diff options
Diffstat (limited to 'drivers/media/dvb/frontends/mt2060_priv.h')
| -rw-r--r-- | drivers/media/dvb/frontends/mt2060_priv.h | 105 |
1 files changed, 0 insertions, 105 deletions
diff --git a/drivers/media/dvb/frontends/mt2060_priv.h b/drivers/media/dvb/frontends/mt2060_priv.h deleted file mode 100644 index 5eaccde..0000000 --- a/drivers/media/dvb/frontends/mt2060_priv.h +++ /dev/null @@ -1,105 +0,0 @@ -/* - * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" - * - * Copyright (c) 2006 Olivier DANET <odanet@caramail.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= - */ - -#ifndef MT2060_PRIV_H -#define MT2060_PRIV_H - -// Uncomment the #define below to enable spurs checking. The results where quite unconvincing. -// #define MT2060_SPURCHECK - -/* This driver is based on the information available in the datasheet of the - "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map : - - I2C Address : 0x60 - - Reg.No | B7 | B6 | B5 | B4 | B3 | B2 | B1 | B0 | ( defaults ) - -------------------------------------------------------------------------------- - 00 | [ PART ] | [ REV ] | R = 0x63 - 01 | [ LNABAND ] | [ NUM1(5:2) ] | RW = 0x3F - 02 | [ DIV1 ] | RW = 0x74 - 03 | FM1CA | FM1SS | [ NUM1(1:0) ] | [ NUM2(3:0) ] | RW = 0x00 - 04 | NUM2(11:4) ] | RW = 0x08 - 05 | [ DIV2 ] |NUM2(12)| RW = 0x93 - 06 | L1LK | [ TAD1 ] | L2LK | [ TAD2 ] | R - 07 | [ FMF ] | R - 08 | ? | FMCAL | ? | ? | ? | ? | ? | TEMP | R - 09 | 0 | 0 | [ FMGC ] | 0 | GP02 | GP01 | 0 | RW = 0x20 - 0A | ?? - 0B | 0 | 0 | 1 | 1 | 0 | 0 | [ VGAG ] | RW = 0x30 - 0C | V1CSE | 1 | 1 | 1 | 1 | 1 | 1 | 1 | RW = 0xFF - 0D | 1 | 0 | [ V1CS ] | RW = 0xB0 - 0E | ?? - 0F | ?? - 10 | ?? - 11 | [ LOTO ] | 0 | 0 | 1 | 0 | RW = 0x42 - - PART : Part code : 6 for MT2060 - REV : Revision code : 3 for current revision - LNABAND : Input frequency range : ( See code for details ) - NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details ) - FM1CA : Calibration Start Bit - FM1SS : Calibration Single Step bit - L1LK : LO1 Lock Detect - TAD1 : Tune Line ADC ( ? ) - L2LK : LO2 Lock Detect - TAD2 : Tune Line ADC ( ? ) - FMF : Estimated first IF Center frequency Offset ( ? ) - FM1CAL : Calibration done bit - TEMP : On chip temperature sensor - FMCG : Mixer 1 Cap Gain ( ? ) - GP01 / GP02 : Programmable digital outputs. Unconnected pins ? - V1CSE : LO1 VCO Automatic Capacitor Select Enable ( ? ) - V1CS : LO1 Capacitor Selection Value ( ? ) - LOTO : LO Timeout ( ? ) - VGAG : Tuner Output gain -*/ - -#define I2C_ADDRESS 0x60 - -#define REG_PART_REV 0 -#define REG_LO1C1 1 -#define REG_LO1C2 2 -#define REG_LO2C1 3 -#define REG_LO2C2 4 -#define REG_LO2C3 5 -#define REG_LO_STATUS 6 -#define REG_FM_FREQ 7 -#define REG_MISC_STAT 8 -#define REG_MISC_CTRL 9 -#define REG_RESERVED_A 0x0A -#define REG_VGAG 0x0B -#define REG_LO1B1 0x0C -#define REG_LO1B2 0x0D -#define REG_LOTO 0x11 - -#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips - -struct mt2060_priv { - struct mt2060_config *cfg; - struct i2c_adapter *i2c; - - u32 frequency; - u32 bandwidth; - u16 if1_freq; - u8 fmfreq; -}; - -#endif |