diff options
Diffstat (limited to 'drivers/mtd')
50 files changed, 814 insertions, 939 deletions
diff --git a/drivers/mtd/bcm47xxpart.c b/drivers/mtd/bcm47xxpart.c index 9279a91..7a6384b 100644 --- a/drivers/mtd/bcm47xxpart.c +++ b/drivers/mtd/bcm47xxpart.c @@ -27,11 +27,13 @@ /* Magics */ #define BOARD_DATA_MAGIC 0x5246504D /* MPFR */ +#define FACTORY_MAGIC 0x59544346 /* FCTY */ #define POT_MAGIC1 0x54544f50 /* POTT */ #define POT_MAGIC2 0x504f /* OP */ #define ML_MAGIC1 0x39685a42 #define ML_MAGIC2 0x26594131 #define TRX_MAGIC 0x30524448 +#define SQSH_MAGIC 0x71736873 /* shsq */ struct trx_header { uint32_t magic; @@ -71,7 +73,14 @@ static int bcm47xxpart_parse(struct mtd_info *master, /* Alloc */ parts = kzalloc(sizeof(struct mtd_partition) * BCM47XXPART_MAX_PARTS, GFP_KERNEL); + if (!parts) + return -ENOMEM; + buf = kzalloc(BCM47XXPART_BYTES_TO_READ, GFP_KERNEL); + if (!buf) { + kfree(parts); + return -ENOMEM; + } /* Parse block by block looking for magics */ for (offset = 0; offset <= master->size - blocksize; @@ -110,6 +119,13 @@ static int bcm47xxpart_parse(struct mtd_info *master, continue; } + /* Found on Huawei E970 */ + if (buf[0x000 / 4] == FACTORY_MAGIC) { + bcm47xxpart_add_part(&parts[curr_part++], "factory", + offset, MTD_WRITEABLE); + continue; + } + /* POT(TOP) */ if (buf[0x000 / 4] == POT_MAGIC1 && (buf[0x004 / 4] & 0xFFFF) == POT_MAGIC2) { @@ -167,6 +183,13 @@ static int bcm47xxpart_parse(struct mtd_info *master, offset = rounddown(offset + trx->length, blocksize); continue; } + + /* Squashfs on devices not using TRX */ + if (buf[0x000 / 4] == SQSH_MAGIC) { + bcm47xxpart_add_part(&parts[curr_part++], "rootfs", + offset, 0); + continue; + } } /* Look for NVRAM at the end of the last block. */ diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 74ab4b7..0128138 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -95,13 +95,6 @@ config MTD_M25P80 if you want to specify device partitioning or to use a device which doesn't support the JEDEC ID instruction. -config M25PXX_USE_FAST_READ - bool "Use FAST_READ OPCode allowing SPI CLK >= 50MHz" - depends on MTD_M25P80 - default y - help - This option enables FAST_READ access supported by ST M25Pxx. - config MTD_SPEAR_SMI tristate "SPEAR MTD NOR Support through SMI controller" depends on PLAT_SPEAR diff --git a/drivers/mtd/devices/block2mtd.c b/drivers/mtd/devices/block2mtd.c index 5cb4c04..d9fd87a 100644 --- a/drivers/mtd/devices/block2mtd.c +++ b/drivers/mtd/devices/block2mtd.c @@ -20,6 +20,7 @@ #include <linux/mutex.h> #include <linux/mount.h> #include <linux/slab.h> +#include <linux/major.h> /* Info for the block device */ struct block2mtd_dev { diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c index 3e1b0a0..4f091c1 100644 --- a/drivers/mtd/devices/docg3.c +++ b/drivers/mtd/devices/docg3.c @@ -2097,7 +2097,7 @@ notfound: ret = -ENODEV; dev_info(dev, "No supported DiskOnChip found\n"); err_probe: - kfree(cascade->bch); + free_bch(cascade->bch); for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) if (cascade->floors[floor]) doc_release_device(cascade->floors[floor]); diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index 6bc9618..7eda71d 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -78,7 +78,7 @@ /* Define max times to check status register before we give up. */ #define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */ -#define MAX_CMD_SIZE 5 +#define MAX_CMD_SIZE 6 #define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16) @@ -367,10 +367,6 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, spi_message_init(&m); memset(t, 0, (sizeof t)); - /* NOTE: - * OPCODE_FAST_READ (if available) is faster. - * Should add 1 byte DUMMY_BYTE. - */ t[0].tx_buf = flash->command; t[0].len = m25p_cmdsz(flash) + (flash->fast_read ? 1 : 0); spi_message_add_tail(&t[0], &m); @@ -388,11 +384,6 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, return 1; } - /* FIXME switch to OPCODE_FAST_READ. It's required for higher - * clocks; and at this writing, every chip this driver handles - * supports that opcode. - */ - /* Set up the write data buffer. */ opcode = flash->read_opcode; flash->command[0] = opcode; @@ -749,16 +740,19 @@ static const struct spi_device_id m25p_ids[] = { { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) }, /* EON -- en25xxx */ - { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) }, - { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) }, - { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) }, - { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) }, - { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) }, - { "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) }, + { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) }, + { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) }, + { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) }, + { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) }, + { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) }, + { "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) }, + + /* ESMT */ + { "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K) }, /* Everspin */ - { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, M25P_NO_ERASE | M25P_NO_FR) }, - { "mr25h10", CAT25_INFO(128 * 1024, 1, 256, 3, M25P_NO_ERASE | M25P_NO_FR) }, + { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, M25P_NO_ERASE | M25P_NO_FR) }, + { "mr25h10", CAT25_INFO(128 * 1024, 1, 256, 3, M25P_NO_ERASE | M25P_NO_FR) }, /* GigaDevice */ { "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64, SECT_4K) }, @@ -775,6 +769,7 @@ static const struct spi_device_id m25p_ids[] = { { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) }, { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) }, { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) }, + { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) }, { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) }, { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, @@ -783,15 +778,16 @@ static const struct spi_device_id m25p_ids[] = { { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, 0) }, /* Micron */ - { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) }, - { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) }, - { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) }, - { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) }, + { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) }, + { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) }, + { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) }, + { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) }, + { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) }, /* PMC */ - { "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) }, - { "pm25lv010", INFO(0, 0, 32 * 1024, 4, SECT_4K_PMC) }, - { "pm25lq032", INFO(0x7f9d46, 0, 64 * 1024, 64, SECT_4K) }, + { "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) }, + { "pm25lv010", INFO(0, 0, 32 * 1024, 4, SECT_4K_PMC) }, + { "pm25lq032", INFO(0x7f9d46, 0, 64 * 1024, 64, SECT_4K) }, /* Spansion -- single (large) sector size only, at least * for the chips listed here (without boot sectors). @@ -940,12 +936,7 @@ static int m25p_probe(struct spi_device *spi) struct flash_info *info; unsigned i; struct mtd_part_parser_data ppdata; - struct device_node __maybe_unused *np = spi->dev.of_node; - -#ifdef CONFIG_MTD_OF_PARTS - if (!of_device_is_available(np)) - return -ENODEV; -#endif + struct device_node *np = spi->dev.of_node; /* Platform data helps sort out which chip type we have, as * well as how this board partitions it. If we don't have @@ -992,15 +983,13 @@ static int m25p_probe(struct spi_device *spi) } } - flash = kzalloc(sizeof *flash, GFP_KERNEL); + flash = devm_kzalloc(&spi->dev, sizeof(*flash), GFP_KERNEL); if (!flash) return -ENOMEM; - flash->command = kmalloc(MAX_CMD_SIZE + (flash->fast_read ? 1 : 0), - GFP_KERNEL); - if (!flash->command) { - kfree(flash); + + flash->command = devm_kzalloc(&spi->dev, MAX_CMD_SIZE, GFP_KERNEL); + if (!flash->command) return -ENOMEM; - } flash->spi = spi; mutex_init(&flash->lock); @@ -1062,13 +1051,14 @@ static int m25p_probe(struct spi_device *spi) flash->page_size = info->page_size; flash->mtd.writebufsize = flash->page_size; - flash->fast_read = false; - if (np && of_property_read_bool(np, "m25p,fast-read")) + if (np) + /* If we were instantiated by DT, use it */ + flash->fast_read = of_property_read_bool(np, "m25p,fast-read"); + else + /* If we weren't instantiated by DT, default to fast-read */ flash->fast_read = true; -#ifdef CONFIG_M25PXX_USE_FAST_READ - flash->fast_read = true; -#endif + /* Some devices cannot do fast-read, no matter what DT tells us */ if (info->flags & M25P_NO_FR) flash->fast_read = false; @@ -1133,15 +1123,9 @@ static int m25p_probe(struct spi_device *spi) static int m25p_remove(struct spi_device *spi) { struct m25p *flash = spi_get_drvdata(spi); - int status; /* Clean up MTD stuff. */ - status = mtd_device_unregister(&flash->mtd); - if (status == 0) { - kfree(flash->command); - kfree(flash); - } - return 0; + return mtd_device_unregister(&flash->mtd); } diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c index 0e8cbfe..4a47b02 100644 --- a/drivers/mtd/devices/mtd_dataflash.c +++ b/drivers/mtd/devices/mtd_dataflash.c @@ -88,8 +88,6 @@ struct dataflash { uint8_t command[4]; char name[24]; - unsigned partitioned:1; - unsigned short page_offset; /* offset in flash address */ unsigned int page_size; /* of bytes per page */ @@ -881,7 +879,7 @@ static int dataflash_probe(struct spi_device *spi) break; /* obsolete AT45DB1282 not (yet?) supported */ default: - pr_debug("%s: unsupported device (%x)\n", dev_name(&spi->dev), + dev_info(&spi->dev, "unsupported device (%x)\n", status & 0x3c); status = -ENODEV; } diff --git a/drivers/mtd/devices/phram.c b/drivers/mtd/devices/phram.c index 67823de..e1f2aeb 100644 --- a/drivers/mtd/devices/phram.c +++ b/drivers/mtd/devices/phram.c @@ -94,7 +94,7 @@ static void unregister_devices(void) } } -static int register_device(char *name, unsigned long start, unsigned long len) +static int register_device(char *name, phys_addr_t start, size_t len) { struct phram_mtd_list *new; int ret = -ENOMEM; @@ -141,35 +141,35 @@ out0: return ret; } -static int ustrtoul(const char *cp, char **endp, unsigned int base) +static int parse_num64(uint64_t *num64, char *token) { - unsigned long result = simple_strtoul(cp, endp, base); - - switch (**endp) { - case 'G': - result *= 1024; - case 'M': - result *= 1024; - case 'k': - result *= 1024; + size_t len; + int shift = 0; + int ret; + + len = strlen(token); /* By dwmw2 editorial decree, "ki", "Mi" or "Gi" are to be used. */ - if ((*endp)[1] == 'i') - (*endp) += 2; + if (len > 2) { + if (token[len - 1] == 'i') { + switch (token[len - 2]) { + case 'G': + shift += 10; + case 'M': + shift += 10; + case 'k': + shift += 10; + token[len - 2] = 0; + break; + default: + return -EINVAL; + } + } } - return result; -} -static int parse_num32(uint32_t *num32, const char *token) -{ - char *endp; - unsigned long n; + ret = kstrtou64(token, 0, num64); + *num64 <<= shift; - n = ustrtoul(token, &endp, 0); - if (*endp) - return -EINVAL; - - *num32 = n; - return 0; + return ret; } static int parse_name(char **pname, const char *token) @@ -209,19 +209,19 @@ static inline void kill_final_newline(char *str) * This shall contain the module parameter if any. It is of the form: * - phram=<device>,<address>,<size> for module case * - phram.phram=<device>,<address>,<size> for built-in case - * We leave 64 bytes for the device name, 12 for the address and 12 for the + * We leave 64 bytes for the device name, 20 for the address and 20 for the * size. * Example: phram.phram=rootfs,0xa0000000,512Mi */ -static __initdata char phram_paramline[64+12+12]; +static __initdata char phram_paramline[64 + 20 + 20]; static int __init phram_setup(const char *val) { - char buf[64+12+12], *str = buf; + char buf[64 + 20 + 20], *str = buf; char *token[3]; char *name; - uint32_t start; - uint32_t len; + uint64_t start; + uint64_t len; int i, ret; if (strnlen(val, sizeof(buf)) >= sizeof(buf)) @@ -243,13 +243,13 @@ static int __init phram_setup(const char *val) if (ret) return ret; - ret = parse_num32(&start, token[1]); + ret = parse_num64(&start, token[1]); if (ret) { kfree(name); parse_err("illegal start address\n"); } - ret = parse_num32(&len, token[2]); + ret = parse_num64(&len, token[2]); if (ret) { kfree(name); parse_err("illegal device length\n"); @@ -257,7 +257,7 @@ static int __init phram_setup(const char *val) ret = register_device(name, start, len); if (!ret) - pr_info("%s device: %#x at %#x\n", name, len, start); + pr_info("%s device: %#llx at %#llx\n", name, len, start); else kfree(name); diff --git a/drivers/mtd/devices/sst25l.c b/drivers/mtd/devices/sst25l.c index a42f1f0..687bf27 100644 --- a/drivers/mtd/devices/sst25l.c +++ b/drivers/mtd/devices/sst25l.c @@ -364,7 +364,7 @@ static int sst25l_probe(struct spi_device *spi) if (!flash_info) return -ENODEV; - flash = kzalloc(sizeof(struct sst25l_flash), GFP_KERNEL); + flash = devm_kzalloc(&spi->dev, sizeof(*flash), GFP_KERNEL); if (!flash) return -ENOMEM; @@ -402,11 +402,8 @@ static int sst25l_probe(struct spi_device *spi) ret = mtd_device_parse_register(&flash->mtd, NULL, NULL, data ? data->parts : NULL, data ? data->nr_parts : 0); - if (ret) { - kfree(flash); - spi_set_drvdata(spi, NULL); + if (ret) return -ENODEV; - } return 0; } @@ -414,12 +411,8 @@ static int sst25l_probe(struct spi_device *spi) static int sst25l_remove(struct spi_device *spi) { struct sst25l_flash *flash = spi_get_drvdata(spi); - int ret; - ret = mtd_device_unregister(&flash->mtd); - if (ret == 0) - kfree(flash); - return ret; + return mtd_device_unregister(&flash->mtd); } static struct spi_driver sst25l_driver = { diff --git a/drivers/mtd/inftlcore.c b/drivers/mtd/inftlcore.c index 3af3514..b66b541 100644 --- a/drivers/mtd/inftlcore.c +++ b/drivers/mtd/inftlcore.c @@ -50,7 +50,7 @@ static void inftl_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd) struct INFTLrecord *inftl; unsigned long temp; - if (mtd->type != MTD_NANDFLASH || mtd->size > UINT_MAX) + if (!mtd_type_is_nand(mtd) || mtd->size > UINT_MAX) return; /* OK, this is moderately ugly. But probably safe. Alternatives? */ if (memcmp(mtd->name, "DiskOnChip", 10)) diff --git a/drivers/mtd/lpddr/lpddr_cmds.c b/drivers/mtd/lpddr/lpddr_cmds.c index d3cfe26b..2ef19aa 100644 --- a/drivers/mtd/lpddr/lpddr_cmds.c +++ b/drivers/mtd/lpddr/lpddr_cmds.c @@ -703,7 +703,7 @@ static int lpddr_erase(struct mtd_info *mtd, struct erase_info *instr) #define DO_XXLOCK_LOCK 1 #define DO_XXLOCK_UNLOCK 2 -int do_xxlock(struct mtd_info *mtd, loff_t adr, uint32_t len, int thunk) +static int do_xxlock(struct mtd_info *mtd, loff_t adr, uint32_t len, int thunk) { int ret = 0; struct map_info *map = mtd->priv; diff --git a/drivers/mtd/maps/intel_vr_nor.c b/drivers/mtd/maps/intel_vr_nor.c index f581ac1..46d195f 100644 --- a/drivers/mtd/maps/intel_vr_nor.c +++ b/drivers/mtd/maps/intel_vr_nor.c @@ -180,7 +180,6 @@ static void vr_nor_pci_remove(struct pci_dev *dev) { struct vr_nor_mtd *p = pci_get_drvdata(dev); - pci_set_drvdata(dev, NULL); vr_nor_destroy_partitions(p); vr_nor_destroy_mtd_setup(p); vr_nor_destroy_maps(p); diff --git a/drivers/mtd/maps/pci.c b/drivers/mtd/maps/pci.c index c2604f8..36da518 100644 --- a/drivers/mtd/maps/pci.c +++ b/drivers/mtd/maps/pci.c @@ -316,7 +316,6 @@ static void mtd_pci_remove(struct pci_dev *dev) map->exit(dev, map); kfree(map); - pci_set_drvdata(dev, NULL); pci_release_regions(dev); } diff --git a/drivers/mtd/maps/plat-ram.c b/drivers/mtd/maps/plat-ram.c index 6762716..10196f5 100644 --- a/drivers/mtd/maps/plat-ram.c +++ b/drivers/mtd/maps/plat-ram.c @@ -55,7 +55,7 @@ struct platram_info { static inline struct platram_info *to_platram_info(struct platform_device *dev) { - return (struct platram_info *)platform_get_drvdata(dev); + return platform_get_drvdata(dev); } /* platram_setrw @@ -257,21 +257,7 @@ static struct platform_driver platram_driver = { }, }; -/* module init/exit */ - -static int __init platram_init(void) -{ - printk("Generic platform RAM MTD, (c) 2004 Simtec Electronics\n"); - return platform_driver_register(&platram_driver); -} - -static void __exit platram_exit(void) -{ - platform_driver_unregister(&platram_driver); -} - -module_init(platram_init); -module_exit(platram_exit); +module_platform_driver(platram_driver); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); diff --git a/drivers/mtd/maps/scb2_flash.c b/drivers/mtd/maps/scb2_flash.c index c77b68c..3051c4c 100644 --- a/drivers/mtd/maps/scb2_flash.c +++ b/drivers/mtd/maps/scb2_flash.c @@ -212,7 +212,6 @@ static void scb2_flash_remove(struct pci_dev *dev) if (!region_fail) release_mem_region(SCB2_ADDR, SCB2_WINDOW); - pci_set_drvdata(dev, NULL); } static struct pci_device_id scb2_flash_pci_ids[] = { diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c index 2aef5dd..485ea75 100644 --- a/drivers/mtd/mtdblock.c +++ b/drivers/mtd/mtdblock.c @@ -32,6 +32,7 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/blktrans.h> #include <linux/mutex.h> +#include <linux/major.h> struct mtdblk_dev { @@ -373,7 +374,7 @@ static void mtdblock_remove_dev(struct mtd_blktrans_dev *dev) static struct mtd_blktrans_ops mtdblock_tr = { .name = "mtdblock", - .major = 31, + .major = MTD_BLOCK_MAJOR, .part_bits = 0, .blksize = 512, .open = mtdblock_open, diff --git a/drivers/mtd/mtdblock_ro.c b/drivers/mtd/mtdblock_ro.c index 92759a9..fb5dc89 100644 --- a/drivers/mtd/mtdblock_ro.c +++ b/drivers/mtd/mtdblock_ro.c @@ -24,6 +24,7 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/blktrans.h> #include <linux/module.h> +#include <linux/major.h> static int mtdblock_readsect(struct mtd_blktrans_dev *dev, unsigned long block, char *buf) @@ -70,7 +71,7 @@ static void mtdblock_remove_dev(struct mtd_blktrans_dev *dev) static struct mtd_blktrans_ops mtdblock_tr = { .name = "mtdblock", - .major = 31, + .major = MTD_BLOCK_MAJOR, .part_bits = 0, .blksize = 512, .readsect = mtdblock_readsect, diff --git a/drivers/mtd/mtdchar.c b/drivers/mtd/mtdchar.c index 684bfa3..2147e73 100644 --- a/drivers/mtd/mtdchar.c +++ b/drivers/mtd/mtdchar.c @@ -32,6 +32,7 @@ #include <linux/mount.h> #include <linux/blkpg.h> #include <linux/magic.h> +#include <linux/major.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/map.h> @@ -1099,7 +1100,7 @@ static unsigned long mtdchar_get_unmapped_area(struct file *file, return (unsigned long) -EINVAL; ret = mtd_get_unmapped_area(mtd, len, offset, flags); - return ret == -EOPNOTSUPP ? -ENOSYS : ret; + return ret == -EOPNOTSUPP ? -ENODEV : ret; } #endif @@ -1124,9 +1125,9 @@ static int mtdchar_mmap(struct file *file, struct vm_area_struct *vma) #endif return vm_iomap_memory(vma, map->phys, map->size); } - return -ENOSYS; + return -ENODEV; #else - return vma->vm_flags & VM_SHARED ? 0 : -ENOSYS; + return vma->vm_flags & VM_SHARED ? 0 : -EACCES; #endif } diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c index 5e14d54..92311a5 100644 --- a/drivers/mtd/mtdcore.c +++ b/drivers/mtd/mtdcore.c @@ -157,6 +157,9 @@ static ssize_t mtd_type_show(struct device *dev, case MTD_UBIVOLUME: type = "ubi"; break; + case MTD_MLCNANDFLASH: + type = "mlc-nand"; + break; default: type = "unknown"; } diff --git a/drivers/mtd/mtdsuper.c b/drivers/mtd/mtdsuper.c index 334da5f..20c02a3 100644 --- a/drivers/mtd/mtdsuper.c +++ b/drivers/mtd/mtdsuper.c @@ -17,6 +17,7 @@ #include <linux/export.h> #include <linux/ctype.h> #include <linux/slab.h> +#include <linux/major.h> /* * compare superblocks to see if they're equivalent diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index d885298..93ae6a6 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -96,43 +96,15 @@ config MTD_NAND_OMAP2 config MTD_NAND_OMAP_BCH depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3 - tristate "Enable support for hardware BCH error correction" + tristate "Support hardware based BCH error correction" default n select BCH - select BCH_CONST_PARAMS help - Support for hardware BCH error correction. - -choice - prompt "BCH error correction capability" - depends on MTD_NAND_OMAP_BCH - -config MTD_NAND_OMAP_BCH8 - bool "8 bits / 512 bytes (recommended)" - help - Support correcting up to 8 bitflips per 512-byte block. - This will use 13 bytes of spare area per 512 bytes of page data. - This is the recommended mode, as 4-bit mode does not work - on some OMAP3 revisions, due to a hardware bug. - -config MTD_NAND_OMAP_BCH4 - bool "4 bits / 512 bytes" - help - Support correcting up to 4 bitflips per 512-byte block. - This will use 7 bytes of spare area per 512 bytes of page data. - Note that this mode does not work on some OMAP3 revisions, due to a - hardware bug. Please check your OMAP datasheet before selecting this - mode. - -endchoice - -if MTD_NAND_OMAP_BCH -config BCH_CONST_M - default 13 -config BCH_CONST_T - default 4 if MTD_NAND_OMAP_BCH4 - default 8 if MTD_NAND_OMAP_BCH8 -endif + This config enables the ELM hardware engine, which can be used to + locate and correct errors when using BCH ECC scheme. This offloads + the cpu from doing ECC error searching and correction. However some + legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine + so they should not enable this config symbol. config MTD_NAND_IDS tristate diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index bd1ce7d..d78a97d 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -1062,56 +1062,28 @@ static void atmel_pmecc_core_init(struct mtd_info *mtd) } /* - * Get ECC requirement in ONFI parameters, returns -1 if ONFI - * parameters is not supported. - * return 0 if success to get the ECC requirement. - */ -static int get_onfi_ecc_param(struct nand_chip *chip, - int *ecc_bits, int *sector_size) -{ - *ecc_bits = *sector_size = 0; - - if (chip->onfi_params.ecc_bits == 0xff) - /* TODO: the sector_size and ecc_bits need to be find in - * extended ecc parameter, currently we don't support it. - */ - return -1; - - *ecc_bits = chip->onfi_params.ecc_bits; - - /* The default sector size (ecc codeword size) is 512 */ - *sector_size = 512; - - return 0; -} - -/* - * Get ecc requirement from ONFI parameters ecc requirement. + * Get minimum ecc requirements from NAND. * If pmecc-cap, pmecc-sector-size in DTS are not specified, this function - * will set them according to ONFI ecc requirement. Otherwise, use the + * will set them according to minimum ecc requirement. Otherwise, use the * value in DTS file. * return 0 if success. otherwise return error code. */ static int pmecc_choose_ecc(struct atmel_nand_host *host, int *cap, int *sector_size) { - /* Get ECC requirement from ONFI parameters */ - *cap = *sector_size = 0; - if (host->nand_chip.onfi_version) { - if (!get_onfi_ecc_param(&host->nand_chip, cap, sector_size)) - dev_info(host->dev, "ONFI params, minimum required ECC: %d bits in %d bytes\n", + /* Get minimum ECC requirements */ + if (host->nand_chip.ecc_strength_ds) { + *cap = host->nand_chip.ecc_strength_ds; + *sector_size = host->nand_chip.ecc_step_ds; + dev_info(host->dev, "minimum ECC: %d bits in %d bytes\n", *cap, *sector_size); - else - dev_info(host->dev, "NAND chip ECC reqirement is in Extended ONFI parameter, we don't support yet.\n"); } else { - dev_info(host->dev, "NAND chip is not ONFI compliant, assume ecc_bits is 2 in 512 bytes"); - } - if (*cap == 0 && *sector_size == 0) { *cap = 2; *sector_size = 512; + dev_info(host->dev, "can't detect min. ECC, assume 2 bits in 512 bytes\n"); } - /* If dts file doesn't specify then use the one in ONFI parameters */ + /* If device tree doesn't specify, use NAND's minimum ECC parameters */ if (host->pmecc_corr_cap == 0) { /* use the most fitable ecc bits (the near bigger one ) */ if (*cap <= 2) @@ -1449,7 +1421,6 @@ static void atmel_nand_hwctl(struct mtd_info *mtd, int mode) ecc_writel(host->ecc, CR, ATMEL_ECC_RST); } -#if defined(CONFIG_OF) static int atmel_of_init_port(struct atmel_nand_host *host, struct device_node *np) { @@ -1457,7 +1428,7 @@ static int atmel_of_init_port(struct atmel_nand_host *host, u32 offset[2]; int ecc_mode; struct atmel_nand_data *board = &host->board; - enum of_gpio_flags flags; + enum of_gpio_flags flags = 0; if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) { if (val >= 32) { @@ -1540,13 +1511,6 @@ static int atmel_of_init_port(struct atmel_nand_host *host, return 0; } -#else -static int atmel_of_init_port(struct atmel_nand_host *host, - struct device_node *np) -{ - return -EINVAL; -} -#endif static int atmel_hw_nand_init_params(struct platform_device *pdev, struct atmel_nand_host *host) @@ -2019,7 +1983,8 @@ static int atmel_nand_probe(struct platform_device *pdev) mtd = &host->mtd; nand_chip = &host->nand_chip; host->dev = &pdev->dev; - if (pdev->dev.of_node) { + if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) { + /* Only when CONFIG_OF is enabled of_node can be parsed */ res = atmel_of_init_port(host, pdev->dev.of_node); if (res) goto err_nand_ioremap; @@ -2177,7 +2142,6 @@ err_no_card: if (host->dma_chan) dma_release_channel(host->dma_chan); err_nand_ioremap: - platform_driver_unregister(&atmel_nand_nfc_driver); return res; } @@ -2207,14 +2171,12 @@ static int atmel_nand_remove(struct platform_device *pdev) return 0; } -#if defined(CONFIG_OF) static const struct of_device_id atmel_nand_dt_ids[] = { { .compatible = "atmel,at91rm9200-nand" }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, atmel_nand_dt_ids); -#endif static int atmel_nand_nfc_probe(struct platform_device *pdev) { @@ -2253,12 +2215,11 @@ static int atmel_nand_nfc_probe(struct platform_device *pdev) return 0; } -#if defined(CONFIG_OF) -static struct of_device_id atmel_nand_nfc_match[] = { +static const struct of_device_id atmel_nand_nfc_match[] = { { .compatible = "atmel,sama5d3-nfc" }, { /* sentinel */ } }; -#endif +MODULE_DEVICE_TABLE(of, atmel_nand_nfc_match); static struct platform_driver atmel_nand_nfc_driver = { .driver = { diff --git a/drivers/mtd/nand/bcm47xxnflash/main.c b/drivers/mtd/nand/bcm47xxnflash/main.c index 7bae569..1074459 100644 --- a/drivers/mtd/nand/bcm47xxnflash/main.c +++ b/drivers/mtd/nand/bcm47xxnflash/main.c @@ -29,11 +29,9 @@ static int bcm47xxnflash_probe(struct platform_device *pdev) struct bcm47xxnflash *b47n; int err = 0; - b47n = kzalloc(sizeof(*b47n), GFP_KERNEL); - if (!b47n) { - err = -ENOMEM; - goto out; - } + b47n = devm_kzalloc(&pdev->dev, sizeof(*b47n), GFP_KERNEL); + if (!b47n) + return -ENOMEM; b47n->nand_chip.priv = b47n; b47n->mtd.owner = THIS_MODULE; @@ -48,22 +46,16 @@ static int bcm47xxnflash_probe(struct platform_device *pdev) } if (err) { pr_err("Initialization failed: %d\n", err); - goto err_init; + return err; } err = mtd_device_parse_register(&b47n->mtd, probes, NULL, NULL, 0); if (err) { pr_err("Failed to register MTD device: %d\n", err); - goto err_dev_reg; + return err; } return 0; - -err_dev_reg: -err_init: - kfree(b47n); -out: - return err; } static int bcm47xxnflash_remove(struct platform_device *pdev) @@ -85,22 +77,4 @@ static struct platform_driver bcm47xxnflash_driver = { }, }; -static int __init bcm47xxnflash_init(void) -{ - int err; - - err = platform_driver_register(&bcm47xxnflash_driver); - if (err) - pr_err("Failed to register bcm47xx nand flash driver: %d\n", - err); - - return err; -} - -static void __exit bcm47xxnflash_exit(void) -{ - platform_driver_unregister(&bcm47xxnflash_driver); -} - -module_init(bcm47xxnflash_init); -module_exit(bcm47xxnflash_exit); +module_platform_driver(bcm47xxnflash_driver); diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 2ed2bb3..370b9dd 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -1394,7 +1394,7 @@ static struct nand_bbt_descr bbt_mirror_descr = { }; /* initialize driver data structures */ -void denali_drv_init(struct denali_nand_info *denali) +static void denali_drv_init(struct denali_nand_info *denali) { denali->idx = 0; @@ -1520,7 +1520,7 @@ int denali_init(struct denali_nand_info *denali) * so just let controller do 15bit ECC for MLC and 8bit ECC for * SLC if possible. * */ - if (denali->nand.cellinfo & NAND_CI_CELLTYPE_MSK && + if (!nand_is_slc(&denali->nand) && (denali->mtd.oobsize > (denali->bbtskipbytes + ECC_15BITS * (denali->mtd.writesize / ECC_SECTOR_SIZE)))) { diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/denali_pci.c index e3e4662..033f177 100644 --- a/drivers/mtd/nand/denali_pci.c +++ b/drivers/mtd/nand/denali_pci.c @@ -119,7 +119,6 @@ static void denali_pci_remove(struct pci_dev *dev) iounmap(denali->flash_mem); pci_release_regions(dev); pci_disable_device(dev); - pci_set_drvdata(dev, NULL); kfree(denali); } diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c index eaa3c29..b68a495 100644 --- a/drivers/mtd/nand/diskonchip.c +++ b/drivers/mtd/nand/diskonchip.c @@ -38,7 +38,7 @@ #define CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS 0 #endif -static unsigned long __initdata doc_locations[] = { +static unsigned long doc_locations[] __initdata = { #if defined (__alpha__) || defined(__i386__) || defined(__x86_64__) #ifdef CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH 0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000, diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c index 548db23..bd1cb67 100644 --- a/drivers/mtd/nand/docg4.c +++ b/drivers/mtd/nand/docg4.c @@ -44,6 +44,7 @@ #include <linux/mtd/nand.h> #include <linux/bch.h> #include <linux/bitrev.h> +#include <linux/jiffies.h> /* * In "reliable mode" consecutive 2k pages are used in parallel (in some @@ -269,7 +270,7 @@ static int poll_status(struct docg4_priv *doc) */ uint16_t flash_status; - unsigned int timeo; + unsigned long timeo; void __iomem *docptr = doc->virtadr; dev_dbg(doc->dev, "%s...\n", __func__); @@ -277,22 +278,18 @@ static int poll_status(struct docg4_priv *doc) /* hardware quirk requires reading twice initially */ flash_status = readw(docptr + DOC_FLASHCONTROL); - timeo = 1000; + timeo = jiffies + msecs_to_jiffies(200); /* generous timeout */ do { cpu_relax(); flash_status = readb(docptr + DOC_FLASHCONTROL); - } while (!(flash_status & DOC_CTRL_FLASHREADY) && --timeo); + } while (!(flash_status & DOC_CTRL_FLASHREADY) && + time_before(jiffies, timeo)); - - if (!timeo) { + if (unlikely(!(flash_status & DOC_CTRL_FLASHREADY))) { dev_err(doc->dev, "%s: timed out!\n", __func__); return NAND_STATUS_FAIL; } - if (unlikely(timeo < 50)) - dev_warn(doc->dev, "%s: nearly timed out; %d remaining\n", - __func__, timeo); - return 0; } @@ -1239,7 +1236,6 @@ static void __init init_mtd_structs(struct mtd_info *mtd) nand->block_markbad = docg4_block_markbad; nand->read_buf = docg4_read_buf; nand->write_buf = docg4_write_buf16; - nand->scan_bbt = nand_default_bbt; nand->erase_cmd = docg4_erase_block; nand->ecc.read_page = docg4_read_page; nand->ecc.write_page = docg4_write_page; diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index e59c886..c966fc7 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -651,8 +651,6 @@ static int fsl_elbc_chip_init_tail(struct mtd_info *mtd) chip->page_shift); dev_dbg(priv->dev, "fsl_elbc_init: nand->phys_erase_shift = %d\n", chip->phys_erase_shift); - dev_dbg(priv->dev, "fsl_elbc_init: nand->ecclayout = %p\n", - chip->ecclayout); dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.mode = %d\n", chip->ecc.mode); dev_dbg(priv->dev, "fsl_elbc_init: nand->ecc.steps = %d\n", diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index 2730c78..4335577 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -136,6 +136,69 @@ static struct nand_ecclayout oob_4096_ecc8 = { .oobfree = { {2, 6}, {136, 82} }, }; +/* 8192-byte page size with 4-bit ECC */ +static struct nand_ecclayout oob_8192_ecc4 = { + .eccbytes = 128, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + }, + .oobfree = { {2, 6}, {136, 208} }, +}; + +/* 8192-byte page size with 8-bit ECC -- requires 218-byte OOB */ +static struct nand_ecclayout oob_8192_ecc8 = { + .eccbytes = 256, + .eccpos = { + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 64, 65, 66, 67, 68, 69, 70, 71, + 72, 73, 74, 75, 76, 77, 78, 79, + 80, 81, 82, 83, 84, 85, 86, 87, + 88, 89, 90, 91, 92, 93, 94, 95, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127, + 128, 129, 130, 131, 132, 133, 134, 135, + 136, 137, 138, 139, 140, 141, 142, 143, + 144, 145, 146, 147, 148, 149, 150, 151, + 152, 153, 154, 155, 156, 157, 158, 159, + 160, 161, 162, 163, 164, 165, 166, 167, + 168, 169, 170, 171, 172, 173, 174, 175, + 176, 177, 178, 179, 180, 181, 182, 183, + 184, 185, 186, 187, 188, 189, 190, 191, + 192, 193, 194, 195, 196, 197, 198, 199, + 200, 201, 202, 203, 204, 205, 206, 207, + 208, 209, 210, 211, 212, 213, 214, 215, + 216, 217, 218, 219, 220, 221, 222, 223, + 224, 225, 226, 227, 228, 229, 230, 231, + 232, 233, 234, 235, 236, 237, 238, 239, + 240, 241, 242, 243, 244, 245, 246, 247, + 248, 249, 250, 251, 252, 253, 254, 255, + 256, 257, 258, 259, 260, 261, 262, 263, + }, + .oobfree = { {2, 6}, {264, 80} }, +}; /* * Generic flash bbt descriptors @@ -442,20 +505,29 @@ static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command, if (mtd->writesize > 512) { nand_fcr0 = (NAND_CMD_SEQIN << IFC_NAND_FCR0_CMD0_SHIFT) | - (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD1_SHIFT); + (NAND_CMD_STATUS << IFC_NAND_FCR0_CMD1_SHIFT) | + (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD2_SHIFT); iowrite32be( - (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | - (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | - (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | - (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP3_SHIFT) | - (IFC_FIR_OP_CW1 << IFC_NAND_FIR0_OP4_SHIFT), - &ifc->ifc_nand.nand_fir0); + (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) | + (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP3_SHIFT) | + (IFC_FIR_OP_CMD2 << IFC_NAND_FIR0_OP4_SHIFT), + &ifc->ifc_nand.nand_fir0); + iowrite32be( + (IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP7_SHIFT), + &ifc->ifc_nand.nand_fir1); } else { nand_fcr0 = ((NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD1_SHIFT) | (NAND_CMD_SEQIN << - IFC_NAND_FCR0_CMD2_SHIFT)); + IFC_NAND_FCR0_CMD2_SHIFT) | + (NAND_CMD_STATUS << + IFC_NAND_FCR0_CMD3_SHIFT)); iowrite32be( (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) | @@ -464,8 +536,13 @@ static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command, (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP3_SHIFT) | (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP4_SHIFT), &ifc->ifc_nand.nand_fir0); - iowrite32be(IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT, - &ifc->ifc_nand.nand_fir1); + iowrite32be( + (IFC_FIR_OP_CMD1 << IFC_NAND_FIR1_OP5_SHIFT) | + (IFC_FIR_OP_CW3 << IFC_NAND_FIR1_OP6_SHIFT) | + (IFC_FIR_OP_RDSTAT << + IFC_NAND_FIR1_OP7_SHIFT) | + (IFC_FIR_OP_NOP << IFC_NAND_FIR1_OP8_SHIFT), + &ifc->ifc_nand.nand_fir1); if (column >= mtd->writesize) nand_fcr0 |= @@ -719,8 +796,6 @@ static int fsl_ifc_chip_init_tail(struct mtd_info *mtd) chip->page_shift); dev_dbg(priv->dev, "%s: nand->phys_erase_shift = %d\n", __func__, chip->phys_erase_shift); - dev_dbg(priv->dev, "%s: nand->ecclayout = %p\n", __func__, - chip->ecclayout); dev_dbg(priv->dev, "%s: nand->ecc.mode = %d\n", __func__, chip->ecc.mode); dev_dbg(priv->dev, "%s: nand->ecc.steps = %d\n", __func__, @@ -873,11 +948,25 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) } else { layout = &oob_4096_ecc8; chip->ecc.bytes = 16; + chip->ecc.strength = 8; } priv->bufnum_mask = 1; break; + case CSOR_NAND_PGS_8K: + if ((csor & CSOR_NAND_ECC_MODE_MASK) == + CSOR_NAND_ECC_MODE_4) { + layout = &oob_8192_ecc4; + } else { + layout = &oob_8192_ecc8; + chip->ecc.bytes = 16; + chip->ecc.strength = 8; + } + + priv->bufnum_mask = 0; + break; + default: dev_err(priv->dev, "bad csor %#x: bad page size\n", csor); return -ENODEV; @@ -908,7 +997,6 @@ static int fsl_ifc_chip_remove(struct fsl_ifc_mtd *priv) iounmap(priv->vbase); ifc_nand_ctrl->chips[priv->bank] = NULL; - dev_set_drvdata(priv->dev, NULL); return 0; } @@ -1083,25 +1171,7 @@ static struct platform_driver fsl_ifc_nand_driver = { .remove = fsl_ifc_nand_remove, }; -static int __init fsl_ifc_nand_init(void) -{ - int ret; - - ret = platform_driver_register(&fsl_ifc_nand_driver); - if (ret) - printk(KERN_ERR "fsl-ifc: Failed to register platform" - "driver\n"); - - return ret; -} - -static void __exit fsl_ifc_nand_exit(void) -{ - platform_driver_unregister(&fsl_ifc_nand_driver); -} - -module_init(fsl_ifc_nand_init); -module_exit(fsl_ifc_nand_exit); +module_platform_driver(fsl_ifc_nand_driver); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Freescale"); diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c index 4f8857f..aaced29 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -187,6 +187,12 @@ int gpmi_init(struct gpmi_nand_data *this) /* Select BCH ECC. */ writel(BM_GPMI_CTRL1_BCH_MODE, r->gpmi_regs + HW_GPMI_CTRL1_SET); + /* + * Decouple the chip select from dma channel. We use dma0 for all + * the chips. + */ + writel(BM_GPMI_CTRL1_DECOUPLE_CS, r->gpmi_regs + HW_GPMI_CTRL1_SET); + gpmi_disable_clk(this); return 0; err_out: @@ -1073,6 +1079,13 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) mask = MX23_BM_GPMI_DEBUG_READY0 << chip; reg = readl(r->gpmi_regs + HW_GPMI_DEBUG); } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6Q(this)) { + /* + * In the imx6, all the ready/busy pins are bound + * together. So we only need to check chip 0. + */ + if (GPMI_IS_MX6Q(this)) + chip = 0; + /* MX28 shares the same R/B register as MX6Q. */ mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip); reg = readl(r->gpmi_regs + HW_GPMI_STAT); diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index a9830ff..dabbc14 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -45,7 +45,10 @@ static struct nand_bbt_descr gpmi_bbt_descr = { .pattern = scan_ff_pattern }; -/* We will use all the (page + OOB). */ +/* + * We may change the layout if we can get the ECC info from the datasheet, + * else we will use all the (page + OOB). + */ static struct nand_ecclayout gpmi_hw_ecclayout = { .eccbytes = 0, .eccpos = { 0, }, @@ -354,9 +357,8 @@ int common_nfc_set_geometry(struct gpmi_nand_data *this) struct dma_chan *get_dma_chan(struct gpmi_nand_data *this) { - int chipnr = this->current_chip; - - return this->dma_chans[chipnr]; + /* We use the DMA channel 0 to access all the nand chips. */ + return this->dma_chans[0]; } /* Can we use the upper's buffer directly for DMA? */ @@ -392,8 +394,6 @@ static void dma_irq_callback(void *param) struct gpmi_nand_data *this = param; struct completion *dma_c = &this->dma_done; - complete(dma_c); - switch (this->dma_type) { case DMA_FOR_COMMAND: dma_unmap_sg(this->dev, &this->cmd_sgl, 1, DMA_TO_DEVICE); @@ -418,6 +418,8 @@ static void dma_irq_callback(void *param) default: pr_err("in wrong DMA operation.\n"); } + + complete(dma_c); } int start_dma_without_bch_irq(struct gpmi_nand_data *this, @@ -1263,14 +1265,22 @@ static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, static int gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - /* - * The BCH will use all the (page + oob). - * Our gpmi_hw_ecclayout can only prohibit the JFFS2 to write the oob. - * But it can not stop some ioctls such MEMWRITEOOB which uses - * MTD_OPS_PLACE_OOB. So We have to implement this function to prohibit - * these ioctls too. - */ - return -EPERM; + struct nand_oobfree *of = mtd->ecclayout->oobfree; + int status = 0; + + /* Do we have available oob area? */ + if (!of->length) + return -EPERM; + + if (!nand_is_slc(chip)) + return -EPERM; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of->offset, page); + chip->write_buf(mtd, chip->oob_poi + of->offset, of->length); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + return status & NAND_STATUS_FAIL ? -EIO : 0; } static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs) @@ -1568,8 +1578,6 @@ static int gpmi_set_geometry(struct gpmi_nand_data *this) static int gpmi_pre_bbt_scan(struct gpmi_nand_data *this) { - int ret; - /* Set up swap_block_mark, must be set before the gpmi_set_geometry() */ if (GPMI_IS_MX23(this)) this->swap_block_mark = false; @@ -1577,12 +1585,8 @@ static int gpmi_pre_bbt_scan(struct gpmi_nand_data *this) this->swap_block_mark = true; /* Set up the medium geometry */ - ret = gpmi_set_geometry(this); - if (ret) - return ret; + return gpmi_set_geometry(this); - /* NAND boot init, depends on the gpmi_set_geometry(). */ - return nand_boot_init(this); } static void gpmi_nfc_exit(struct gpmi_nand_data *this) @@ -1664,7 +1668,7 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this) if (ret) goto err_out; - ret = nand_scan_ident(mtd, 1, NULL); + ret = nand_scan_ident(mtd, GPMI_IS_MX6Q(this) ? 2 : 1, NULL); if (ret) goto err_out; @@ -1672,10 +1676,16 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this) if (ret) goto err_out; + chip->options |= NAND_SKIP_BBTSCAN; ret = nand_scan_tail(mtd); if (ret) goto err_out; + ret = nand_boot_init(this); + if (ret) + goto err_out; + chip->scan_bbt(mtd); + ppdata.of_node = this->pdev->dev.of_node; ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); if (ret) @@ -1691,19 +1701,19 @@ static const struct platform_device_id gpmi_ids[] = { { .name = "imx23-gpmi-nand", .driver_data = IS_MX23, }, { .name = "imx28-gpmi-nand", .driver_data = IS_MX28, }, { .name = "imx6q-gpmi-nand", .driver_data = IS_MX6Q, }, - {}, + {} }; static const struct of_device_id gpmi_nand_id_table[] = { { .compatible = "fsl,imx23-gpmi-nand", - .data = (void *)&gpmi_ids[IS_MX23] + .data = (void *)&gpmi_ids[IS_MX23], }, { .compatible = "fsl,imx28-gpmi-nand", - .data = (void *)&gpmi_ids[IS_MX28] + .data = (void *)&gpmi_ids[IS_MX28], }, { .compatible = "fsl,imx6q-gpmi-nand", - .data = (void *)&gpmi_ids[IS_MX6Q] + .data = (void *)&gpmi_ids[IS_MX6Q], }, {} }; MODULE_DEVICE_TABLE(of, gpmi_nand_id_table); @@ -1722,7 +1732,7 @@ static int gpmi_nand_probe(struct platform_device *pdev) return -ENODEV; } - this = kzalloc(sizeof(*this), GFP_KERNEL); + this = devm_kzalloc(&pdev->dev, sizeof(*this), GFP_KERNEL); if (!this) { pr_err("Failed to allocate per-device memory\n"); return -ENOMEM; @@ -1752,7 +1762,6 @@ exit_nfc_init: release_resources(this); exit_acquire_resources: dev_err(this->dev, "driver registration failed: %d\n", ret); - kfree(this); return ret; } @@ -1763,7 +1772,6 @@ static int gpmi_nand_remove(struct platform_device *pdev) gpmi_nfc_exit(this); release_resources(this); - kfree(this); return 0; } diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h index 53397cc..82114cd 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h +++ b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h @@ -108,6 +108,9 @@ #define HW_GPMI_CTRL1_CLR 0x00000068 #define HW_GPMI_CTRL1_TOG 0x0000006c +#define BP_GPMI_CTRL1_DECOUPLE_CS 24 +#define BM_GPMI_CTRL1_DECOUPLE_CS (1 << BP_GPMI_CTRL1_DECOUPLE_CS) + #define BP_GPMI_CTRL1_WRN_DLY_SEL 22 #define BM_GPMI_CTRL1_WRN_DLY_SEL (0x3 << BP_GPMI_CTRL1_WRN_DLY_SEL) #define BF_GPMI_CTRL1_WRN_DLY_SEL(v) \ diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c index f4dd2a8..327d96c 100644 --- a/drivers/mtd/nand/lpc32xx_mlc.c +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -905,7 +905,7 @@ static struct platform_driver lpc32xx_nand_driver = { .driver = { .name = DRV_NAME, .owner = THIS_MODULE, - .of_match_table = of_match_ptr(lpc32xx_nand_match), + .of_match_table = lpc32xx_nand_match, }, }; diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/lpc32xx_slc.c index add7570..23e6974 100644 --- a/drivers/mtd/nand/lpc32xx_slc.c +++ b/drivers/mtd/nand/lpc32xx_slc.c @@ -893,7 +893,6 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) /* Avoid extra scan if using BBT, setup BBT support */ if (host->ncfg->use_bbt) { - chip->options |= NAND_SKIP_BBTSCAN; chip->bbt_options |= NAND_BBT_USE_FLASH; /* @@ -915,13 +914,6 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) goto err_exit3; } - /* Standard layout in FLASH for bad block tables */ - if (host->ncfg->use_bbt) { - if (nand_default_bbt(mtd) < 0) - dev_err(&pdev->dev, - "Error initializing default bad block tables\n"); - } - mtd->name = "nxp_lpc3220_slc"; ppdata.of_node = pdev->dev.of_node; res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts, @@ -1023,7 +1015,7 @@ static struct platform_driver lpc32xx_nand_driver = { .driver = { .name = LPC32XX_MODNAME, .owner = THIS_MODULE, - .of_match_table = of_match_ptr(lpc32xx_nand_match), + .of_match_table = lpc32xx_nand_match, }, }; diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index ce8242b..4edea7f 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -32,6 +32,7 @@ #include <linux/io.h> #include <linux/irq.h> #include <linux/completion.h> +#include <linux/of.h> #include <linux/of_device.h> #include <linux/of_mtd.h> @@ -1507,7 +1508,7 @@ static int mxcnd_probe(struct platform_device *pdev) host->devtype_data->irq_control(host, 0); err = devm_request_irq(&pdev->dev, host->irq, mxc_nfc_irq, - IRQF_DISABLED, DRIVER_NAME, host); + 0, DRIVER_NAME, host); if (err) return err; diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index d340b2f..bd39f7b 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2912,12 +2912,13 @@ static int nand_flash_detect_ext_param_page(struct mtd_info *mtd, /* get the info we want. */ ecc = (struct onfi_ext_ecc_info *)cursor; - if (ecc->codeword_size) { - chip->ecc_strength_ds = ecc->ecc_bits; - chip->ecc_step_ds = 1 << ecc->codeword_size; + if (!ecc->codeword_size) { + pr_debug("Invalid codeword size\n"); + goto ext_out; } - pr_info("ONFI extended param page detected.\n"); + chip->ecc_strength_ds = ecc->ecc_bits; + chip->ecc_step_ds = 1 << ecc->codeword_size; ret = 0; ext_out: @@ -2935,29 +2936,34 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, int i; int val; - /* ONFI need to be probed in 8 bits mode, and 16 bits should be selected with NAND_BUSWIDTH_AUTO */ - if (chip->options & NAND_BUSWIDTH_16) { - pr_err("Trying ONFI probe in 16 bits mode, aborting !\n"); - return 0; - } /* Try ONFI for unknown chip or LP */ chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1); if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' || chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I') return 0; + /* + * ONFI must be probed in 8-bit mode or with NAND_BUSWIDTH_AUTO, not + * with NAND_BUSWIDTH_16 + */ + if (chip->options & NAND_BUSWIDTH_16) { + pr_err("ONFI cannot be probed in 16-bit mode; aborting\n"); + return 0; + } + chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); for (i = 0; i < 3; i++) { chip->read_buf(mtd, (uint8_t *)p, sizeof(*p)); if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) == le16_to_cpu(p->crc)) { - pr_info("ONFI param page %d valid\n", i); break; } } - if (i == 3) + if (i == 3) { + pr_err("Could not find valid ONFI parameter page; aborting\n"); return 0; + } /* Check version */ val = le16_to_cpu(p->revision); @@ -2981,11 +2987,23 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, sanitize_string(p->model, sizeof(p->model)); if (!mtd->name) mtd->name = p->model; + mtd->writesize = le32_to_cpu(p->byte_per_page); - mtd->erasesize = le32_to_cpu(p->pages_per_block) * mtd->writesize; + + /* + * pages_per_block and blocks_per_lun may not be a power-of-2 size + * (don't ask me who thought of this...). MTD assumes that these + * dimensions will be power-of-2, so just truncate the remaining area. + */ + mtd->erasesize = 1 << (fls(le32_to_cpu(p->pages_per_block)) - 1); + mtd->erasesize *= mtd->writesize; + mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page); - chip->chipsize = le32_to_cpu(p->blocks_per_lun); + + /* See erasesize comment */ + chip->chipsize = 1 << (fls(le32_to_cpu(p->blocks_per_lun)) - 1); chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count; + chip->bits_per_cell = p->bits_per_cell; if (onfi_feature(chip) & ONFI_FEATURE_16_BIT_BUS) *busw = NAND_BUSWIDTH_16; @@ -3009,10 +3027,11 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, /* The Extended Parameter Page is supported since ONFI 2.1. */ if (nand_flash_detect_ext_param_page(mtd, chip, p)) - pr_info("Failed to detect the extended param page.\n"); + pr_warn("Failed to detect ONFI extended param page\n"); + } else { + pr_warn("Could not retrieve ONFI ECC requirements\n"); } - pr_info("ONFI flash detected\n"); return 1; } @@ -3075,6 +3094,16 @@ static int nand_id_len(u8 *id_data, int arrlen) return arrlen; } +/* Extract the bits of per cell from the 3rd byte of the extended ID */ +static int nand_get_bits_per_cell(u8 cellinfo) +{ + int bits; + + bits = cellinfo & NAND_CI_CELLTYPE_MSK; + bits >>= NAND_CI_CELLTYPE_SHIFT; + return bits + 1; +} + /* * Many new NAND share similar device ID codes, which represent the size of the * chip. The rest of the parameters must be decoded according to generic or @@ -3085,7 +3114,7 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, { int extid, id_len; /* The 3rd id byte holds MLC / multichip data */ - chip->cellinfo = id_data[2]; + chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]); /* The 4th id byte is the important one */ extid = id_data[3]; @@ -3101,8 +3130,7 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, * ID to decide what to do. */ if (id_len == 6 && id_data[0] == NAND_MFR_SAMSUNG && - (chip->cellinfo & NAND_CI_CELLTYPE_MSK) && - id_data[5] != 0x00) { + !nand_is_slc(chip) && id_data[5] != 0x00) { /* Calc pagesize */ mtd->writesize = 2048 << (extid & 0x03); extid >>= 2; @@ -3134,7 +3162,7 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, (((extid >> 1) & 0x04) | (extid & 0x03)); *busw = 0; } else if (id_len == 6 && id_data[0] == NAND_MFR_HYNIX && - (chip->cellinfo & NAND_CI_CELLTYPE_MSK)) { + !nand_is_slc(chip)) { unsigned int tmp; /* Calc pagesize */ @@ -3197,7 +3225,7 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, * - ID byte 5, bit[7]: 1 -> BENAND, 0 -> raw SLC */ if (id_len >= 6 && id_data[0] == NAND_MFR_TOSHIBA && - !(chip->cellinfo & NAND_CI_CELLTYPE_MSK) && + nand_is_slc(chip) && (id_data[5] & 0x7) == 0x6 /* 24nm */ && !(id_data[4] & 0x80) /* !BENAND */) { mtd->oobsize = 32 * mtd->writesize >> 9; @@ -3222,6 +3250,9 @@ static void nand_decode_id(struct mtd_info *mtd, struct nand_chip *chip, mtd->oobsize = mtd->writesize / 32; *busw = type->options & NAND_BUSWIDTH_16; + /* All legacy ID NAND are small-page, SLC */ + chip->bits_per_cell = 1; + /* * Check for Spansion/AMD ID + repeating 5th, 6th byte since * some Spansion chips have erasesize that conflicts with size @@ -3258,11 +3289,11 @@ static void nand_decode_bbm_options(struct mtd_info *mtd, * Micron devices with 2KiB pages and on SLC Samsung, Hynix, Toshiba, * AMD/Spansion, and Macronix. All others scan only the first page. */ - if ((chip->cellinfo & NAND_CI_CELLTYPE_MSK) && + if (!nand_is_slc(chip) && (maf_id == NAND_MFR_SAMSUNG || maf_id == NAND_MFR_HYNIX)) chip->bbt_options |= NAND_BBT_SCANLASTPAGE; - else if ((!(chip->cellinfo & NAND_CI_CELLTYPE_MSK) && + else if ((nand_is_slc(chip) && (maf_id == NAND_MFR_SAMSUNG || maf_id == NAND_MFR_HYNIX || maf_id == NAND_MFR_TOSHIBA || @@ -3286,7 +3317,7 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip, mtd->erasesize = type->erasesize; mtd->oobsize = type->oobsize; - chip->cellinfo = id_data[2]; + chip->bits_per_cell = nand_get_bits_per_cell(id_data[2]); chip->chipsize = (uint64_t)type->chipsize << 20; chip->options |= type->options; chip->ecc_strength_ds = NAND_ECC_STRENGTH(type); @@ -3441,11 +3472,13 @@ ident_done: if (mtd->writesize > 512 && chip->cmdfunc == nand_command) chip->cmdfunc = nand_command_lp; - pr_info("NAND device: Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s)," - " %dMiB, page size: %d, OOB size: %d\n", + pr_info("NAND device: Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, *dev_id, nand_manuf_ids[maf_idx].name, - chip->onfi_version ? chip->onfi_params.model : type->name, - (int)(chip->chipsize >> 20), mtd->writesize, mtd->oobsize); + chip->onfi_version ? chip->onfi_params.model : type->name); + + pr_info("NAND device: %dMiB, %s, page size: %d, OOB size: %d\n", + (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC", + mtd->writesize, mtd->oobsize); return type; } @@ -3525,6 +3558,7 @@ int nand_scan_tail(struct mtd_info *mtd) { int i; struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; /* New bad blocks should be marked in OOB, flash-based BBT, or both */ BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) && @@ -3541,19 +3575,19 @@ int nand_scan_tail(struct mtd_info *mtd) /* * If no default placement scheme is given, select an appropriate one. */ - if (!chip->ecc.layout && (chip->ecc.mode != NAND_ECC_SOFT_BCH)) { + if (!ecc->layout && (ecc->mode != NAND_ECC_SOFT_BCH)) { switch (mtd->oobsize) { case 8: - chip->ecc.layout = &nand_oob_8; + ecc->layout = &nand_oob_8; break; case 16: - chip->ecc.layout = &nand_oob_16; + ecc->layout = &nand_oob_16; break; case 64: - chip->ecc.layout = &nand_oob_64; + ecc->layout = &nand_oob_64; break; case 128: - chip->ecc.layout = &nand_oob_128; + ecc->layout = &nand_oob_128; break; default: pr_warn("No oob scheme defined for oobsize %d\n", @@ -3570,64 +3604,62 @@ int nand_scan_tail(struct mtd_info *mtd) * selected and we have 256 byte pagesize fallback to software ECC */ - switch (chip->ecc.mode) { + switch (ecc->mode) { case NAND_ECC_HW_OOB_FIRST: /* Similar to NAND_ECC_HW, but a separate read_page handle */ - if (!chip->ecc.calculate || !chip->ecc.correct || - !chip->ecc.hwctl) { + if (!ecc->calculate || !ecc->correct || !ecc->hwctl) { pr_warn("No ECC functions supplied; " "hardware ECC not possible\n"); BUG(); } - if (!chip->ecc.read_page) - chip->ecc.read_page = nand_read_page_hwecc_oob_first; + if (!ecc->read_page) + ecc->read_page = nand_read_page_hwecc_oob_first; case NAND_ECC_HW: /* Use standard hwecc read page function? */ - if (!chip->ecc.read_page) - chip->ecc.read_page = nand_read_page_hwecc; - if (!chip->ecc.write_page) - chip->ecc.write_page = nand_write_page_hwecc; - if (!chip->ecc.read_page_raw) - chip->ecc.read_page_raw = nand_read_page_raw; - if (!chip->ecc.write_page_raw) - chip->ecc.write_page_raw = nand_write_page_raw; - if (!chip->ecc.read_oob) - chip->ecc.read_oob = nand_read_oob_std; - if (!chip->ecc.write_oob) - chip->ecc.write_oob = nand_write_oob_std; - if (!chip->ecc.read_subpage) - chip->ecc.read_subpage = nand_read_subpage; - if (!chip->ecc.write_subpage) - chip->ecc.write_subpage = nand_write_subpage_hwecc; + if (!ecc->read_page) + ecc->read_page = nand_read_page_hwecc; + if (!ecc->write_page) + ecc->write_page = nand_write_page_hwecc; + if (!ecc->read_page_raw) + ecc->read_page_raw = nand_read_page_raw; + if (!ecc->write_page_raw) + ecc->write_page_raw = nand_write_page_raw; + if (!ecc->read_oob) + ecc->read_oob = nand_read_oob_std; + if (!ecc->write_oob) + ecc->write_oob = nand_write_oob_std; + if (!ecc->read_subpage) + ecc->read_subpage = nand_read_subpage; + if (!ecc->write_subpage) + ecc->write_subpage = nand_write_subpage_hwecc; case NAND_ECC_HW_SYNDROME: - if ((!chip->ecc.calculate || !chip->ecc.correct || - !chip->ecc.hwctl) && - (!chip->ecc.read_page || - chip->ecc.read_page == nand_read_page_hwecc || - !chip->ecc.write_page || - chip->ecc.write_page == nand_write_page_hwecc)) { + if ((!ecc->calculate || !ecc->correct || !ecc->hwctl) && + (!ecc->read_page || + ecc->read_page == nand_read_page_hwecc || + !ecc->write_page || + ecc->write_page == nand_write_page_hwecc)) { pr_warn("No ECC functions supplied; " "hardware ECC not possible\n"); BUG(); } /* Use standard syndrome read/write page function? */ - if (!chip->ecc.read_page) - chip->ecc.read_page = nand_read_page_syndrome; - if (!chip->ecc.write_page) - chip->ecc.write_page = nand_write_page_syndrome; - if (!chip->ecc.read_page_raw) - chip->ecc.read_page_raw = nand_read_page_raw_syndrome; - if (!chip->ecc.write_page_raw) - chip->ecc.write_page_raw = nand_write_page_raw_syndrome; - if (!chip->ecc.read_oob) - chip->ecc.read_oob = nand_read_oob_syndrome; - if (!chip->ecc.write_oob) - chip->ecc.write_oob = nand_write_oob_syndrome; - - if (mtd->writesize >= chip->ecc.size) { - if (!chip->ecc.strength) { + if (!ecc->read_page) + ecc->read_page = nand_read_page_syndrome; + if (!ecc->write_page) + ecc->write_page = nand_write_page_syndrome; + if (!ecc->read_page_raw) + ecc->read_page_raw = nand_read_page_raw_syndrome; + if (!ecc->write_page_raw) + ecc->write_page_raw = nand_write_page_raw_syndrome; + if (!ecc->read_oob) + ecc->read_oob = nand_read_oob_syndrome; + if (!ecc->write_oob) + ecc->write_oob = nand_write_oob_syndrome; + + if (mtd->writesize >= ecc->size) { + if (!ecc->strength) { pr_warn("Driver must set ecc.strength when using hardware ECC\n"); BUG(); } @@ -3635,23 +3667,23 @@ int nand_scan_tail(struct mtd_info *mtd) } pr_warn("%d byte HW ECC not possible on " "%d byte page size, fallback to SW ECC\n", - chip->ecc.size, mtd->writesize); - chip->ecc.mode = NAND_ECC_SOFT; + ecc->size, mtd->writesize); + ecc->mode = NAND_ECC_SOFT; case NAND_ECC_SOFT: - chip->ecc.calculate = nand_calculate_ecc; - chip->ecc.correct = nand_correct_data; - chip->ecc.read_page = nand_read_page_swecc; - chip->ecc.read_subpage = nand_read_subpage; - chip->ecc.write_page = nand_write_page_swecc; - chip->ecc.read_page_raw = nand_read_page_raw; - chip->ecc.write_page_raw = nand_write_page_raw; - chip->ecc.read_oob = nand_read_oob_std; - chip->ecc.write_oob = nand_write_oob_std; - if (!chip->ecc.size) - chip->ecc.size = 256; - chip->ecc.bytes = 3; - chip->ecc.strength = 1; + ecc->calculate = nand_calculate_ecc; + ecc->correct = nand_correct_data; + ecc->read_page = nand_read_page_swecc; + ecc->read_subpage = nand_read_subpage; + ecc->write_page = nand_write_page_swecc; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->write_oob = nand_write_oob_std; + if (!ecc->size) + ecc->size = 256; + ecc->bytes = 3; + ecc->strength = 1; break; case NAND_ECC_SOFT_BCH: @@ -3659,88 +3691,83 @@ int nand_scan_tail(struct mtd_info *mtd) pr_warn("CONFIG_MTD_ECC_BCH not enabled\n"); BUG(); } - chip->ecc.calculate = nand_bch_calculate_ecc; - chip->ecc.correct = nand_bch_correct_data; - chip->ecc.read_page = nand_read_page_swecc; - chip->ecc.read_subpage = nand_read_subpage; - chip->ecc.write_page = nand_write_page_swecc; - chip->ecc.read_page_raw = nand_read_page_raw; - chip->ecc.write_page_raw = nand_write_page_raw; - chip->ecc.read_oob = nand_read_oob_std; - chip->ecc.write_oob = nand_write_oob_std; + ecc->calculate = nand_bch_calculate_ecc; + ecc->correct = nand_bch_correct_data; + ecc->read_page = nand_read_page_swecc; + ecc->read_subpage = nand_read_subpage; + ecc->write_page = nand_write_page_swecc; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->write_oob = nand_write_oob_std; /* * Board driver should supply ecc.size and ecc.bytes values to * select how many bits are correctable; see nand_bch_init() * for details. Otherwise, default to 4 bits for large page * devices. */ - if (!chip->ecc.size && (mtd->oobsize >= 64)) { - chip->ecc.size = 512; - chip->ecc.bytes = 7; + if (!ecc->size && (mtd->oobsize >= 64)) { + ecc->size = 512; + ecc->bytes = 7; } - chip->ecc.priv = nand_bch_init(mtd, - chip->ecc.size, - chip->ecc.bytes, - &chip->ecc.layout); - if (!chip->ecc.priv) { + ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes, + &ecc->layout); + if (!ecc->priv) { pr_warn("BCH ECC initialization failed!\n"); BUG(); } - chip->ecc.strength = - chip->ecc.bytes * 8 / fls(8 * chip->ecc.size); + ecc->strength = ecc->bytes * 8 / fls(8 * ecc->size); break; case NAND_ECC_NONE: pr_warn("NAND_ECC_NONE selected by board driver. " "This is not recommended!\n"); - chip->ecc.read_page = nand_read_page_raw; - chip->ecc.write_page = nand_write_page_raw; - chip->ecc.read_oob = nand_read_oob_std; - chip->ecc.read_page_raw = nand_read_page_raw; - chip->ecc.write_page_raw = nand_write_page_raw; - chip->ecc.write_oob = nand_write_oob_std; - chip->ecc.size = mtd->writesize; - chip->ecc.bytes = 0; - chip->ecc.strength = 0; + ecc->read_page = nand_read_page_raw; + ecc->write_page = nand_write_page_raw; + ecc->read_oob = nand_read_oob_std; + ecc->read_page_raw = nand_read_page_raw; + ecc->write_page_raw = nand_write_page_raw; + ecc->write_oob = nand_write_oob_std; + ecc->size = mtd->writesize; + ecc->bytes = 0; + ecc->strength = 0; break; default: - pr_warn("Invalid NAND_ECC_MODE %d\n", chip->ecc.mode); + pr_warn("Invalid NAND_ECC_MODE %d\n", ecc->mode); BUG(); } /* For many systems, the standard OOB write also works for raw */ - if (!chip->ecc.read_oob_raw) - chip->ecc.read_oob_raw = chip->ecc.read_oob; - if (!chip->ecc.write_oob_raw) - chip->ecc.write_oob_raw = chip->ecc.write_oob; + if (!ecc->read_oob_raw) + ecc->read_oob_raw = ecc->read_oob; + if (!ecc->write_oob_raw) + ecc->write_oob_raw = ecc->write_oob; /* * The number of bytes available for a client to place data into * the out of band area. */ - chip->ecc.layout->oobavail = 0; - for (i = 0; chip->ecc.layout->oobfree[i].length - && i < ARRAY_SIZE(chip->ecc.layout->oobfree); i++) - chip->ecc.layout->oobavail += - chip->ecc.layout->oobfree[i].length; - mtd->oobavail = chip->ecc.layout->oobavail; + ecc->layout->oobavail = 0; + for (i = 0; ecc->layout->oobfree[i].length + && i < ARRAY_SIZE(ecc->layout->oobfree); i++) + ecc->layout->oobavail += ecc->layout->oobfree[i].length; + mtd->oobavail = ecc->layout->oobavail; /* * Set the number of read / write steps for one page depending on ECC * mode. */ - chip->ecc.steps = mtd->writesize / chip->ecc.size; - if (chip->ecc.steps * chip->ecc.size != mtd->writesize) { + ecc->steps = mtd->writesize / ecc->size; + if (ecc->steps * ecc->size != mtd->writesize) { pr_warn("Invalid ECC parameters\n"); BUG(); } - chip->ecc.total = chip->ecc.steps * chip->ecc.bytes; + ecc->total = ecc->steps * ecc->bytes; /* Allow subpage writes up to ecc.steps. Not possible for MLC flash */ - if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && - !(chip->cellinfo & NAND_CI_CELLTYPE_MSK)) { - switch (chip->ecc.steps) { + if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && nand_is_slc(chip)) { + switch (ecc->steps) { case 2: mtd->subpage_sft = 1; break; @@ -3760,11 +3787,11 @@ int nand_scan_tail(struct mtd_info *mtd) chip->pagebuf = -1; /* Large page NAND with SOFT_ECC should support subpage reads */ - if ((chip->ecc.mode == NAND_ECC_SOFT) && (chip->page_shift > 9)) + if ((ecc->mode == NAND_ECC_SOFT) && (chip->page_shift > 9)) chip->options |= NAND_SUBPAGE_READ; /* Fill in remaining MTD driver data */ - mtd->type = MTD_NANDFLASH; + mtd->type = nand_is_slc(chip) ? MTD_NANDFLASH : MTD_MLCNANDFLASH; mtd->flags = (chip->options & NAND_ROM) ? MTD_CAP_ROM : MTD_CAP_NANDFLASH; mtd->_erase = nand_erase; @@ -3785,9 +3812,9 @@ int nand_scan_tail(struct mtd_info *mtd) mtd->writebufsize = mtd->writesize; /* propagate ecc info to mtd_info */ - mtd->ecclayout = chip->ecc.layout; - mtd->ecc_strength = chip->ecc.strength; - mtd->ecc_step_size = chip->ecc.size; + mtd->ecclayout = ecc->layout; + mtd->ecc_strength = ecc->strength; + mtd->ecc_step_size = ecc->size; /* * Initialize bitflip_threshold to its default prior scan_bbt() call. * scan_bbt() might invoke mtd_read(), thus bitflip_threshold must be diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c index bc06196..c0615d1 100644 --- a/drivers/mtd/nand/nand_bbt.c +++ b/drivers/mtd/nand/nand_bbt.c @@ -412,25 +412,6 @@ static void read_abs_bbts(struct mtd_info *mtd, uint8_t *buf, } } -/* Scan a given block full */ -static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd, - loff_t offs, uint8_t *buf, size_t readlen, - int scanlen, int numpages) -{ - int ret, j; - - ret = scan_read_oob(mtd, buf, offs, readlen); - /* Ignore ECC errors when checking for BBM */ - if (ret && !mtd_is_bitflip_or_eccerr(ret)) - return ret; - - for (j = 0; j < numpages; j++, buf += scanlen) { - if (check_pattern(buf, scanlen, mtd->writesize, bd)) - return 1; - } - return 0; -} - /* Scan a given block partially */ static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd, loff_t offs, uint8_t *buf, int numpages) @@ -477,24 +458,17 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd, int chip) { struct nand_chip *this = mtd->priv; - int i, numblocks, numpages, scanlen; + int i, numblocks, numpages; int startblock; loff_t from; - size_t readlen; pr_info("Scanning device for bad blocks\n"); - if (bd->options & NAND_BBT_SCANALLPAGES) - numpages = 1 << (this->bbt_erase_shift - this->page_shift); - else if (bd->options & NAND_BBT_SCAN2NDPAGE) + if (bd->options & NAND_BBT_SCAN2NDPAGE) numpages = 2; else numpages = 1; - /* We need only read few bytes from the OOB area */ - scanlen = 0; - readlen = bd->len; - if (chip == -1) { numblocks = mtd->size >> this->bbt_erase_shift; startblock = 0; @@ -519,12 +493,7 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf, BUG_ON(bd->options & NAND_BBT_NO_OOB); - if (bd->options & NAND_BBT_SCANALLPAGES) - ret = scan_block_full(mtd, bd, from, buf, readlen, - scanlen, numpages); - else - ret = scan_block_fast(mtd, bd, from, buf, numpages); - + ret = scan_block_fast(mtd, bd, from, buf, numpages); if (ret < 0) return ret; @@ -1392,4 +1361,3 @@ int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs) } EXPORT_SYMBOL(nand_scan_bbt); -EXPORT_SYMBOL(nand_default_bbt); diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c index d1c7de9..42e8a77 100644 --- a/drivers/mtd/nand/nandsim.c +++ b/drivers/mtd/nand/nandsim.c @@ -2372,7 +2372,7 @@ static int __init ns_init_module(void) if ((retval = init_nandsim(nsmtd)) != 0) goto err_exit; - if ((retval = nand_default_bbt(nsmtd)) != 0) + if ((retval = chip->scan_bbt(nsmtd)) != 0) goto err_exit; if ((retval = parse_badblocks(nand, nsmtd)) != 0) diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 4ecf0e5..f777250 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -25,10 +25,8 @@ #include <linux/of.h> #include <linux/of_device.h> -#ifdef CONFIG_MTD_NAND_OMAP_BCH -#include <linux/bch.h> +#include <linux/mtd/nand_bch.h> #include <linux/platform_data/elm.h> -#endif #include <linux/platform_data/mtd-nand-omap2.h> @@ -141,6 +139,8 @@ #define BCH_ECC_SIZE0 0x0 /* ecc_size0 = 0, no oob protection */ #define BCH_ECC_SIZE1 0x20 /* ecc_size1 = 32 */ +#define BADBLOCK_MARKER_LENGTH 2 + #ifdef CONFIG_MTD_NAND_OMAP_BCH static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc, 0xac, 0x6b, 0xff, 0x99, 0x7b}; @@ -149,17 +149,6 @@ static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10}; /* oob info generated runtime depending on ecc algorithm and layout selected */ static struct nand_ecclayout omap_oobinfo; -/* Define some generic bad / good block scan pattern which are used - * while scanning a device for factory marked good / bad blocks - */ -static uint8_t scan_ff_pattern[] = { 0xff }; -static struct nand_bbt_descr bb_descrip_flashbased = { - .options = NAND_BBT_SCANALLPAGES, - .offs = 0, - .len = 1, - .pattern = scan_ff_pattern, -}; - struct omap_nand_info { struct nand_hw_control controller; @@ -182,14 +171,10 @@ struct omap_nand_info { u_char *buf; int buf_len; struct gpmc_nand_regs reg; - -#ifdef CONFIG_MTD_NAND_OMAP_BCH - struct bch_control *bch; - struct nand_ecclayout ecclayout; + /* fields specific for BCHx_HW ECC scheme */ bool is_elm_used; struct device *elm_dev; struct device_node *of_node; -#endif }; /** @@ -1058,8 +1043,7 @@ static int omap_dev_ready(struct mtd_info *mtd) } } -#ifdef CONFIG_MTD_NAND_OMAP_BCH - +#if defined(CONFIG_MTD_NAND_ECC_BCH) || defined(CONFIG_MTD_NAND_OMAP_BCH) /** * omap3_enable_hwecc_bch - Program OMAP3 GPMC to perform BCH ECC correction * @mtd: MTD device structure @@ -1140,7 +1124,9 @@ static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode) /* Clear ecc and enable bits */ writel(ECCCLEAR | ECC1, info->reg.gpmc_ecc_control); } +#endif +#ifdef CONFIG_MTD_NAND_ECC_BCH /** * omap3_calculate_ecc_bch4 - Generate 7 bytes of ECC bytes * @mtd: MTD device structure @@ -1225,7 +1211,9 @@ static int omap3_calculate_ecc_bch8(struct mtd_info *mtd, const u_char *dat, return 0; } +#endif /* CONFIG_MTD_NAND_ECC_BCH */ +#ifdef CONFIG_MTD_NAND_OMAP_BCH /** * omap3_calculate_ecc_bch - Generate bytes of ECC bytes * @mtd: MTD device structure @@ -1519,38 +1507,6 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data, } /** - * omap3_correct_data_bch - Decode received data and correct errors - * @mtd: MTD device structure - * @data: page data - * @read_ecc: ecc read from nand flash - * @calc_ecc: ecc read from HW ECC registers - */ -static int omap3_correct_data_bch(struct mtd_info *mtd, u_char *data, - u_char *read_ecc, u_char *calc_ecc) -{ - int i, count; - /* cannot correct more than 8 errors */ - unsigned int errloc[8]; - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - - count = decode_bch(info->bch, NULL, 512, read_ecc, calc_ecc, NULL, - errloc); - if (count > 0) { - /* correct errors */ - for (i = 0; i < count; i++) { - /* correct data only, not ecc bytes */ - if (errloc[i] < 8*512) - data[errloc[i]/8] ^= 1 << (errloc[i] & 7); - pr_debug("corrected bitflip %u\n", errloc[i]); - } - } else if (count < 0) { - pr_err("ecc unrecoverable error\n"); - } - return count; -} - -/** * omap_write_page_bch - BCH ecc based write page function for entire page * @mtd: mtd info structure * @chip: nand chip info structure @@ -1637,197 +1593,46 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, } /** - * omap3_free_bch - Release BCH ecc resources - * @mtd: MTD device structure - */ -static void omap3_free_bch(struct mtd_info *mtd) -{ - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - if (info->bch) { - free_bch(info->bch); - info->bch = NULL; - } -} - -/** - * omap3_init_bch - Initialize BCH ECC - * @mtd: MTD device structure - * @ecc_opt: OMAP ECC mode (OMAP_ECC_BCH4_CODE_HW or OMAP_ECC_BCH8_CODE_HW) - */ -static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) -{ - int max_errors; - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); -#ifdef CONFIG_MTD_NAND_OMAP_BCH8 - const int hw_errors = BCH8_MAX_ERROR; -#else - const int hw_errors = BCH4_MAX_ERROR; -#endif - enum bch_ecc bch_type; - const __be32 *parp; - int lenp; - struct device_node *elm_node; - - info->bch = NULL; - - max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ? - BCH8_MAX_ERROR : BCH4_MAX_ERROR; - if (max_errors != hw_errors) { - pr_err("cannot configure %d-bit BCH ecc, only %d-bit supported", - max_errors, hw_errors); - goto fail; - } - - info->nand.ecc.size = 512; - info->nand.ecc.hwctl = omap3_enable_hwecc_bch; - info->nand.ecc.mode = NAND_ECC_HW; - info->nand.ecc.strength = max_errors; - - if (hw_errors == BCH8_MAX_ERROR) - bch_type = BCH8_ECC; - else - bch_type = BCH4_ECC; - - /* Detect availability of ELM module */ - parp = of_get_property(info->of_node, "elm_id", &lenp); - if ((parp == NULL) && (lenp != (sizeof(void *) * 2))) { - pr_err("Missing elm_id property, fall back to Software BCH\n"); - info->is_elm_used = false; - } else { - struct platform_device *pdev; - - elm_node = of_find_node_by_phandle(be32_to_cpup(parp)); - pdev = of_find_device_by_node(elm_node); - info->elm_dev = &pdev->dev; - - if (elm_config(info->elm_dev, bch_type) == 0) - info->is_elm_used = true; - } - - if (info->is_elm_used && (mtd->writesize <= 4096)) { - - if (hw_errors == BCH8_MAX_ERROR) - info->nand.ecc.bytes = BCH8_SIZE; - else - info->nand.ecc.bytes = BCH4_SIZE; - - info->nand.ecc.correct = omap_elm_correct_data; - info->nand.ecc.calculate = omap3_calculate_ecc_bch; - info->nand.ecc.read_page = omap_read_page_bch; - info->nand.ecc.write_page = omap_write_page_bch; - } else { - /* - * software bch library is only used to detect and - * locate errors - */ - info->bch = init_bch(13, max_errors, - 0x201b /* hw polynomial */); - if (!info->bch) - goto fail; - - info->nand.ecc.correct = omap3_correct_data_bch; - - /* - * The number of corrected errors in an ecc block that will - * trigger block scrubbing defaults to the ecc strength (4 or 8) - * Set mtd->bitflip_threshold here to define a custom threshold. - */ - - if (max_errors == 8) { - info->nand.ecc.bytes = 13; - info->nand.ecc.calculate = omap3_calculate_ecc_bch8; - } else { - info->nand.ecc.bytes = 7; - info->nand.ecc.calculate = omap3_calculate_ecc_bch4; - } - } - - pr_info("enabling NAND BCH ecc with %d-bit correction\n", max_errors); - return 0; -fail: - omap3_free_bch(mtd); - return -1; -} - -/** - * omap3_init_bch_tail - Build an oob layout for BCH ECC correction. - * @mtd: MTD device structure + * is_elm_present - checks for presence of ELM module by scanning DT nodes + * @omap_nand_info: NAND device structure containing platform data + * @bch_type: 0x0=BCH4, 0x1=BCH8, 0x2=BCH16 */ -static int omap3_init_bch_tail(struct mtd_info *mtd) +static int is_elm_present(struct omap_nand_info *info, + struct device_node *elm_node, enum bch_ecc bch_type) { - int i, steps, offset; - struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, - mtd); - struct nand_ecclayout *layout = &info->ecclayout; - - /* build oob layout */ - steps = mtd->writesize/info->nand.ecc.size; - layout->eccbytes = steps*info->nand.ecc.bytes; - - /* do not bother creating special oob layouts for small page devices */ - if (mtd->oobsize < 64) { - pr_err("BCH ecc is not supported on small page devices\n"); - goto fail; + struct platform_device *pdev; + info->is_elm_used = false; + /* check whether elm-id is passed via DT */ + if (!elm_node) { + pr_err("nand: error: ELM DT node not found\n"); + return -ENODEV; } - - /* reserve 2 bytes for bad block marker */ - if (layout->eccbytes+2 > mtd->oobsize) { - pr_err("no oob layout available for oobsize %d eccbytes %u\n", - mtd->oobsize, layout->eccbytes); - goto fail; + pdev = of_find_device_by_node(elm_node); + /* check whether ELM device is registered */ + if (!pdev) { + pr_err("nand: error: ELM device not found\n"); + return -ENODEV; } - - /* ECC layout compatible with RBL for BCH8 */ - if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE)) - offset = 2; - else - offset = mtd->oobsize - layout->eccbytes; - - /* put ecc bytes at oob tail */ - for (i = 0; i < layout->eccbytes; i++) - layout->eccpos[i] = offset + i; - - if (info->is_elm_used && (info->nand.ecc.bytes == BCH8_SIZE)) - layout->oobfree[0].offset = 2 + layout->eccbytes * steps; - else - layout->oobfree[0].offset = 2; - - layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes; - info->nand.ecc.layout = layout; - - if (!(info->nand.options & NAND_BUSWIDTH_16)) - info->nand.badblock_pattern = &bb_descrip_flashbased; + /* ELM module available, now configure it */ + info->elm_dev = &pdev->dev; + if (elm_config(info->elm_dev, bch_type)) + return -ENODEV; + info->is_elm_used = true; return 0; -fail: - omap3_free_bch(mtd); - return -1; -} - -#else -static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) -{ - pr_err("CONFIG_MTD_NAND_OMAP_BCH is not enabled\n"); - return -1; -} -static int omap3_init_bch_tail(struct mtd_info *mtd) -{ - return -1; -} -static void omap3_free_bch(struct mtd_info *mtd) -{ } -#endif /* CONFIG_MTD_NAND_OMAP_BCH */ +#endif /* CONFIG_MTD_NAND_ECC_BCH */ static int omap_nand_probe(struct platform_device *pdev) { struct omap_nand_info *info; struct omap_nand_platform_data *pdata; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + struct nand_ecclayout *ecclayout; int err; - int i, offset; - dma_cap_mask_t mask; - unsigned sig; + int i; + dma_cap_mask_t mask; + unsigned sig; struct resource *res; struct mtd_part_parser_data ppdata = {}; @@ -1837,7 +1642,8 @@ static int omap_nand_probe(struct platform_device *pdev) return -ENODEV; } - info = kzalloc(sizeof(struct omap_nand_info), GFP_KERNEL); + info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info), + GFP_KERNEL); if (!info) return -ENOMEM; @@ -1846,47 +1652,45 @@ static int omap_nand_probe(struct platform_device *pdev) spin_lock_init(&info->controller.lock); init_waitqueue_head(&info->controller.wq); - info->pdev = pdev; - + info->pdev = pdev; info->gpmc_cs = pdata->cs; info->reg = pdata->reg; - - info->mtd.priv = &info->nand; - info->mtd.name = dev_name(&pdev->dev); - info->mtd.owner = THIS_MODULE; - - info->nand.options = pdata->devsize; - info->nand.options |= NAND_SKIP_BBTSCAN; -#ifdef CONFIG_MTD_NAND_OMAP_BCH info->of_node = pdata->of_node; -#endif + mtd = &info->mtd; + mtd->priv = &info->nand; + mtd->name = dev_name(&pdev->dev); + mtd->owner = THIS_MODULE; + nand_chip = &info->nand; + nand_chip->ecc.priv = NULL; + nand_chip->options |= NAND_SKIP_BBTSCAN; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (res == NULL) { err = -EINVAL; dev_err(&pdev->dev, "error getting memory resource\n"); - goto out_free_info; + goto return_error; } info->phys_base = res->start; info->mem_size = resource_size(res); - if (!request_mem_region(info->phys_base, info->mem_size, - pdev->dev.driver->name)) { + if (!devm_request_mem_region(&pdev->dev, info->phys_base, + info->mem_size, pdev->dev.driver->name)) { err = -EBUSY; - goto out_free_info; + goto return_error; } - info->nand.IO_ADDR_R = ioremap(info->phys_base, info->mem_size); - if (!info->nand.IO_ADDR_R) { + nand_chip->IO_ADDR_R = devm_ioremap(&pdev->dev, info->phys_base, + info->mem_size); + if (!nand_chip->IO_ADDR_R) { err = -ENOMEM; - goto out_release_mem_region; + goto return_error; } - info->nand.controller = &info->controller; + nand_chip->controller = &info->controller; - info->nand.IO_ADDR_W = info->nand.IO_ADDR_R; - info->nand.cmd_ctrl = omap_hwcontrol; + nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R; + nand_chip->cmd_ctrl = omap_hwcontrol; /* * If RDY/BSY line is connected to OMAP then use the omap ready @@ -1896,26 +1700,42 @@ static int omap_nand_probe(struct platform_device *pdev) * device and read status register until you get a failure or success */ if (pdata->dev_ready) { - info->nand.dev_ready = omap_dev_ready; - info->nand.chip_delay = 0; + nand_chip->dev_ready = omap_dev_ready; + nand_chip->chip_delay = 0; } else { - info->nand.waitfunc = omap_wait; - info->nand.chip_delay = 50; + nand_chip->waitfunc = omap_wait; + nand_chip->chip_delay = 50; } + /* scan NAND device connected to chip controller */ + nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16; + if (nand_scan_ident(mtd, 1, NULL)) { + pr_err("nand device scan failed, may be bus-width mismatch\n"); + err = -ENXIO; + goto return_error; + } + + /* check for small page devices */ + if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) { + pr_err("small page devices are not supported\n"); + err = -EINVAL; + goto return_error; + } + + /* re-populate low-level callbacks based on xfer modes */ switch (pdata->xfer_type) { case NAND_OMAP_PREFETCH_POLLED: - info->nand.read_buf = omap_read_buf_pref; - info->nand.write_buf = omap_write_buf_pref; + nand_chip->read_buf = omap_read_buf_pref; + nand_chip->write_buf = omap_write_buf_pref; break; case NAND_OMAP_POLLED: - if (info->nand.options & NAND_BUSWIDTH_16) { - info->nand.read_buf = omap_read_buf16; - info->nand.write_buf = omap_write_buf16; + if (nand_chip->options & NAND_BUSWIDTH_16) { + nand_chip->read_buf = omap_read_buf16; + nand_chip->write_buf = omap_write_buf16; } else { - info->nand.read_buf = omap_read_buf8; - info->nand.write_buf = omap_write_buf8; + nand_chip->read_buf = omap_read_buf8; + nand_chip->write_buf = omap_write_buf8; } break; @@ -1927,7 +1747,7 @@ static int omap_nand_probe(struct platform_device *pdev) if (!info->dma) { dev_err(&pdev->dev, "DMA engine request failed\n"); err = -ENXIO; - goto out_release_mem_region; + goto return_error; } else { struct dma_slave_config cfg; @@ -1942,10 +1762,10 @@ static int omap_nand_probe(struct platform_device *pdev) if (err) { dev_err(&pdev->dev, "DMA engine slave config failed: %d\n", err); - goto out_release_mem_region; + goto return_error; } - info->nand.read_buf = omap_read_buf_dma_pref; - info->nand.write_buf = omap_write_buf_dma_pref; + nand_chip->read_buf = omap_read_buf_dma_pref; + nand_chip->write_buf = omap_write_buf_dma_pref; } break; @@ -1954,34 +1774,36 @@ static int omap_nand_probe(struct platform_device *pdev) if (info->gpmc_irq_fifo <= 0) { dev_err(&pdev->dev, "error getting fifo irq\n"); err = -ENODEV; - goto out_release_mem_region; + goto return_error; } - err = request_irq(info->gpmc_irq_fifo, omap_nand_irq, - IRQF_SHARED, "gpmc-nand-fifo", info); + err = devm_request_irq(&pdev->dev, info->gpmc_irq_fifo, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-fifo", info); if (err) { dev_err(&pdev->dev, "requesting irq(%d) error:%d", info->gpmc_irq_fifo, err); info->gpmc_irq_fifo = 0; - goto out_release_mem_region; + goto return_error; } info->gpmc_irq_count = platform_get_irq(pdev, 1); if (info->gpmc_irq_count <= 0) { dev_err(&pdev->dev, "error getting count irq\n"); err = -ENODEV; - goto out_release_mem_region; + goto return_error; } - err = request_irq(info->gpmc_irq_count, omap_nand_irq, - IRQF_SHARED, "gpmc-nand-count", info); + err = devm_request_irq(&pdev->dev, info->gpmc_irq_count, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-count", info); if (err) { dev_err(&pdev->dev, "requesting irq(%d) error:%d", info->gpmc_irq_count, err); info->gpmc_irq_count = 0; - goto out_release_mem_region; + goto return_error; } - info->nand.read_buf = omap_read_buf_irq_pref; - info->nand.write_buf = omap_write_buf_irq_pref; + nand_chip->read_buf = omap_read_buf_irq_pref; + nand_chip->write_buf = omap_write_buf_irq_pref; break; @@ -1989,117 +1811,223 @@ static int omap_nand_probe(struct platform_device *pdev) dev_err(&pdev->dev, "xfer_type(%d) not supported!\n", pdata->xfer_type); err = -EINVAL; - goto out_release_mem_region; + goto return_error; } - /* select the ecc type */ - if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_DEFAULT) - info->nand.ecc.mode = NAND_ECC_SOFT; - else if ((pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE)) { - info->nand.ecc.bytes = 3; - info->nand.ecc.size = 512; - info->nand.ecc.strength = 1; - info->nand.ecc.calculate = omap_calculate_ecc; - info->nand.ecc.hwctl = omap_enable_hwecc; - info->nand.ecc.correct = omap_correct_data; - info->nand.ecc.mode = NAND_ECC_HW; - } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { - err = omap3_init_bch(&info->mtd, pdata->ecc_opt); - if (err) { + /* populate MTD interface based on ECC scheme */ + nand_chip->ecc.layout = &omap_oobinfo; + ecclayout = &omap_oobinfo; + switch (pdata->ecc_opt) { + case OMAP_ECC_HAM1_CODE_HW: + pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.bytes = 3; + nand_chip->ecc.size = 512; + nand_chip->ecc.strength = 1; + nand_chip->ecc.calculate = omap_calculate_ecc; + nand_chip->ecc.hwctl = omap_enable_hwecc; + nand_chip->ecc.correct = omap_correct_data; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + if (nand_chip->options & NAND_BUSWIDTH_16) + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + else + ecclayout->eccpos[0] = 1; + ecclayout->oobfree->offset = ecclayout->eccpos[0] + + ecclayout->eccbytes; + break; + + case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: +#ifdef CONFIG_MTD_NAND_ECC_BCH + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 7; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap3_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap3_calculate_ecc_bch4; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree->offset = ecclayout->eccpos[0] + + ecclayout->eccbytes; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &nand_chip->ecc.layout); + if (!nand_chip->ecc.priv) { + pr_err("nand: error: unable to use s/w BCH library\n"); err = -EINVAL; - goto out_release_mem_region; } - } + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif - /* DIP switches on some boards change between 8 and 16 bit - * bus widths for flash. Try the other width if the first try fails. - */ - if (nand_scan_ident(&info->mtd, 1, NULL)) { - info->nand.options ^= NAND_BUSWIDTH_16; - if (nand_scan_ident(&info->mtd, 1, NULL)) { - err = -ENXIO; - goto out_release_mem_region; + case OMAP_ECC_BCH4_CODE_HW: +#ifdef CONFIG_MTD_NAND_OMAP_BCH + pr_info("nand: using OMAP_ECC_BCH4_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 7 + 1; + nand_chip->ecc.strength = 4; + nand_chip->ecc.hwctl = omap3_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap3_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree->offset = ecclayout->eccpos[0] + + ecclayout->eccbytes; + /* This ECC scheme requires ELM H/W block */ + if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) { + pr_err("nand: error: could not initialize ELM\n"); + err = -ENODEV; + goto return_error; } - } - - /* rom code layout */ - if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE) { + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif - if (info->nand.options & NAND_BUSWIDTH_16) - offset = 2; - else { - offset = 1; - info->nand.badblock_pattern = &bb_descrip_flashbased; - } - omap_oobinfo.eccbytes = 3 * (info->mtd.oobsize/16); - for (i = 0; i < omap_oobinfo.eccbytes; i++) - omap_oobinfo.eccpos[i] = i+offset; - - omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes; - omap_oobinfo.oobfree->length = info->mtd.oobsize - - (offset + omap_oobinfo.eccbytes); - - info->nand.ecc.layout = &omap_oobinfo; - } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || - (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { - /* build OOB layout for BCH ECC correction */ - err = omap3_init_bch_tail(&info->mtd); - if (err) { + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: +#ifdef CONFIG_MTD_NAND_ECC_BCH + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + nand_chip->ecc.bytes = 13; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap3_enable_hwecc_bch; + nand_chip->ecc.correct = nand_bch_correct_data; + nand_chip->ecc.calculate = omap3_calculate_ecc_bch8; + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree->offset = ecclayout->eccpos[0] + + ecclayout->eccbytes; + /* software bch library is used for locating errors */ + nand_chip->ecc.priv = nand_bch_init(mtd, + nand_chip->ecc.size, + nand_chip->ecc.bytes, + &nand_chip->ecc.layout); + if (!nand_chip->ecc.priv) { + pr_err("nand: error: unable to use s/w BCH library\n"); err = -EINVAL; - goto out_release_mem_region; + goto return_error; + } + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif + + case OMAP_ECC_BCH8_CODE_HW: +#ifdef CONFIG_MTD_NAND_OMAP_BCH + pr_info("nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme\n"); + nand_chip->ecc.mode = NAND_ECC_HW; + nand_chip->ecc.size = 512; + /* 14th bit is kept reserved for ROM-code compatibility */ + nand_chip->ecc.bytes = 13 + 1; + nand_chip->ecc.strength = 8; + nand_chip->ecc.hwctl = omap3_enable_hwecc_bch; + nand_chip->ecc.correct = omap_elm_correct_data; + nand_chip->ecc.calculate = omap3_calculate_ecc_bch; + nand_chip->ecc.read_page = omap_read_page_bch; + nand_chip->ecc.write_page = omap_write_page_bch; + /* This ECC scheme requires ELM H/W block */ + err = is_elm_present(info, pdata->elm_of_node, BCH8_ECC); + if (err < 0) { + pr_err("nand: error: could not initialize ELM\n"); + goto return_error; } + /* define ECC layout */ + ecclayout->eccbytes = nand_chip->ecc.bytes * + (mtd->writesize / + nand_chip->ecc.size); + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree->offset = ecclayout->eccpos[0] + + ecclayout->eccbytes; + break; +#else + pr_err("nand: error: CONFIG_MTD_NAND_OMAP_BCH not enabled\n"); + err = -EINVAL; + goto return_error; +#endif + + default: + pr_err("nand: error: invalid or unsupported ECC scheme\n"); + err = -EINVAL; + goto return_error; + } + + /* populate remaining ECC layout data */ + ecclayout->oobfree->length = mtd->oobsize - (BADBLOCK_MARKER_LENGTH + + ecclayout->eccbytes); + for (i = 1; i < ecclayout->eccbytes; i++) + ecclayout->eccpos[i] = ecclayout->eccpos[0] + i; + /* check if NAND device's OOB is enough to store ECC signatures */ + if (mtd->oobsize < (ecclayout->eccbytes + BADBLOCK_MARKER_LENGTH)) { + pr_err("not enough OOB bytes required = %d, available=%d\n", + ecclayout->eccbytes, mtd->oobsize); + err = -EINVAL; + goto return_error; } /* second phase scan */ - if (nand_scan_tail(&info->mtd)) { + if (nand_scan_tail(mtd)) { err = -ENXIO; - goto out_release_mem_region; + goto return_error; } ppdata.of_node = pdata->of_node; - mtd_device_parse_register(&info->mtd, NULL, &ppdata, pdata->parts, + mtd_device_parse_register(mtd, NULL, &ppdata, pdata->parts, pdata->nr_parts); - platform_set_drvdata(pdev, &info->mtd); + platform_set_drvdata(pdev, mtd); return 0; -out_release_mem_region: +return_error: if (info->dma) dma_release_channel(info->dma); - if (info->gpmc_irq_count > 0) - free_irq(info->gpmc_irq_count, info); - if (info->gpmc_irq_fifo > 0) - free_irq(info->gpmc_irq_fifo, info); - release_mem_region(info->phys_base, info->mem_size); -out_free_info: - kfree(info); - + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } return err; } static int omap_nand_remove(struct platform_device *pdev) { struct mtd_info *mtd = platform_get_drvdata(pdev); + struct nand_chip *nand_chip = mtd->priv; struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); - omap3_free_bch(&info->mtd); - + if (nand_chip->ecc.priv) { + nand_bch_free(nand_chip->ecc.priv); + nand_chip->ecc.priv = NULL; + } if (info->dma) dma_release_channel(info->dma); - - if (info->gpmc_irq_count > 0) - free_irq(info->gpmc_irq_count, info); - if (info->gpmc_irq_fifo > 0) - free_irq(info->gpmc_irq_fifo, info); - - /* Release NAND device, its internal structures and partitions */ - nand_release(&info->mtd); - iounmap(info->nand.IO_ADDR_R); - release_mem_region(info->phys_base, info->mem_size); - kfree(info); + nand_release(mtd); return 0; } diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index c28d4e2..4cabdc9 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -39,6 +39,13 @@ #define NAND_STOP_DELAY (2 * HZ/50) #define PAGE_CHUNK_SIZE (2048) +/* + * Define a buffer size for the initial command that detects the flash device: + * STATUS, READID and PARAM. The largest of these is the PARAM command, + * needing 256 bytes. + */ +#define INIT_BUFFER_SIZE 256 + /* registers and bit definitions */ #define NDCR (0x00) /* Control register */ #define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */ @@ -164,6 +171,7 @@ struct pxa3xx_nand_info { unsigned int buf_start; unsigned int buf_count; + unsigned int buf_size; /* DMA information */ int drcmr_dat; @@ -540,7 +548,6 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command, info->oob_size = 0; info->use_ecc = 0; info->use_spare = 1; - info->use_dma = (use_dma) ? 1 : 0; info->is_ready = 0; info->retcode = ERR_NONE; if (info->cs != 0) @@ -912,26 +919,20 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) return 0; } -/* the maximum possible buffer size for large page with OOB data - * is: 2048 + 64 = 2112 bytes, allocate a page here for both the - * data buffer and the DMA descriptor - */ -#define MAX_BUFF_SIZE PAGE_SIZE - #ifdef ARCH_HAS_DMA static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) { struct platform_device *pdev = info->pdev; - int data_desc_offset = MAX_BUFF_SIZE - sizeof(struct pxa_dma_desc); + int data_desc_offset = info->buf_size - sizeof(struct pxa_dma_desc); if (use_dma == 0) { - info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL); + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); if (info->data_buff == NULL) return -ENOMEM; return 0; } - info->data_buff = dma_alloc_coherent(&pdev->dev, MAX_BUFF_SIZE, + info->data_buff = dma_alloc_coherent(&pdev->dev, info->buf_size, &info->data_buff_phys, GFP_KERNEL); if (info->data_buff == NULL) { dev_err(&pdev->dev, "failed to allocate dma buffer\n"); @@ -945,11 +946,16 @@ static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) pxa3xx_nand_data_dma_irq, info); if (info->data_dma_ch < 0) { dev_err(&pdev->dev, "failed to request data dma\n"); - dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE, + dma_free_coherent(&pdev->dev, info->buf_size, info->data_buff, info->data_buff_phys); return info->data_dma_ch; } + /* + * Now that DMA buffers are allocated we turn on + * DMA proper for I/O operations. + */ + info->use_dma = 1; return 0; } @@ -958,7 +964,7 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) struct platform_device *pdev = info->pdev; if (use_dma) { pxa_free_dma(info->data_dma_ch); - dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE, + dma_free_coherent(&pdev->dev, info->buf_size, info->data_buff, info->data_buff_phys); } else { kfree(info->data_buff); @@ -967,7 +973,7 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) #else static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) { - info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL); + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); if (info->data_buff == NULL) return -ENOMEM; return 0; @@ -1081,7 +1087,16 @@ KEEP_CONFIG: else host->col_addr_cycles = 1; + /* release the initial buffer */ + kfree(info->data_buff); + + /* allocate the real data + oob buffer */ + info->buf_size = mtd->writesize + mtd->oobsize; + ret = pxa3xx_nand_init_buff(info); + if (ret) + return ret; info->oob_buff = info->data_buff + mtd->writesize; + if ((mtd->size >> chip->page_shift) > 65536) host->row_addr_cycles = 3; else @@ -1187,15 +1202,18 @@ static int alloc_nand_resource(struct platform_device *pdev) } info->mmio_phys = r->start; - ret = pxa3xx_nand_init_buff(info); - if (ret) + /* Allocate a buffer to allow flash detection */ + info->buf_size = INIT_BUFFER_SIZE; + info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); + if (info->data_buff == NULL) { + ret = -ENOMEM; goto fail_disable_clk; + } /* initialize all interrupts to be disabled */ disable_int(info, NDSR_MASK); - ret = request_irq(irq, pxa3xx_nand_irq, IRQF_DISABLED, - pdev->name, info); + ret = request_irq(irq, pxa3xx_nand_irq, 0, pdev->name, info); if (ret < 0) { dev_err(&pdev->dev, "failed to request IRQ\n"); goto fail_free_buf; @@ -1207,7 +1225,7 @@ static int alloc_nand_resource(struct platform_device *pdev) fail_free_buf: free_irq(irq, info); - pxa3xx_nand_free_buff(info); + kfree(info->data_buff); fail_disable_clk: clk_disable_unprepare(info->clk); return ret; @@ -1412,7 +1430,7 @@ static int pxa3xx_nand_resume(struct platform_device *pdev) static struct platform_driver pxa3xx_nand_driver = { .driver = { .name = "pxa3xx-nand", - .of_match_table = of_match_ptr(pxa3xx_nand_dt_ids), + .of_match_table = pxa3xx_nand_dt_ids, }, .probe = pxa3xx_nand_probe, .remove = pxa3xx_nand_remove, diff --git a/drivers/mtd/nand/socrates_nand.c b/drivers/mtd/nand/socrates_nand.c index 49bd9155..fe8058a 100644 --- a/drivers/mtd/nand/socrates_nand.c +++ b/drivers/mtd/nand/socrates_nand.c @@ -150,17 +150,13 @@ static int socrates_nand_probe(struct platform_device *ofdev) struct mtd_part_parser_data ppdata; /* Allocate memory for the device structure (and zero it) */ - host = kzalloc(sizeof(struct socrates_nand_host), GFP_KERNEL); - if (!host) { - printk(KERN_ERR - "socrates_nand: failed to allocate device structure.\n"); + host = devm_kzalloc(&ofdev->dev, sizeof(*host), GFP_KERNEL); + if (!host) return -ENOMEM; - } host->io_base = of_iomap(ofdev->dev.of_node, 0); if (host->io_base == NULL) { - printk(KERN_ERR "socrates_nand: ioremap failed\n"); - kfree(host); + dev_err(&ofdev->dev, "ioremap failed\n"); return -EIO; } @@ -212,9 +208,7 @@ static int socrates_nand_probe(struct platform_device *ofdev) nand_release(mtd); out: - dev_set_drvdata(&ofdev->dev, NULL); iounmap(host->io_base); - kfree(host); return res; } @@ -228,9 +222,7 @@ static int socrates_nand_remove(struct platform_device *ofdev) nand_release(mtd); - dev_set_drvdata(&ofdev->dev, NULL); iounmap(host->io_base); - kfree(host); return 0; } diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c index 396530d..a3747c9 100644 --- a/drivers/mtd/nand/tmio_nand.c +++ b/drivers/mtd/nand/tmio_nand.c @@ -428,8 +428,7 @@ static int tmio_probe(struct platform_device *dev) /* 15 us command delay time */ nand_chip->chip_delay = 15; - retval = request_irq(irq, &tmio_irq, - IRQF_DISABLED, dev_name(&dev->dev), tmio); + retval = request_irq(irq, &tmio_irq, 0, dev_name(&dev->dev), tmio); if (retval) { dev_err(&dev->dev, "request_irq error %d\n", retval); goto err_irq; diff --git a/drivers/mtd/nftlcore.c b/drivers/mtd/nftlcore.c index c5f4ebf..46f27de 100644 --- a/drivers/mtd/nftlcore.c +++ b/drivers/mtd/nftlcore.c @@ -50,7 +50,7 @@ static void nftl_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd) struct NFTLrecord *nftl; unsigned long temp; - if (mtd->type != MTD_NANDFLASH || mtd->size > UINT_MAX) + if (!mtd_type_is_nand(mtd) || mtd->size > UINT_MAX) return; /* OK, this is moderately ugly. But probably safe. Alternatives? */ if (memcmp(mtd->name, "DiskOnChip", 10)) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 558071b..2362909 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -573,28 +573,6 @@ static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, static struct platform_driver omap2_onenand_driver; -static int __adjust_timing(struct device *dev, void *data) -{ - int ret = 0; - struct omap2_onenand *c; - - c = dev_get_drvdata(dev); - - BUG_ON(c->setup == NULL); - - /* DMA is not in use so this is all that is needed */ - /* Revisit for OMAP3! */ - ret = c->setup(c->onenand.base, &c->freq); - - return ret; -} - -int omap2_onenand_rephase(void) -{ - return driver_for_each_device(&omap2_onenand_driver.driver, NULL, - NULL, __adjust_timing); -} - static void omap2_onenand_shutdown(struct platform_device *pdev) { struct omap2_onenand *c = dev_get_drvdata(&pdev->dev); diff --git a/drivers/mtd/onenand/onenand_base.c b/drivers/mtd/onenand/onenand_base.c index b3f41f2..1de33b5 100644 --- a/drivers/mtd/onenand/onenand_base.c +++ b/drivers/mtd/onenand/onenand_base.c @@ -2556,10 +2556,6 @@ static int onenand_block_isbad(struct mtd_info *mtd, loff_t ofs) { int ret; - /* Check for invalid offset */ - if (ofs > mtd->size) - return -EINVAL; - onenand_get_device(mtd, FL_READING); ret = onenand_block_isbad_nolock(mtd, ofs, 0); onenand_release_device(mtd); @@ -3529,7 +3525,7 @@ static int flexonenand_get_boundary(struct mtd_info *mtd) { struct onenand_chip *this = mtd->priv; unsigned die, bdry; - int ret, syscfg, locked; + int syscfg, locked; /* Disable ECC */ syscfg = this->read_word(this->base + ONENAND_REG_SYS_CFG1); @@ -3540,7 +3536,7 @@ static int flexonenand_get_boundary(struct mtd_info *mtd) this->wait(mtd, FL_SYNCING); this->command(mtd, FLEXONENAND_CMD_READ_PI, die, 0); - ret = this->wait(mtd, FL_READING); + this->wait(mtd, FL_READING); bdry = this->read_word(this->base + ONENAND_DATARAM); if ((bdry >> FLEXONENAND_PI_UNLOCK_SHIFT) == 3) @@ -3550,7 +3546,7 @@ static int flexonenand_get_boundary(struct mtd_info *mtd) this->boundary[die] = bdry & FLEXONENAND_PI_MASK; this->command(mtd, ONENAND_CMD_RESET, 0, 0); - ret = this->wait(mtd, FL_RESETING); + this->wait(mtd, FL_RESETING); printk(KERN_INFO "Die %d boundary: %d%s\n", die, this->boundary[die], locked ? "(Locked)" : "(Unlocked)"); @@ -3734,7 +3730,7 @@ static int flexonenand_set_boundary(struct mtd_info *mtd, int die, /* Check is boundary is locked */ this->command(mtd, FLEXONENAND_CMD_READ_PI, die, 0); - ret = this->wait(mtd, FL_READING); + this->wait(mtd, FL_READING); thisboundary = this->read_word(this->base + ONENAND_DATARAM); if ((thisboundary >> FLEXONENAND_PI_UNLOCK_SHIFT) != 3) { @@ -3835,7 +3831,7 @@ static int onenand_chip_probe(struct mtd_info *mtd) static int onenand_probe(struct mtd_info *mtd) { struct onenand_chip *this = mtd->priv; - int maf_id, dev_id, ver_id; + int dev_id, ver_id; int density; int ret; @@ -3843,8 +3839,7 @@ static int onenand_probe(struct mtd_info *mtd) if (ret) return ret; - /* Read manufacturer and device IDs from Register */ - maf_id = this->read_word(this->base + ONENAND_REG_MANUFACTURER_ID); + /* Device and version IDs from Register */ dev_id = this->read_word(this->base + ONENAND_REG_DEVICE_ID); ver_id = this->read_word(this->base + ONENAND_REG_VERSION_ID); this->technology = this->read_word(this->base + ONENAND_REG_TECHNOLOGY); diff --git a/drivers/mtd/ssfdc.c b/drivers/mtd/ssfdc.c index ab2a52a..daf82ba 100644 --- a/drivers/mtd/ssfdc.c +++ b/drivers/mtd/ssfdc.c @@ -290,7 +290,7 @@ static void ssfdcr_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd) int cis_sector; /* Check for small page NAND flash */ - if (mtd->type != MTD_NANDFLASH || mtd->oobsize != OOB_SIZE || + if (!mtd_type_is_nand(mtd) || mtd->oobsize != OOB_SIZE || mtd->size > UINT_MAX) return; diff --git a/drivers/mtd/tests/nandbiterrs.c b/drivers/mtd/tests/nandbiterrs.c index 3cd3aab..6f97615 100644 --- a/drivers/mtd/tests/nandbiterrs.c +++ b/drivers/mtd/tests/nandbiterrs.c @@ -349,7 +349,7 @@ static int __init mtd_nandbiterrs_init(void) goto exit_mtddev; } - if (mtd->type != MTD_NANDFLASH) { + if (!mtd_type_is_nand(mtd)) { pr_info("this test requires NAND flash\n"); err = -ENODEV; goto exit_nand; diff --git a/drivers/mtd/tests/oobtest.c b/drivers/mtd/tests/oobtest.c index ff35c46..2e9e2d1 100644 --- a/drivers/mtd/tests/oobtest.c +++ b/drivers/mtd/tests/oobtest.c @@ -289,7 +289,7 @@ static int __init mtd_oobtest_init(void) return err; } - if (mtd->type != MTD_NANDFLASH) { + if (!mtd_type_is_nand(mtd)) { pr_info("this test requires NAND flash\n"); goto out; } diff --git a/drivers/mtd/tests/pagetest.c b/drivers/mtd/tests/pagetest.c index 44b96e9..ed2d3f6 100644 --- a/drivers/mtd/tests/pagetest.c +++ b/drivers/mtd/tests/pagetest.c @@ -353,7 +353,7 @@ static int __init mtd_pagetest_init(void) return err; } - if (mtd->type != MTD_NANDFLASH) { + if (!mtd_type_is_nand(mtd)) { pr_info("this test requires NAND flash\n"); goto out; } diff --git a/drivers/mtd/tests/subpagetest.c b/drivers/mtd/tests/subpagetest.c index e2c0adf..a876371 100644 --- a/drivers/mtd/tests/subpagetest.c +++ b/drivers/mtd/tests/subpagetest.c @@ -299,7 +299,7 @@ static int __init mtd_subpagetest_init(void) return err; } - if (mtd->type != MTD_NANDFLASH) { + if (!mtd_type_is_nand(mtd)) { pr_info("this test requires NAND flash\n"); goto out; } diff --git a/drivers/mtd/ubi/build.c b/drivers/mtd/ubi/build.c index 315dcc6..e05dc62 100644 --- a/drivers/mtd/ubi/build.c +++ b/drivers/mtd/ubi/build.c @@ -41,6 +41,7 @@ #include <linux/kthread.h> #include <linux/kernel.h> #include <linux/slab.h> +#include <linux/major.h> #include "ubi.h" /* Maximum length of the 'mtd=' parameter */ |