new file mode 100644 index 0000000..d85588a --- /dev/null +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -0,0 +1,322 @@ +/* + * QNAP TS-409 Board Setup + * + * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> + * + * Copyright (C) 2008 Sylver Bruneau <sylver.bruneau@gmail.com> + * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/leds.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/i2c.h> +#include <linux/serial_reg.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <mach/orion5x.h> +#include "common.h" +#include "mpp.h" +#include "tsx09-common.h" + +/***************************************************************************** + * QNAP TS-409 Info + ****************************************************************************/ + +/* + * QNAP TS-409 hardware : + * - Marvell 88F5281-D0 + * - Marvell 88SX7042 SATA controller (PCIe) + * - Marvell 88E1118 Gigabit Ethernet PHY + * - RTC S35390A (@0x30) on I2C bus + * - 8MB NOR flash + * - 256MB of DDR-2 RAM + */ + +/* + * 8MB NOR flash Device bus boot chip select + */ + +#define QNAP_TS409_NOR_BOOT_BASE 0xff800000 +#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M + +/**************************************************************************** + * 8MiB NOR flash. The struct mtd_partition is not in the same order as the + * partitions on the device because we want to keep compatability with + * existing QNAP firmware. + * + * Layout as used by QNAP: + * [2] 0x00000000-0x00200000 : "Kernel" + * [3] 0x00200000-0x00600000 : "RootFS1" + * [4] 0x00600000-0x00700000 : "RootFS2" + * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) + * [5] 0x00760000-0x00780000 : "U-Boot Config" + * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) + ***************************************************************************/ +static struct mtd_partition qnap_ts409_partitions[] = { + { + .name = "U-Boot", + .size = 0x00080000, + .offset = 0x00780000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "Kernel", + .size = 0x00200000, + .offset = 0, + }, { + .name = "RootFS1", + .size = 0x00400000, + .offset = 0x00200000, + }, { + .name = "RootFS2", + .size = 0x00100000, + .offset = 0x00600000, + }, { + .name = "U-Boot Config", + .size = 0x00020000, + .offset = 0x00760000, + }, { + .name = "NAS Config", + .size = 0x00060000, + .offset = 0x00700000, + .mask_flags = MTD_WRITEABLE, + }, +}; + +static struct physmap_flash_data qnap_ts409_nor_flash_data = { + .width = 1, + .parts = qnap_ts409_partitions, + .nr_parts = ARRAY_SIZE(qnap_ts409_partitions) +}; + +static struct resource qnap_ts409_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = QNAP_TS409_NOR_BOOT_BASE, + .end = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device qnap_ts409_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { .platform_data = &qnap_ts409_nor_flash_data, }, + .num_resources = 1, + .resource = &qnap_ts409_nor_flash_resource, +}; + +/***************************************************************************** + * PCI + ****************************************************************************/ + +static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1) + return irq; + + /* + * PCI isn't used on the TS-409 + */ + return -1; +} + +static struct hw_pci qnap_ts409_pci __initdata = { + .nr_controllers = 2, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = qnap_ts409_pci_map_irq, +}; + +static int __init qnap_ts409_pci_init(void) +{ + if (machine_is_ts409()) + pci_common_init(&qnap_ts409_pci); + + return 0; +} + +subsys_initcall(qnap_ts409_pci_init); + +/***************************************************************************** + * RTC S35390A on I2C bus + ****************************************************************************/ + +#define TS409_RTC_GPIO 10 + +static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { + I2C_BOARD_INFO("s35390a", 0x30), +}; + +/***************************************************************************** + * LEDs attached to GPIO + ****************************************************************************/ + +static struct gpio_led ts409_led_pins[] = { + { + .name = "ts409:red:sata1", + .gpio = 4, + .active_low = 1, + }, { + .name = "ts409:red:sata2", + .gpio = 5, + .active_low = 1, + }, { + .name = "ts409:red:sata3", + .gpio = 6, + .active_low = 1, + }, { + .name = "ts409:red:sata4", + .gpio = 7, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data ts409_led_data = { + .leds = ts409_led_pins, + .num_leds = ARRAY_SIZE(ts409_led_pins), +}; + +static struct platform_device ts409_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ts409_led_data, + }, +}; + +/**************************************************************************** + * GPIO Attached Keys + * Power button is attached to the PIC microcontroller + ****************************************************************************/ + +#define QNAP_TS409_GPIO_KEY_RESET 14 +#define QNAP_TS409_GPIO_KEY_MEDIA 15 + +static struct gpio_keys_button qnap_ts409_buttons[] = { + { + .code = KEY_RESTART, + .gpio = QNAP_TS409_GPIO_KEY_RESET, + .desc = "Reset Button", + .active_low = 1, + }, { + .code = KEY_COPY, + .gpio = QNAP_TS409_GPIO_KEY_MEDIA, + .desc = "USB Copy Button", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data qnap_ts409_button_data = { + .buttons = qnap_ts409_buttons, + .nbuttons = ARRAY_SIZE(qnap_ts409_buttons), +}; + +static struct platform_device qnap_ts409_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &qnap_ts409_button_data, + }, +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode ts409_mpp_modes[] __initdata = { + { 0, MPP_UNUSED }, + { 1, MPP_UNUSED }, + { 2, MPP_UNUSED }, + { 3, MPP_UNUSED }, + { 4, MPP_GPIO }, /* HDD 1 status */ + { 5, MPP_GPIO }, /* HDD 2 status */ + { 6, MPP_GPIO }, /* HDD 3 status */ + { 7, MPP_GPIO }, /* HDD 4 status */ + { 8, MPP_UNUSED }, + { 9, MPP_UNUSED }, + { 10, MPP_GPIO }, /* RTC int */ + { 11, MPP_UNUSED }, + { 12, MPP_UNUSED }, + { 13, MPP_UNUSED }, + { 14, MPP_GPIO }, /* SW_RST */ + { 15, MPP_GPIO }, /* USB copy button */ + { 16, MPP_UART }, /* UART1 RXD */ + { 17, MPP_UART }, /* UART1 TXD */ + { 18, MPP_UNUSED }, + { 19, MPP_UNUSED }, + { -1 }, +}; + +static void __init qnap_ts409_init(void) +{ + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(ts409_mpp_modes); + + /* + * Configure peripherals. + */ + orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE, + QNAP_TS409_NOR_BOOT_SIZE); + platform_device_register(&qnap_ts409_nor_flash); + + orion5x_ehci0_init(); + qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + + qnap_ts409_partitions[5].offset, + qnap_ts409_partitions[5].size); + orion5x_eth_init(&qnap_tsx09_eth_data); + orion5x_i2c_init(); + orion5x_uart0_init(); + orion5x_uart1_init(); + + platform_device_register(&qnap_ts409_button_device); + + /* Get RTC IRQ and register the chip */ + if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) { + if (gpio_direction_input(TS409_RTC_GPIO) == 0) + qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO); + else + gpio_free(TS409_RTC_GPIO); + } + if (qnap_ts409_i2c_rtc.irq == 0) + pr_warning("qnap_ts409_init: failed to get RTC IRQ\n"); + i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); + platform_device_register(&ts409_leds); + + /* register tsx09 specific power-off method */ + pm_power_off = qnap_tsx09_power_off; +} + +MACHINE_START(TS409, "QNAP TS-409") + /* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = qnap_ts409_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = tag_fixup_mem32, +MACHINE_END |