diff options
Diffstat (limited to 'arch')
-rw-r--r-- | arch/avr32/boards/atngw100/setup.c | 7 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 18 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1003.c | 12 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1004.c | 12 | ||||
-rw-r--r-- | arch/avr32/include/asm/atmel-mci.h | 32 | ||||
-rw-r--r-- | arch/avr32/mach-at32ap/at32ap700x.c | 88 |
6 files changed, 139 insertions, 30 deletions
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index b8286f1..f308520 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -53,8 +53,11 @@ static struct spi_board_info spi0_board_info[] __initdata = { }; static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(25), - .wp_pin = GPIO_PIN_PE(0), + .slot[0] = { + .bus_width = 4, + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(0), + }, }; /* diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index dfc3443..4fedbc4 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -264,16 +264,20 @@ void __init setup_board(void) #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + /* MMC card detect requires MACB0 *NOT* be used */ #ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM -static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ - .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ -}; -#define MCI_PDATA &mci0_data + .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ + .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ #else -#define MCI_PDATA NULL + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, #endif /* SW6 for sd{cd,wp} routing */ + }, +}; #endif /* SW2 for MMC signal routing */ @@ -326,7 +330,7 @@ static int __init atstk1002_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0, MCI_PDATA); + at32_add_device_mci(0, &mci0_pdata); #endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c index 0cf6641..acc6123 100644 --- a/arch/avr32/boards/atstk1000/atstk1003.c +++ b/arch/avr32/boards/atstk1000/atstk1003.c @@ -66,6 +66,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { { } }; #endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC static void __init atstk1003_setup_extdac(void) { @@ -154,7 +164,7 @@ static int __init atstk1003_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0, NULL); + at32_add_device_mci(0, &mci0_data); #endif at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c index 50a5273..d6a2d02 100644 --- a/arch/avr32/boards/atstk1000/atstk1004.c +++ b/arch/avr32/boards/atstk1000/atstk1004.c @@ -71,6 +71,16 @@ static struct spi_board_info spi1_board_info[] __initdata = { { } }; #endif +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = -ENODEV, + .wp_pin = -ENODEV, + }, +}; +#endif + #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC static void __init atstk1004_setup_extdac(void) { @@ -137,7 +147,7 @@ static int __init atstk1004_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0, NULL); + at32_add_device_mci(0, &mci0_data); #endif at32_add_device_lcdc(0, &atstk1000_lcdc_data, fbmem_start, fbmem_size, 0); diff --git a/arch/avr32/include/asm/atmel-mci.h b/arch/avr32/include/asm/atmel-mci.h index c2ea6e1..59f3fad 100644 --- a/arch/avr32/include/asm/atmel-mci.h +++ b/arch/avr32/include/asm/atmel-mci.h @@ -1,9 +1,39 @@ #ifndef __ASM_AVR32_ATMEL_MCI_H #define __ASM_AVR32_ATMEL_MCI_H -struct mci_platform_data { +#define ATMEL_MCI_MAX_NR_SLOTS 2 + +struct dma_slave; + +/** + * struct mci_slot_pdata - board-specific per-slot configuration + * @bus_width: Number of data lines wired up the slot + * @detect_pin: GPIO pin wired to the card detect switch + * @wp_pin: GPIO pin wired to the write protect sensor + * + * If a given slot is not present on the board, @bus_width should be + * set to 0. The other fields are ignored in this case. + * + * Any pins that aren't available should be set to a negative value. + * + * Note that support for multiple slots is experimental -- some cards + * might get upset if we don't get the clock management exactly right. + * But in most cases, it should work just fine. + */ +struct mci_slot_pdata { + unsigned int bus_width; int detect_pin; int wp_pin; }; +/** + * struct mci_platform_data - board-specific MMC/SDcard configuration + * @dma_slave: DMA slave interface to use in data transfers, or NULL. + * @slot: Per-slot configuration data. + */ +struct mci_platform_data { + struct dma_slave *dma_slave; + struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS]; +}; + #endif /* __ASM_AVR32_ATMEL_MCI_H */ diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c index e01dbe4..f1b9a3a 100644 --- a/arch/avr32/mach-at32ap/at32ap700x.c +++ b/arch/avr32/mach-at32ap/at32ap700x.c @@ -1272,10 +1272,14 @@ static struct clk atmel_mci0_pclk = { struct platform_device *__init at32_add_device_mci(unsigned int id, struct mci_platform_data *data) { - struct mci_platform_data _data; struct platform_device *pdev; + struct dw_dma_slave *dws; - if (id != 0) + if (id != 0 || !data) + return NULL; + + /* Must have at least one usable slot */ + if (!data->slot[0].bus_width && !data->slot[1].bus_width) return NULL; pdev = platform_device_alloc("atmel_mci", id); @@ -1286,28 +1290,76 @@ at32_add_device_mci(unsigned int id, struct mci_platform_data *data) ARRAY_SIZE(atmel_mci0_resource))) goto fail; - if (!data) { - data = &_data; - memset(data, -1, sizeof(struct mci_platform_data)); - data->detect_pin = GPIO_PIN_NONE; - data->wp_pin = GPIO_PIN_NONE; - } + if (data->dma_slave) + dws = kmemdup(to_dw_dma_slave(data->dma_slave), + sizeof(struct dw_dma_slave), GFP_KERNEL); + else + dws = kzalloc(sizeof(struct dw_dma_slave), GFP_KERNEL); + + dws->slave.dev = &pdev->dev; + dws->slave.dma_dev = &dw_dmac0_device.dev; + dws->slave.reg_width = DMA_SLAVE_WIDTH_32BIT; + dws->cfg_hi = (DWC_CFGH_SRC_PER(0) + | DWC_CFGH_DST_PER(1)); + dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL + | DWC_CFGL_HS_SRC_POL); + + data->dma_slave = &dws->slave; if (platform_device_add_data(pdev, data, sizeof(struct mci_platform_data))) goto fail; - select_peripheral(PA(10), PERIPH_A, 0); /* CLK */ - select_peripheral(PA(11), PERIPH_A, 0); /* CMD */ - select_peripheral(PA(12), PERIPH_A, 0); /* DATA0 */ - select_peripheral(PA(13), PERIPH_A, 0); /* DATA1 */ - select_peripheral(PA(14), PERIPH_A, 0); /* DATA2 */ - select_peripheral(PA(15), PERIPH_A, 0); /* DATA3 */ + /* CLK line is common to both slots */ + select_peripheral(PA(10), PERIPH_A, 0); - if (gpio_is_valid(data->detect_pin)) - at32_select_gpio(data->detect_pin, 0); - if (gpio_is_valid(data->wp_pin)) - at32_select_gpio(data->wp_pin, 0); + switch (data->slot[0].bus_width) { + case 4: + select_peripheral(PA(13), PERIPH_A, 0); /* DATA1 */ + select_peripheral(PA(14), PERIPH_A, 0); /* DATA2 */ + select_peripheral(PA(15), PERIPH_A, 0); /* DATA3 */ + /* fall through */ + case 1: + select_peripheral(PA(11), PERIPH_A, 0); /* CMD */ + select_peripheral(PA(12), PERIPH_A, 0); /* DATA0 */ + + if (gpio_is_valid(data->slot[0].detect_pin)) + at32_select_gpio(data->slot[0].detect_pin, 0); + if (gpio_is_valid(data->slot[0].wp_pin)) + at32_select_gpio(data->slot[0].wp_pin, 0); + break; + case 0: + /* Slot is unused */ + break; + default: + goto fail; + } + + switch (data->slot[1].bus_width) { + case 4: + select_peripheral(PB(8), PERIPH_B, 0); /* DATA1 */ + select_peripheral(PB(9), PERIPH_B, 0); /* DATA2 */ + select_peripheral(PB(10), PERIPH_B, 0); /* DATA3 */ + /* fall through */ + case 1: + select_peripheral(PB(6), PERIPH_B, 0); /* CMD */ + select_peripheral(PB(7), PERIPH_B, 0); /* DATA0 */ + + if (gpio_is_valid(data->slot[1].detect_pin)) + at32_select_gpio(data->slot[1].detect_pin, 0); + if (gpio_is_valid(data->slot[1].wp_pin)) + at32_select_gpio(data->slot[1].wp_pin, 0); + break; + case 0: + /* Slot is unused */ + break; + default: + if (!data->slot[0].bus_width) + goto fail; + + data->slot[1].bus_width = 0; + break; + } atmel_mci0_pclk.dev = &pdev->dev; |