diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 116 |
1 files changed, 84 insertions, 32 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 9de0eed..38f41a5 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -190,7 +190,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on NET_ETHERNET && AVR32 + depends on NET_ETHERNET && (AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263) select MII help The Atmel MACB ethernet interface is found on many AT32 and AT91 @@ -235,16 +235,6 @@ config BMAC To compile this driver as a module, choose M here: the module will be called bmac. -config OAKNET - tristate "National DP83902AV (Oak ethernet) support" - depends on NET_ETHERNET && PPC && BROKEN - select CRC32 - help - Say Y if your machine has this type of Ethernet network card. - - To compile this driver as a module, choose M here: the module - will be called oaknet. - config ARIADNE tristate "Ariadne support" depends on NET_ETHERNET && ZORRO @@ -1155,21 +1145,6 @@ config SEEQ8005 <file:Documentation/networking/net-modules.txt>. The module will be called seeq8005. -config SKMC - tristate "SKnet MCA support" - depends on NET_ETHERNET && MCA && BROKEN - ---help--- - These are Micro Channel Ethernet adapters. You need to say Y to "MCA - support" in order to use this driver. Supported cards are the SKnet - Junior MC2 and the SKnet MC2(+). The driver automatically - distinguishes between the two cards. Note that using multiple boards - of different type hasn't been tested with this driver. Say Y if you - have one of these Ethernet adapters. - - To compile this driver as a module, choose M here and read - <file:Documentation/networking/net-modules.txt>. The module - will be called sk_mca. - config NE2_MCA tristate "NE/2 (ne2000 MCA version) support" depends on NET_ETHERNET && MCA_LEGACY @@ -1788,6 +1763,18 @@ config LAN_SAA9730 workstations. See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>. +config SC92031 + tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" + depends on NET_PCI && PCI && EXPERIMENTAL + select CRC32 + ---help--- + This is a driver for the Fast Ethernet PCI network cards based on + the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you + have one of these, say Y here. + + To compile this driver as a module, choose M here: the module + will be called sc92031. This is recommended. + config NET_POCKET bool "Pocket and portable adapters" depends on NET_ETHERNET && PARPORT @@ -2348,6 +2335,17 @@ config QLA3XXX To compile this driver as a module, choose M here: the module will be called qla3xxx. +config ATL1 + tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)" + depends on NET_PCI && PCI && EXPERIMENTAL + select CRC32 + select MII + help + This driver supports the Attansic L1 gigabit ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl1. + endmenu # @@ -2384,6 +2382,32 @@ config CHELSIO_T1_1G Enables support for Chelsio's gigabit Ethernet PCI cards. If you are using only 10G cards say 'N' here. +config CHELSIO_T1_NAPI + bool "Use Rx Polling (NAPI)" + depends on CHELSIO_T1 + default y + help + NAPI is a driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. + +config CHELSIO_T3 + tristate "Chelsio Communications T3 10Gb Ethernet support" + depends on PCI + help + This driver supports Chelsio T3-based gigabit and 10Gb Ethernet + adapters. + + For general information about Chelsio and our products, visit + our website at <http://www.chelsio.com>. + + For customer support, please visit our customer support page at + <http://www.chelsio.com/support.htm>. + + Please send feedback to <linux-bugs@chelsio.com>. + + To compile this driver as a module, choose M here: the module + will be called cxgb3. + config EHEA tristate "eHEA Ethernet support" depends on IBMEBUS @@ -2480,6 +2504,13 @@ config NETXEN_NIC help This enables the support for NetXen's Gigabit Ethernet card. +config PASEMI_MAC + tristate "PA Semi 1/10Gbit MAC" + depends on PPC64 && PCI + help + This driver supports the on-chip 1/10Gbit Ethernet controller on + PA Semi's PWRficient line of chips. + endmenu source "drivers/net/tokenring/Kconfig" @@ -2514,7 +2545,7 @@ config RIONET_RX_SIZE config FDDI bool "FDDI driver support" - depends on (PCI || EISA) + depends on (PCI || EISA || TC) help Fiber Distributed Data Interface is a high speed local area network design; essentially a replacement for high speed Ethernet. FDDI can @@ -2524,15 +2555,36 @@ config FDDI will say N. config DEFXX - tristate "Digital DEFEA and DEFPA adapter support" - depends on FDDI && (PCI || EISA) - help - This is support for the DIGITAL series of EISA (DEFEA) and PCI - (DEFPA) controllers which can connect you to a local FDDI network. + tristate "Digital DEFTA/DEFEA/DEFPA adapter support" + depends on FDDI && (PCI || EISA || TC) + ---help--- + This is support for the DIGITAL series of TURBOchannel (DEFTA), + EISA (DEFEA) and PCI (DEFPA) controllers which can connect you + to a local FDDI network. + + To compile this driver as a module, choose M here: the module + will be called defxx. If unsure, say N. + +config DEFXX_MMIO + bool + prompt "Use MMIO instead of PIO" if PCI || EISA + depends on DEFXX + default n if PCI || EISA + default y + ---help--- + This instructs the driver to use EISA or PCI memory-mapped I/O + (MMIO) as appropriate instead of programmed I/O ports (PIO). + Enabling this gives an improvement in processing time in parts + of the driver, but it may cause problems with EISA (DEFEA) + adapters. TURBOchannel does not have the concept of I/O ports, + so MMIO is always used for these (DEFTA) adapters. + + If unsure, say N. config SKFP tristate "SysKonnect FDDI PCI support" depends on FDDI && PCI + select BITREVERSE ---help--- Say Y here if you have a SysKonnect FDDI PCI adapter. The following adapters are supported by this driver: |